2001 DODGE RAM steering wheel adjustment

tom of the a/c heater control panel. Refer to Heated
Mirrors for more information on this feature.
The heater-only or a/c heater control panel cannot
be repaired. If faulty or damaged, the entire unit
must be replaced. The control knobs and the illumi-
nation lamps are available for service replacement.
DIAGNOSIS AND TESTING - A/C HEATER
CONTROL
Satisfactory heater and air conditioner perfor-
mance depends upon proper operation and adjust-
ment of all operating controls and refrigeration
system components. For circuit descriptions and dia-
grams, (Refer to Appropriate Wiring Information).
These inspections, tests, and adjustments should be
used to locate the cause of a malfunction.
Operation must be tested as described in the fol-
lowing sequence:
(1) Inspect and adjust the serpentine drive belt.
Refer to Cooling for the procedures.
(2) Start the engine and hold the idle speed at
1,300 rpm.
(3) On vehicles with air conditioning, turn the
temperature control knob to the extreme counter-
clockwise (Cool) position, and set the mode control
switch knob to the Bi-Level (A/C) position. The out-
side (recirculation) air door should be open to outside
air. If not OK, (Refer to 24 - HEATING & AIR CON-
DITIONING/CONTROLS - DIAGNOSIS AND TEST-
ING - VACUUM SYSTEM).
(4) Open the vehicle windows. Test the blower
motor operation in all speeds. If not OK, (Refer to 24
- HEATING & AIR CONDITIONING/DISTRIBU-
TION/BLOWER MOTOR - DIAGNOSIS AND TEST-
ING).
(5) On vehicles with air conditioning, the compres-
sor should be running and the air conditioning sys-
tem in operation unless the ambient air temperature
is below about -1É C (30É F). If not OK, (Refer to 24 -
HEATING & AIR CONDITIONING - DIAGNOSIS
AND TESTING - A/C PERFORMANCE).
(6) Check the mode control switch operation. The
heater and air conditioner systems should respond as
described in the owner's manual in the vehicle glove
box to each mode selected. Reduce the engine speed
to normal idle. The vacuum will be high at low idle
and the vacuum actuators should respond quickly. If
not OK, (Refer to 24 - HEATING & AIR CONDI-
TIONING/CONTROLS - DIAGNOSIS AND TEST-
ING - VACUUM SYSTEM).
(7) If the vacuum tests, and the electrical compo-
nent and circuit tests reveal no problems, disassem-
ble the HVAC housing to inspect for mechanical
misalignment or binding of the mode doors. (Refer to
24 - HEATING & AIR CONDITIONING/DISTRIBU-
TION/HVAC HOUSING - DISASSEMBLY)
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
(1) Disconnect and isolate the battery negative
cable.
(2) Reach under the instrument panel near the
driver side of the floor panel transmission tunnel and
unplug the a/c heater control to HVAC housing vac-
uum harness connector.
(3) While still reaching under the instrument
panel, disengage the retainer on the a/c heater con-
trol half of the vacuum harness from the hole in the
center distribution duct (Fig. 18).
(4) Remove the cluster bezel from the instrument
panel. Refer to Instrument Panel System for the pro-
cedures.
Fig. 18 A/C HEATER CONTROL VACUUM HARNESS
ROUTING
1 - A/C HEATER CONTROL VACUUM HARNESS
2 - REINFORCEMENT
3 - RETAINER
4 - CENTER DISTRIBUTION DUCT
BR/BECONTROLS 24 - 19
A/C HEATER CONTROL (Continued)

Items found requiring adjustment and/or repair
should be corrected before delivery of the vehicle.
NOTE: It is the dealer's responsibility to protect
new vehicles from damage and deterioration prior
to retail delivery both before and after new vehicle
preparation.
The information includes the following features:
Inspection points are cross-referenced to the New
Vehicle Preparation Form as follows:
²Titles indicate the general area being inspected
or the types of checks being made (i.e., underhood,
body-exterior, road test, etc.).
²Sub-Titles identify the types of items to be
inspected in that area (i.e., lines/hoses, wiring, etc.).
Procedures follow a logical order to prevent dupli-
cation and wasted effort.
Tips to help you do a better job are found as
NOTES.
RECEIVING
INSPECTION
The following procedures are recommended for
your own protection upon receipt of new vehicles.
When a new car is delivered by the carrier, it should
be inspected to ensure that it is in good condition
and to determine if there is any shortage or transpor-
tation damage.
EXTERIOR
Upon receipt of a new vehicle, check immediately
for:
²Under carriage damage
²Chipped or cracked windshield, broken windows,
and loose or missing moldings and name-plates
²Dents, scrapes, scratches, chips, dirt in paints or
other damage to the body exterior
²Damaged or missing side view mirror(s)
²Missing wheel nuts
²Broken or missing lenses
²Chafing, bruises, cuts, or scrapes on tire side-
walls or tread
²Missing underhood items
²Missing fuel filler cap
²Shipped loose items-license plate bracket, spare
tire, jack and tire wrench, radio antenna, floor mats,
wheel covers, cargo nets, fuses and other items²Ensure that IOD fuse is removed
²Check battery test indicator when easily visible,
or use voltmeter (battery must be at 12.4 volts or
greater). Charge to ensure green dot-visibility, per-
manent damage may occur if battery remains in a
discharged state for any length of time.
INTERIOR
Check interior items such as:
²Rearview mirror
²Accessory control knobs
²Smokers package items
²Keys
²Radio
²Special equipment items listed on shipper
²Owner's Manual and Consumer information Bro-
chures (normally stored in the glove box).
²Cuts, abrasions or stains on interior trim.
NOTE: Remember a careful look at new vehicles
when they are received may prevent problems when
preparing vehicles for delivery to your customers.
MAJOR INSPECTION POINTS
(1) Check operation of hood latch and safety catch-
adjust as required.
(2) Check all fluids for proper level and top off
with the proper fluid as required-engine oil, auto-
matic transmission fluid, brake master cylinder,
clutch master cylinder, power steering, windshield
washer, and cooling system. (Vehicle must be at nor-
mal operating temperature for some of these checks.)
(3) Check brake, clutch, fuel, and power steering
lines and hoses for leaks and clearance from moving
and hot objects-reroute to the proper location and
tighten as required.
(4) Check battery state of charge-recharge if neces-
sary, to ensure green dot is visible or instrument
panel voltmeter indicates 12.4 volts or greater.
(5) Check routing and connections of underhood
wiring, vacuum hoses, refrigerant lines and coolant
hoses for leaks, loose connections and clearance from
moving objects reroute and tighten connections as
required. Install IOD fuse on applicable vehicles.
NOTE: Reset radio, clock, compass, etc., after
installing, if vehicle is being delivered.
BR/BENEW VEHICLE PREPARATION 30 - 3
INTRODUCTION (Continued)

ROAD TEST
DESCRIPTION - ROAD TEST INSPECTION
The following items must be inspected during the
road test portion of the new vehicle inspection.
²Check neutral safety switch operation
²Check operation of shift/clutch interlock system
²Check operation of gauges and warning lights
²Check horn operation
²Check operation of turn signals and emergency
flashers
²Check all mirror adjustments, including day/
night function
²Check windshield wipers for proper wipe pattern
and intermittent mode (if equipped)
²Check washer spray pattern
²Check heater, defroster and air conditioning for
proper operation
²Check that the fan operates quietly
²Check the rear window defroster (if equipped)
²Leave air selection lever in the fresh air position
²Check the rear heater and air conditioning for
proper operation
²Check the rear air register locations
²Check that the indicator lamps operate properly
²Check the operation of the radio, cassette and/or
compact disc player, and that sound quality is good
²Ensure that the clock displays the correct time
²Check that the trip computer/maintenance
reminder operates in all modes
²Check all speed control functions
²Check the service brakes to ensure that they
stop the vehicle in a straight line, without noise,
shudder or vibration
²Check the brake warning light
²Check the parking brake operation
²Check the engine's performance
²Check the transmission's performance for
smooth, quiet operation. If the vehicle is a 4x4, check
that the transfer case shifts easily among all ranges
²Check Autostick function (if equipped)
²Check the vehicle's steering and handling
²The steering wheel should be centered when
traveling in a straight line
²The vehicle should not pull or vibrate
²Check for squeaks, rattles and wind noise
²Check any other vehicle aspects you believe are
important, but that may not be included on the New
Vehicle Preparation Form
²Fill fuel tank with specified grade of fuel
INSPECTION - FUEL
Fill fuel tank with specified grade of gasoline (reg-
ular, midgrade or premium).
INSPECTION - OTHER
As part of DaimlerChrysler's Customer One philos-
ophy, the ªOtherº blank is provided on the New Vehi-
cle Preparation Form. This is designed to encourage
you to check any aspects of vehicle operation that
you believe are important to your customers, but that
do not appear elsewhere on the form.
INSPECTION - SQUEAKS, RATTLES AND WIND
NOISE
(1) Make sure that the instrument panel, glove
box, seats, steering wheel and column are free from
squeaks and rattles. Tighten any obvious loose fas-
teners.
(2) Check that the windows and doors are free
from squeaks, rattles and wind noise.
(3) Check that the vehicle exterior is free from
squeaks, rattles and noise, front and rear.
(4) Make sure that all interior panels are free from
squeaks and rattles.
INSPECTION - STEERING AND HANDLING
(1) Check that the power assist works properly (if
equipped). Steering should not require excessive
effort.
(2) Make sure the steering wheel does not vibrate
at idle or road speed.
(3) Ensure that the steering wheel is centered
when traveling straight ahead.
(4) Check that the vehicle does not drift to one
side.
(5) Make sure that the vehicle does not vibrate/
shake.
INSPECTION - TRANSMISSION/TRANSFER
CASE
AUTOMATIC TRANSMISSION
(1) Make sure that the park lock holds the vehicle
With the vehicle on a grade, put automatic trans-
mission in PARK and slowly release the service
brake to see if park lock holds. If it does not hold, the
transmission requires further service.
(2) Make sure shift lever operates easily/ smoothly
(Fig. 36).
Check for smooth shifting. Check for proper
upshifting and downshifting.
MANUAL TRANSMISSION
(1) Check that the shifter operates easily (Fig. 38).
(2) Make sure that the clutch operates smoothly
(Fig. 37).
(3) Look for proper synchronization.
The gears should not grind.
BR/BENEW VEHICLE PREPARATION 30 - 15

FAN - 3.9L/5.2L/5.9L/8.0L -
INSTALLATION, RADIATOR..............7-43
FAN - 3.9L/5.2L/5.9L/8.0L - REMOVAL,
RADIATOR...........................7-42
FAN - 5.9L DIESEL - CLEANING,
RADIATOR...........................7-44
FAN - 5.9L DIESEL - INSPECTION,
RADIATOR...........................7-44
FAN - 5.9L DIESEL - INSTALLATION,
RADIATOR...........................7-45
FAN - 5.9L DIESEL - REMOVAL,
RADIATOR...........................7-44
FAN DRIVE - DIAGNOSIS AND TESTING,
VISCOUS........................7-56,7-58
FAN DRIVE VISCOUS CLUTCH -
3.9L/5.2L/5.9L/8.0L - DESCRIPTION.......7-56
FAN DRIVE VISCOUS CLUTCH -
3.9L/5.2L/5.9L/8.0L - OPERATION.........7-56
FAN DRIVE VISCOUS CLUTCH - 5.9L
DIESEL - DESCRIPTION................7-57
FAN DRIVE VISCOUS CLUTCH - 5.9L
DIESEL - OPERATION..................7-57
FASCIA - ADJUSTMENT, FRONT..........13-2
FASCIA - INSTALLATION, FRONT.........13-2
FASCIA - INSTALLATION, FRONT LOWER . . . 13-3
FASCIA - REMOVAL, FRONT.............13-2
FASCIA - REMOVAL, FRONT LOWER......13-3
FASCIA-SPORT - INSTALLATION, FRONT . . . 13-3
FASCIA-SPORT - REMOVAL, FRONT.......13-3
FASTENER IDENTIFICATION -
DESCRIPTION......................Intro.-3
FASTENER USAGE - DESCRIPTION......Intro.-6
FASTENERS - DESCRIPTION, PUSH-IN.....23-1
FEATURES - DESCRIPTION,
PROGRAMMABLE ELECTRONIC.........30-20
FEATURES - OPERATION,
PROGRAMMABLE ELECTRONIC.........30-20
FENDER - INSTALLATION, LEFT FRONT . . . 23-93
FENDER - INSTALLATION, REAR.........23-95
FENDER - INSTALLATION, RIGHT FRONT . . 23-94
FENDER - REMOVAL, LEFT FRONT.......23-92
FENDER - REMOVAL, REAR............23-95
FENDER - REMOVAL, RIGHT FRONT......23-94
FILL - STANDARD PROCEDURE,
TRANSMISSION . . . 21-201,21-372,21-547,21-718
FILL DOOR - INSTALLATION, FUEL.......23-95
FILL DOOR - REMOVAL, FUEL..........23-95
FILLER CAP - DESCRIPTION, FUEL.......25-33
FILLER CAP - OPERATION, FUEL........25-33
FILLER CAP - REMOVAL/INSTALLATION,
FUEL..............................25-33
FILTER - DESCRIPTION, PCV...........25-35
FILTER - INSTALLATION, AIR PUMP......25-29
FILTER - INSTALLATION, INLET..........14-22
FILTER - INSTALLATION, OIL . 9-105,9-161,9-218,
9-296,9-48
FILTER - REMOVAL, AIR PUMP.........25-29
FILTER - REMOVAL, INLET.............14-22
FILTER - REMOVAL, OIL.....9-105,9-161,9-218,
9-296,9-48
FILTER - STANDARD PROCEDURES,
WATER DRAINING AT FUEL............14-56
FILTER / WATER SEPARATOR -
DESCRIPTION, FUEL..................14-59
FILTER / WATER SEPARATOR -
INSTALLATION, FUEL.................14-61
FILTER / WATER SEPARATOR -
OPERATION, FUEL....................14-59
FILTER / WATER SEPARATOR -
REMOVAL, FUEL.....................14-60
FILTER REPLACEMENT - STANDARD
PROCEDURE, FLUID.....21-201,21-372,21-547,
21-717
FILTER/PRESSURE REGULATOR -
DESCRIPTION, FUEL...................14-5
FILTER/PRESSURE REGULATOR -
INSTALLATION, FUEL..................14-6
FILTER/PRESSURE REGULATOR -
OPERATION, FUEL.....................14-5
FILTER/PRESSURE REGULATOR -
REMOVAL, FUEL
......................14-5
FINAL STEPS - NEW VEHICLE
PREPARATION FORM
.................30-22
FINISH - DESCRIPTION, BASE
COAT/CLEAR COAT
..................23-129
FINISH - INSPECTION, FIT
........30-10,30-12
FINISH - OPERATION, BASE COAT/CLEAR
COAT
.............................23-129FIRING ORDER, 3.9L V-6 ENGINE -
ENGINE..............................8I-2
FIRING ORDER, 5.2L/5.9L V-8 ENGINES -
ENGINE..............................8I-2
FIRING ORDER, DIESEL - FUEL
INJECTOR..........................14-58
FIT AND FINISH - INSPECTION.....30-10,30-12
FITTING - DESCRIPTION, QUICK
CONNECT...........................14-22
FITTING - STANDARD PROCEDURE,
CONNECTING ROD BEARING . . 9-144,9-202,9-88
FITTING - STANDARD PROCEDURE,
CRANKSHAFT MAIN BEARING......9-146,9-90
FITTING - STANDARD PROCEDURE,
MAIN BEARING..................9-203,9-33
FITTING - STANDARD PROCEDURE,
PISTON...............9-153,9-208,9-40,9-97
FITTING - STANDARD PROCEDURE,
PISTON RING...............9-154,9-41,9-98
FITTING, CONNECTING ROD BEARINGS -
STANDARD PROCEDURE-CONNECTING
ROD BEARING........................9-31
FITTING PISTON RINGS - STANDARD
PROCEDURE........................9-211
FITTING, PISTON RINGS - STANDARD
PROCEDURE-PISTON RING.............9-288
FITTINGS - STANDARD PROCEDURES,
QUICK-CONNECT.....................14-22
FIXED ORIFICE TUBE - DIAGNOSIS AND
TESTING...........................24-54
FLAG - INSTALLATION, SIDE VIEW
MIRROR...........................23-74
FLAG - REMOVAL, SIDE VIEW MIRROR . . . 23-74
FLARING - STANDARD PROCEDURE,
DOUBLE INVERTED.....................5-8
FLARING - STANDARD PROCEDURE, ISO....5-8
FLASHER - DESCRIPTION, COMBINATION . . 8L-7
FLASHER - INSTALLATION,
COMBINATION........................8L-8
FLASHER - OPERATION, COMBINATION....8L-7
FLASHER - REMOVAL, COMBINATION.....8L-8
FLOOR MATS - INSTALLATION, CARPETS . 23-123
FLOOR MATS - REMOVAL, CARPETS....23-123
FLOOR SHIFT BOOT - INSTALLATION,
4WD .............................23-122
FLOOR SHIFT BOOT - REMOVAL, 4WD . . . 23-122
FLOOR STOWAGE TRAY -
INSTALLATION, REAR................23-121
FLOOR STOWAGE TRAY - REMOVAL,
REAR.............................23-121
FLOW - 3.9L/5.2L/5.9L ENGINE -
DESCRIPTION, COOLING SYSTEM.........7-1
FLOW - 5.9L DIESEL - DESCRIPTION,
COOLING SYSTEM.....................7-1
FLOW - DIAGNOSIS AND TESTING,
RADIATOR COOLANT..........7-59,7-61,7-63
FLOW AND PRESSURE - DIAGNOSIS
AND TESTING, POWER STEERING........19-4
FLUID - DESCRIPTION, AUTOMATIC
TRANSMISSION.......................0-5
FLUID - DESCRIPTION, TRANSFER CASE....0-5
FLUID - DIAGNOSIS AND TESTING,
CAUSES OF BURNT.....21-199,21-370,21-545,
21-715
FLUID - OPERATION, AUTOMATIC
TRANSMISSION.......................0-5
FLUID AND FILTER REPLACEMENT -
STANDARD PROCEDURE . 21-201,21-372,21-547,
21-717
FLUID CAPACITIES, SPECIFICATIONS.......0-6
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING....21-199,21-370,21-545,21-715
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING, BRAKE..................5-14
FLUID DRAIN AND REFILL - STANDARD
PROCEDURE...........21-851,21-885,21-922
FLUID INDICATOR - DESCRIPTION,
WASHER
...........................8J-35
FLUID INDICATOR - DIAGNOSIS AND
TESTING, WASHER
...................8J-36
FLUID INDICATOR - OPERATION,
WASHER
...........................8J-35
FLUID LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING
. . . 21-148,21-319,21-491,
21-662
FLUID LEVEL - DIAGNOSIS AND
TESTING, EFFECTS OF INCORRECT
.....21-199,
21-370,21-545,21-715FLUID LEVEL - STANDARD PROCEDURE,
BRAKE..............................5-14
FLUID LEVEL CHECK - STANDARD
PROCEDURE.....21-199,21-370,21-545,21-715
FLUID LEVEL SWITCH - DESCRIPTION,
WASHER............................8R-7
FLUID LEVEL SWITCH - INSTALLATION,
WASHER............................8R-8
FLUID LEVEL SWITCH - OPERATION,
WASHER............................8R-7
FLUID LEVEL SWITCH - REMOVAL,
WASHER............................8R-8
FLUID LEVELS - INSPECTION............30-4
FLUID RESERVOIR - INSTALLATION.......5-15
FLUID RESERVOIR - REMOVAL..........5-15
FLUID, SPECIFICATIONS - BRAKE.........5-15
FLUID TYPES - DESCRIPTION.............0-5
FLUSH MEASUREMENTS,
SPECIFICATIONS - BODY GAP..........23-56
FLUSHING - STANDARD PROCEDURE,
COOLING SYSTEM CLEANING/
REVERSE............................7-16
FLUSHING COOLER AND TUBES -
WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE.......7-80,7-83,7-86
FLUSHING COOLERS AND TUBES - WITH
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE.................7-79,7-83,7-85
FLUSHING POWER STEERING SYSTEM -
STANDARD PROCEDURE...............19-32
FLYWHEEL - ASSEMBLY................6-17
FLYWHEEL - DESCRIPTION..............6-16
FLYWHEEL - DIAGNOSIS AND TESTING....6-17
FLYWHEEL - DISASSEMBLY.............6-17
FLYWHEEL - OPERATION...............6-16
FOG LAMP - DIAGNOSIS AND TESTING....8L-9
FOG LAMP - INSTALLATION............8L-11
FOG LAMP - REMOVAL................8L-11
FOG LAMP UNIT - ADJUSTMENTS.......8L-12
FOG LAMP UNIT - INSTALLATION........8L-12
FOG LAMP UNIT - REMOVAL...........8L-11
FORE/AFT - ADJUSTMENT, FRONT DOOR . . 23-68
FORM, FINAL STEPS - NEW VEHICLE
PREPARATION.......................30-22
FORM-IN-PLACE GASKETS & SEALERS -
STANDARD PROCEDURE.....9-11,9-125,9-180,
9-237,9-68
FOUR-WHEEL DRIVE INDICATOR -
DIAGNOSIS AND TESTING..............8J-29
FRAME - DESCRIPTION.................13-6
FRAME - FRAME SERVICE..............13-6
FRAME - INSTALLATION, GRILLE........23-92
FRAME - REMOVAL, GRILLE............23-91
FRAME DIMENSION, SPECIFICATIONS.....13-7
FRAME SERVICE, FRAME...............13-6
FRONT - 2WD - DESCRIPTION.........2-7,2-8
FRONT - 4WD - DESCRIPTION...........2-14
FRONT - DESCRIPTION, CRANKSHAFT
OIL SEAL...................9-147,9-34,9-91
FRONT - INSTALLATION............5-14,5-27
FRONT - INSTALLATION...............22-12
FRONT - INSTALLATION, 1500/2500.......5-22
FRONT - INSTALLATION, 3500...........5-22
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL..............9-148,9-277,9-34,9-91
FRONT - INSTALLATION, PROPELLER
SHAFT...............................3-8
FRONT - OPERATION, CRANKSHAFT OIL
SEAL......................9-147,9-34,9-91
FRONT - REMOVAL................5-10,5-24
FRONT - REMOVAL, 1500/2500..........5-21
FRONT - REMOVAL, 3500...............5-22
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL.................9-147,9-276,9-34,9-91
FRONT - REMOVAL, PROPELLER SHAFT....3-8
FRONT AIR DAM - INSTALLATION........13-2
FRONT AIR DAM - REMOVAL............13-1
FRONT AXLE - 216FBI - ADJUSTMENTS....3-17
FRONT AXLE - 216FBI - DESCRIPTION.....3-12
FRONT AXLE - 216FBI - INSTALLATION....3-17
FRONT AXLE - 216FBI - OPERATION......3-12
FRONT AXLE - 216FBI - REMOVAL
........3-16
FRONT AXLE - 248FBI - ADJUSTMENTS
....3-50
FRONT AXLE - 248FBI - DESCRIPTION
.....3-45
FRONT AXLE - 248FBI - INSTALLATION
....3-50
FRONT AXLE - 248FBI - OPERATION
......3-45
14 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

INJECTION PUMP TIMING - DIAGNOSIS
AND TESTING, FUEL..................14-66
INJECTION SYSTEM - DESCRIPTION, AIR . 25-25
INJECTION SYSTEM - DESCRIPTION,
DIESEL FUEL........................14-87
INJECTION SYSTEM - OPERATION, AIR . . . 25-27
INJECTION SYSTEM - TORQUE, AIR......25-28
INJECTOR - DESCRIPTION, FUEL . . . 14-53,14-93
INJECTOR - INSTALLATION, FUEL . . 14-53,14-98
INJECTOR - OPERATION, FUEL.....14-53,14-94
INJECTOR - REMOVAL, FUEL......14-53,14-96
INJECTOR FIRING ORDER, DIESEL -
FUEL..............................14-58
INJECTOR TEST - DIAGNOSIS AND
TESTING, FUEL.................14-53,14-95
INLET BAFFLE - INSTALLATION, HVAC
HOUSING...........................24-37
INLET BAFFLE - REMOVAL, HVAC
HOUSING...........................24-36
INLET FILTER - INSTALLATION..........14-22
INLET FILTER - REMOVAL..............14-22
INNER BELT WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-154
INNER BELT WEATHERSTRIP -
REMOVAL, FRONT DOOR.............23-154
IN/OUT - ADJUSTMENT, FRONT DOOR....23-69
INPUT - DESCRIPTION, VEHICLE SPEED . . . 8P-1
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-3
INSIDE HANDLE ACTUATOR -
INSTALLATION...................23-71,23-80
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-71,
23-80
INSPECTION - DESCRIPTION, ROAD
TEST..............................30-15
INSPECTION - DIAGNOSIS AND
TESTING, WHEEL....................22-10
INSPECTION - INFORMATION LABELS -
STANDARD PROCEDURE...............30-22
INSPECTION, 3.9L/5.2L/5.9L ENGINES -
VISUAL............................14-28
INSPECTION, 8.0L ENGINE - VISUAL.....14-32
INSPECTION, A/C COMPRESSOR
CLUTCH............................24-16
INSPECTION, ACCUMULATOR . . . 21-192,21-363,
21-538,21-708
INSPECTION, AUTOMATIC
TRANSMISSION - 42RE...............21-165
INSPECTION, AUTOMATIC
TRANSMISSION - 44RE...............21-337
INSPECTION, AUTOMATIC
TRANSMISSION - 46RE...............21-510
INSPECTION, AUTOMATIC
TRANSMISSION - 47RE...............21-681
INSPECTION, BATTERY.................30-7
INSPECTION, BATTERY SYSTEM..........8F-5
INSPECTION, BODY SEALING...........30-10
INSPECTION, CAMSHAFT & BEARINGS
(IN BLOCK).........................9-272
INSPECTION, CATALYTIC CONVERTER -
3.9L/5.2L/5.9L........................11-5
INSPECTION, CATALYTIC CONVERTER -
5.9L HEAVY DUTY/8.0L.................11-7
INSPECTION, CHARGE AIR COOLER AND
PLUMBING.........................11-18
INSPECTION, COMPASS...............30-12
INSPECTION, CROSSHEADS............9-250
INSPECTION, CYLINDER HEAD....9-137,9-193,
9-23,9-250,9-80
INSPECTION, CYLINDER HEAD COVER(S) . 9-138,
9-194,9-24,9-253,9-81
INSPECTION, DISC BRAKE CALIPERS......5-12
INSPECTION, DOORS AND DOOR LOCKS . . 30-11
INSPECTION, DRUM...................5-33
INSPECTION, ENGINE BLOCK . 9-142,9-200,9-267,
9-28,9-86
INSPECTION, ENGINE PERFORMANCE....30-16
INSPECTION, EXHAUST MANIFOLD . 9-112,9-168,
9-225,9-304,9-55
INSPECTION, EXHAUST PIPE -
3.9L/5.2L/5.9L........................11-7
INSPECTION, EXHAUST PIPE - 5.9L
DIESEL
.............................11-9
INSPECTION, EXHAUST PIPE - 5.9L
HEAVY DUTY/8.0L
.....................11-9
INSPECTION, FIT AND FINISH
......30-10,30-12
INSPECTION, FLUID LEVELS
.............30-4
INSPECTION, FRONT CLUTCH
. . . 21-205,21-376,
21-550,21-721INSPECTION, FRONT SERVO....21-207,21-378,
21-553,21-723
INSPECTION, FUEL...................30-15
INSPECTION, GAUGES/WARNING LIGHTS . 30-19
INSPECTION, HEATER/AIR CONDITIONER . . 30-17
INSPECTION, HOOD LATCH/SAFETY
CATCH ..............................30-4
INSPECTION, HORN..................30-19
INSPECTION, INTAKE MANIFOLD . . . 9-110,9-166,
9-223,9-302,9-53
INSPECTION, INTAKE/EXHAUST VALVES
& SEATS ..............9-141,9-198,9-27,9-84
INSPECTION, KEYLESS ENTRY..........30-11
INSPECTION, LIGHTS AND SWITCHES....30-12
INSPECTION, LINES/HOSES.............30-6
INSPECTION, MANUAL - NV3500........21-15
INSPECTION, MEASURING TIMING
CHAIN STRETCH.......9-114,9-170,9-227,9-58
INSPECTION, MIRROR................30-19
INSPECTION, NEUTRAL SAFETY SWITCH . . 30-19
INSPECTION, OIL COOLER & LINES -
CLEANING..........................9-296
INSPECTION, OIL PAN . 9-106,9-162,9-219,9-297,
9-49
INSPECTION, OIL PRESSURE RELIEF
VALVE .............................9-297
INSPECTION, OIL PUMP....9-107,9-163,9-220,
9-299,9-50
INSPECTION, OIL PUMP . . 21-211,21-382,21-557,
21-728
INSPECTION, OTHER..................30-15
INSPECTION, OVERDRIVE UNIT . . 21-224,21-394,
21-569,21-741
INSPECTION, OVERRUNNING CLUTCH
CAM/OVERDRIVE PISTON RETAINER....21-236,
21-406,21-580,21-752
INSPECTION, PARKING BRAKE..........30-17
INSPECTION, PISTON & CONNECTING
ROD ............9-154,9-209,9-285,9-41,9-98
INSPECTION, PLANETARY GEARTRAIN/
OUTPUT SHAFT . . . 21-241,21-411,21-587,21-760
INSPECTION, PUSHRODS..............9-250
INSPECTION, RADIATOR - 3.9L/5.2L/5.9L . . . 7-61
INSPECTION, RADIATOR - 5.9L DIESEL....7-65
INSPECTION, RADIATOR - 8.0L..........7-62
INSPECTION, RADIATOR FAN -
3.9L/5.2L/5.9L/8.0L....................7-43
INSPECTION, RADIATOR FAN - 5.9L
DIESEL.............................7-44
INSPECTION, RADIATOR PRESSURE CAP . . . 7-66
INSPECTION, RADIO..................30-17
INSPECTION, REAR CLUTCH....21-248,21-419,
21-593,21-765
INSPECTION, RECEIVING...............30-3
INSPECTION, ROCKER ARM / ADJUSTER
ASSY..............................9-262
INSPECTION, SEAT BELTS, SHOULDER
BELTS, RETRACTORS AND HEAD
RESTRAINTS........................30-12
INSPECTION, SEATS..................30-13
INSPECTION, SERVICE BRAKES.........30-17
INSPECTION, SHIFT/CLUTCH INTERLOCK
SYSTEM............................30-19
INSPECTION, SOLID LIFTERS/TAPPETS . . . 9-281
INSPECTION, SPEED CONTROL.........30-17
INSPECTION, SQUEAKS, RATTLES AND
WIND NOISE........................30-15
INSPECTION, STEERING AND HANDLING
. . 30-15
INSPECTION, TAILPIPE - 3.9L/5.2L/5.9L
. . . 11-11
INSPECTION, TAILPIPE - 5.9L DIESEL
....11-12
INSPECTION, TAILPIPE - 5.9L HEAVY
DUTY/8.0L
..........................11-12
INSPECTION, TIRE PRESSURES
..........30-8
INSPECTION, TRANSFER CASE -
NV231HD
..........................21-832
INSPECTION, TRANSFER CASE -
NV241HD
..........................21-902
INSPECTION, TRANSFER CASE -
NV241LD
..........................21-867
INSPECTION, TRANSMISSION
.....21-109,21-64
INSPECTION, TRANSMISSION/TRANSFER
CASE
..............................30-15
INSPECTION, TRIP COMPUTER/
MAINTENANCE REMINDER
.............30-17
INSPECTION, TURBOCHARGER
..........11-16
INSPECTION, TURN AND EMERGENCY
SIGNALS
...........................30-19INSPECTION, VALVE BODY......21-293,21-465,
21-637,21-809
INSPECTION, VIBRATION DAMPER.......9-289
INSPECTION, VISUAL..................30-8
INSPECTION, WATER PUMP -
3.9L/5.2L/5.9L........................7-69
INSPECTION, WATER PUMP - 5.9L
DIESEL.............................7-73
INSPECTION, WATER PUMP - 8.0L........7-72
INSPECTION, WHEEL CYLINDERS........5-31
INSPECTION, WINDOWS, DOORS AND
LOCKS.............................30-14
INSPECTION WINDSHIELD WIPERS/
WASHERS, ROAD TEST................30-18
INSPECTION, WIPER & WASHER
SYSTEM............................8R-6
INSPECTION, WIRING..................30-7
INSTALLED - INSTALLATION, FRONT OIL
SEAL - FRONT COVER.................9-205
INSTALLED - REMOVAL, FRONT OIL
SEAL - FRONT COVER.................9-204
INSTRUMENT CLUSTER - ASSEMBLY.....8J-13
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING........................8J-6
INSTRUMENT CLUSTER - DISASSEMBLY . . 8J-11
INSTRUMENT CLUSTER - INSTALLATION . . 8J-14
INSTRUMENT CLUSTER - OPERATION.....8J-3
INSTRUMENT CLUSTER - REMOVAL.....8J-10
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-10
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-9
INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL.........................24-37
INSTRUMENT PANEL DUCTS - REMOVAL . 24-37
INSTRUMENT PANEL SYSTEM -
DESCRIPTION......................23-104
INSTRUMENT PANEL SYSTEM -
INSTALLATION......................23-107
INSTRUMENT PANEL SYSTEM -
OPERATION........................23-105
INSTRUMENT PANEL SYSTEM -
REMOVAL.........................23-106
INSTRUMENT PANEL TOP COVER -
INSTALLATION......................23-115
INSTRUMENT PANEL TOP COVER -
REMOVAL.........................23-114
INTAKE AIR HEATER - DESCRIPTION....14-100
INTAKE AIR HEATER - INSTALLATION....14-101
INTAKE AIR HEATER - OPERATION......14-100
INTAKE AIR HEATER - REMOVAL.......14-100
INTAKE AIR HEATER RELAY -
DESCRIPTION......................14-101
INTAKE AIR HEATER RELAY -
INSTALLATION......................14-102
INTAKE AIR HEATER RELAY -
OPERATION........................14-102
INTAKE AIR HEATER RELAY - REMOVAL . 14-102
INTAKE MANIFOLD - CLEANING
....9-110,9-166,
9-223,9-302,9-53
INTAKE MANIFOLD - DESCRIPTION
. 9-109,9-165,
9-222,9-52
INTAKE MANIFOLD - INSPECTION
. . 9-110,9-166,
9-223,9-302,9-53
INTAKE MANIFOLD - INSTALLATION
.....9-111,
9-166,9-223,9-302,9-53
INTAKE MANIFOLD - OPERATION
. . 9-109,9-165,
9-52
INTAKE MANIFOLD - REMOVAL
....9-110,9-166,
9-222,9-301,9-53
INTAKE MANIFOLD LEAKAGE -
DIAGNOSIS AND TESTING
. . . 9-110,9-165,9-222,
9-53
INTAKE/EXHAUST VALVES & SEATS -
CLEANING
.............9-140,9-198,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION
.....9-138,9-195,9-25,9-253,9-81
INTAKE/EXHAUST VALVES & SEATS -
INSPECTION
...........9-141,9-198,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION
.........9-141,9-260,9-28,9-85
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL
.............9-140,9-258,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
STANDARD PROCEDURE-
VALVES,GUIDES AND SPRINGS
.........9-253
BR/BEINDEX 19
Description Group-Page Description Group-Page Description Group-Page

LEVEL SWITCH - DESCRIPTION,
WASHER FLUID......................8R-7
LEVEL SWITCH - INSTALLATION,
WASHER FLUID......................8R-8
LEVEL SWITCH - OPERATION, WASHER
FLUID..............................8R-7
LEVEL SWITCH - REMOVAL, WASHER
FLUID..............................8R-8
LEVELS - INSPECTION, FLUID...........30-4
LEVER - ADJUSTMENT, SHIFT . . . 21-853,21-888,
21-925
LEVER - INSTALLATION, GEAR SHIFT.....19-13
LEVER - INSTALLATION, SHIFT . . 21-853,21-888,
21-924
LEVER - REMOVAL, GEAR SHIFT........19-13
LEVER - REMOVAL, SHIFT......21-852,21-887,
21-924
LICENSE PLATE LAMP - INSTALLATION . . . 8L-22
LICENSE PLATE LAMP - REMOVAL.......8L-22
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-22
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-22
LID - INSTALLATION, CENTER CONSOLE . 23-132
LID - REMOVAL, CENTER CONSOLE.....23-131
LIFTERS - CLEANING, HYDRAULIC . . 9-152,9-208
LIFTERS - INSTALLATION, HYDRAULIC . . . 9-152,
9-208
LIFTERS - REMOVAL, HYDRAULIC . . 9-152,9-207
LIFTERS (CAM IN BLOCK) - CLEANING,
HYDRAULIC......................9-39,9-96
LIFTERS (CAM IN BLOCK) -
INSTALLATION, HYDRAULIC.........9-39,9-96
LIFTERS (CAM IN BLOCK) - REMOVAL,
HYDRAULIC......................9-39,9-96
LIFTERS/TAPPETS - CLEANING, SOLID....9-281
LIFTERS/TAPPETS - INSPECTION, SOLID . . 9-281
LIFTERS/TAPPETS - INSTALLATION,
SOLID.............................9-281
LIFTERS/TAPPETS - REMOVAL, SOLID....9-280
LIGHT DUTY ENGINE (1500 AND 2500
MODELS EXCEPT 8.0L) MAINTENANCE
SCHEDULES, MAINTENANCE
SCHEDULES..........................0-7
LIGHTER - DIAGNOSIS & TESTING,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - INSTALLATION,
CIGAR...........................8W-97-3
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIGHTER OUTLET - REMOVAL, CIGAR . . 8W-97-3
LIGHTS - INSPECTION, GAUGES/
WARNING..........................30-19
LIGHTS AND SWITCHES - INSPECTION . . . 30-12
LINE - INSTALLATION, LIQUID..........24-52
LINE - INSTALLATION, SUCTION AND
DISCHARGE.........................24-51
LINE - REMOVAL, LIQUID..............24-52
LINE - REMOVAL, SUCTION AND
DISCHARGE.........................24-50
LINE COUPLERS - DESCRIPTION, A/C....24-40
LINE COUPLERS - OPERATION, A/C......24-41
LINE COUPLERS - STANDARD
PROCEDURE, A/C....................24-43
LINE LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL................14-74
LINER - INSTALLATION, REAR
WHEELHOUSE.......................23-96
LINER - REMOVAL, REAR WHEELHOUSE . . 23-96
LINES - CLEANING AND INSPECTION,
OIL COOLER........................9-296
LINES - DESCRIPTION, FUEL.......14-73,14-9
LINES - DESCRIPTION, HIGH PRESSURE
FUEL..............................14-74
LINES - INSTALLATION, FUEL...........14-77
LINES - OPERATION, HIGH PRESSURE
FUEL..............................14-74
LINES - REMOVAL, FUEL..............14-75
LINES/HOSES - INSPECTION.............30-6
LINK CONNECTOR - DESCRIPTION, DATA . 8E-12
LINK CONNECTOR - OPERATION, DATA . . . 8E-12
LINKAGE - 2WD - DESCRIPTION........19-38
LINKAGE - 2WD - INSTALLATION........19-39
LINKAGE - 2WD - REMOVAL
............19-38
LINKAGE - 4WD - DESCRIPTION
........19-40
LINKAGE - 4WD - INSTALLATION
........19-41
LINKAGE - 4WD - REMOVAL
............19-40
LINKAGE - DESCRIPTION
...............6-19LINKAGE - INSTALLATION...............6-20
LINKAGE - OPERATION.................6-20
LINKAGE - REMOVAL..................6-20
LINKAGE, SPECIAL TOOLS - STEERING . . . 19-39,
19-42
LINK/COIL SUSPENSION - STANDARD
PROCEDURES, ALIGNMENT..............2-5
LINK/COIL SUSPENSION, SPECIAL
TOOLS..............................2-16
LIQUID LINE - INSTALLATION...........24-52
LIQUID LINE - REMOVAL..............24-52
LOAD TEST - STANDARD PROCEDURE....8F-14
LOADS - STANDARD PROCEDURE,
TESTING FOR SHORT TO GROUND ON
FUSES POWERING SEVERAL.........8W-01-7
LOCATIONS - DESCRIPTION, SPLICE . . . 8W-95-1
LOCATIONS, SPECIFICATIONS - BODY
SEALER............................23-47
LOCATIONS, SPECIFICATIONS -
STRUCTURAL ADHESIVE...............23-44
LOCATIONS, SPECIFICATIONS - WELD.....23-4
LOCK & REMOTE KEYLESS ENTRY
SYSTEM - DIAGNOSIS AND TESTING,
POWER.............................8N-4
LOCK - STANDARD PROCEDURE,
HYDROSTATIC.....9-11,9-125,9-181,9-238,9-68
LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH AND KEY....19-10
LOCK CYLINDER - INSTALLATION.......23-73
LOCK CYLINDER - REMOVAL...........23-73
LOCK CYLINDER HOUSING -
INSTALLATION.......................19-11
LOCK CYLINDER HOUSING - REMOVAL . . . 19-10
LOCK CYLINDERS - DESCRIPTION........23-1
LOCK MOTOR - DESCRIPTION, POWER....8N-6
LOCK MOTOR - DIAGNOSIS AND
TESTING, POWER.....................8N-7
LOCK MOTOR - OPERATION, POWER.....8N-6
LOCK SWITCH - DESCRIPTION, DOOR
CYLINDER...........................8N-5
LOCK SWITCH - DESCRIPTION, POWER . . . 8N-8
LOCK SWITCH - DIAGNOSIS & TESTING,
DOOR CYLINDER.....................8N-5
LOCK SWITCH - DIAGNOSIS AND
TESTING, POWER.....................8N-8
LOCK SWITCH - INSTALLATION, DOOR
CYLINDER...........................8N-6
LOCK SWITCH - OPERATION, DOOR
CYLINDER...........................8N-5
LOCK SWITCH - OPERATION, POWER.....8N-8
LOCK SWITCH - REMOVAL, DOOR
CYLINDER...........................8N-6
LOCK SYSTEM - DESCRIPTION, POWER . . . 8N-1
LOCK SYSTEM - DIAGNOSIS AND
TESTING, POWER.....................8N-4
LOCK SYSTEM - OPERATION, POWER.....8N-3
LOCKS - INSPECTION, DOORS AND
DOOR.............................30-11
LOCKS - INSPECTION, WINDOWS,
DOORS............................30-14
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-29
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-29
LOOP HEIGHT ADJUSTER KNOB -
INSTALLATION, TURNING..............8O-30
LOOP HEIGHT ADJUSTER KNOB -
REMOVAL, TURNING.................8O-30
LOOSE ITEMS - INSTALLATION, SHIPPED . 30-14
LOW FUEL INDICATOR - DESCRIPTION . . . 8J-23
LOW FUEL INDICATOR - OPERATION.....8J-23
LOW MOUNTED - INSTALLATION, SIDE
VIEW MIRROR.......................23-98
LOW MOUNTED - REMOVAL, SIDE VIEW
MIRROR...........................23-98
LOW PRESSURE SWITCH -
DESCRIPTION, A/C...................24-21
LOW PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C...................24-21
LOW PRESSURE SWITCH -
INSTALLATION, A/C
...................24-22
LOW PRESSURE SWITCH - OPERATION,
A/C
................................24-21
LOW PRESSURE SWITCH - REMOVAL,
A/C
................................24-21
LOWER - INSTALLATION, LATCH
........23-80
LOWER - INSTALLATION, LATCH
STRIKER
...........................23-82LOWER - REMOVAL, LATCH............23-80
LOWER - REMOVAL, LATCH STRIKER....23-82
LOWER BALL JOINT - DIAGNOSIS AND
TESTING............................2-10
LOWER BALL JOINT - INSTALLATION......2-25
LOWER CONTROL ARM - INSTALLATION . . 2-10,
2-20
LOWER CONTROL ARM - REMOVAL . . 2-10,2-20
LOWER FASCIA - INSTALLATION, FRONT . . . 13-3
LOWER FASCIA - REMOVAL, FRONT......13-3
LUBRICANTS - STANDARD PROCEDURE,
CLASSIFICATION OF....................0-3
LUBRICATION - DESCRIPTION.....9-102,9-158,
9-214,9-292,9-45
LUBRICATION - DIAGNOSIS AND
TESTING...............9-123,9-178,9-66,9-8
LUBRICATION - OPERATION . 9-102,9-158,9-214,
9-292,9-45
LUBRICATION - STANDARD PROCEDURE . 19-38,
19-40
LUMBAR ADJUSTER - DIAGNOSIS &
TESTING, POWER....................8N-18
LUMBAR CONTROL SWITCH -
DESCRIPTION.......................8N-17
LUMBAR CONTROL SWITCH -
OPERATION.........................8N-18
LUMBAR CONTROL SWITCH - REMOVAL . 8N-18
LUMBAR MOTOR - DESCRIPTION.......8N-18
LUMBAR MOTOR - OPERATION.........8N-18
LUMBAR SUPPORT - INSTALLATION....23-133
LUMBAR SUPPORT - REMOVAL........23-133
MACHINING - STANDARD PROCEDURE,
BRAKE DRUM........................5-33
MAIN BEARING CLEARANCE -
STANDARD PROCEDURE...............9-275
MAIN BEARING FITTING - STANDARD
PROCEDURE....................9-203,9-33
MAIN BEARING FITTING - STANDARD
PROCEDURE, CRANKSHAFT........9-146,9-90
MAIN BEARINGS - DESCRIPTION,
CRANKSHAFT...............9-146,9-32,9-90
MAIN BEARINGS - INSTALLATION,
CRANKSHAFT..........9-147,9-204,9-34,9-90
MAIN BEARINGS - OPERATION,
CRANKSHAFT...............9-146,9-32,9-90
MAIN BEARINGS - REMOVAL,
CRANKSHAFT..........9-147,9-204,9-33,9-90
MAINTENANCE SCHEDULE (8.0L 2500 &
3500 MODELS - CALIFORNIA ONLY) -
DESCRIPTION, MEDIUM DUTY TRUCK.....0-13
MAINTENANCE SCHEDULES - 24-VALVE
CUMMINS TURBO DIESEL -
DESCRIPTION........................0-22
MAINTENANCE SCHEDULES -
DESCRIPTION, HEAVY DUTY ENGINE
(FEDERAL ONLY - 2500 8.0L HD AND
3500 5.9L& 8.0L MODELS)..............0-17
MAINTENANCE SCHEDULES - LIGHT
DUTY ENGINE (1500 AND 2500
MODELS EXCEPT 8.0L) MAINTENANCE
SCHEDULES..........................0-7
MAINTENANCE SCHEDULES,
MAINTENANCE SCHEDULES - LIGHT
DUTY ENGINE (1500 AND 2500
MODELS EXCEPT 8.0L)..................0-7
MALFUNCTION INDICATOR LAMP (MIL) -
DESCRIPTION.......................8J-24
MALFUNCTION INDICATOR LAMP (MIL) -
OPERATION.........................8J-24
MANAGER - DESCRIPTION, TASK........25-15
MANAGER - OPERATION, TASK.........25-19
MANIFOLD - CLEANING, EXHAUST . 9-112,9-168,
9-225,9-304,9-55
MANIFOLD - CLEANING, INTAKE . . . 9-110,9-166,
9-223,9-302,9-53
MANIFOLD - DESCRIPTION, EXHAUST . . . 9-112,
9-168,9-224,9-55
MANIFOLD - DESCRIPTION, FUEL DRAIN . . 14-86
MANIFOLD - DESCRIPTION, INTAKE
.....9-109,
9-165,9-222,9-52
MANIFOLD - INSPECTION, EXHAUST
.....9-112,
9-168,9-225,9-304,9-55
MANIFOLD - INSPECTION, INTAKE
. 9-110,9-166,
9-223,9-302,9-53
MANIFOLD - INSTALLATION, EXHAUST
. . . 9-113,
9-168,9-225,9-304,9-55
MANIFOLD - INSTALLATION, FUEL
DRAIN
.............................14-86
BR/BEINDEX 21
Description Group-Page Description Group-Page Description Group-Page

SPECIFICATIONS, SPECIFICATIONS -
TORQUE............................23-61
SPECIFICATIONS, SPECIFICATIONS -
TORQUE............................13-9
SPECIFICATIONS, SPECIFICATIONS -
TORQUE............................24-8
SPECIFICATIONS, TORQUE - FUEL
DELIVERY...........................14-4
SPECIFICATIONS, TORQUE - GAS FUEL
INJECTION..........................14-35
SPECIFICATIONS, TORQUE -
GENERATOR/CHARGING SYSTEM........8F-28
SPECIFICATIONS, TORQUE - IGNITION.....8I-2
SPECIFICATIONS, TORQUE - STARTING
SYSTEM............................8F-38
SPEED CONTROL - INSPECTION.........30-17
SPEED CONTROL SERVO - DESCRIPTION . . 8P-5
SPEED CONTROL SERVO -
INSTALLATION.......................8P-10
SPEED CONTROL SERVO - OPERATION....8P-5
SPEED CONTROL SERVO - REMOVAL.....8P-6
SPEED CONTROL SYSTEM -
DESCRIPTION........................8P-1
SPEED CONTROL SYSTEM - OPERATION . . . 8P-2
SPEED CONTROL SYSTEM - TORQUE.....8P-4
SPEED INPUT - DESCRIPTION, VEHICLE . . . 8P-1
SPEED SENSOR - DESCRIPTION . 21-253,21-424,
21-597,21-770
SPEED SENSOR - OPERATION . . . 21-253,21-424,
21-597,21-770
SPEEDOMETER - DESCRIPTION...........8J-30
SPEEDOMETER - OPERATION...........8J-30
SPLASH SHIELD - INSTALLATION, REAR . . 23-96
SPLASH SHIELD - REMOVAL, REAR......23-96
SPLASH SHIELDS - INSTALLATION,
FRONT END.........................23-92
SPLASH SHIELDS - REMOVAL, FRONT
END ...............................23-92
SPLICE LOCATIONS - DESCRIPTION . . . 8W-95-1
SPLICING - STANDARD PROCEDURE,
WIRE...........................8W-01-12
SPLIT BENCH - INSTALLATION, SEAT....23-134
SPLIT BENCH - INSTALLATION, SEAT
BACK.............................23-136
SPLIT BENCH - INSTALLATION, SEAT
BACK COVER.......................23-138
SPLIT BENCH - INSTALLATION, SEAT
CUSHION COVER....................23-140
SPLIT BENCH - INSTALLATION, SEAT
TRACK............................23-142
SPLIT BENCH - REMOVAL, SEAT.......23-134
SPLIT BENCH - REMOVAL, SEAT BACK . . 23-135
SPLIT BENCH - REMOVAL, SEAT BACK
COVER............................23-137
SPLIT BENCH - REMOVAL, SEAT
CUSHION COVER....................23-139
SPLIT BENCH - REMOVAL, SEAT TRACK . 23-142
SPOOL VALVE - INSTALLATION..........19-26
SPOOL VALVE - REMOVAL.............19-24
SPRING - DESCRIPTION........2-11,2-22,2-28
SPRING - INSTALLATION.......2-12,2-22,2-29
SPRING - OPERATION..........2-11,2-22,2-28
SPRING - REMOVAL...........2-11,2-22,2-28
SPRING AND SHOCK - DIAGNOSIS AND
TESTING............................2-26
SPRINGS - INSTALLATION, VALVES AND
VALVE .............................9-199
SPRINGS - REMOVAL, VALVES AND
VALVE .............................9-197
SPRINGS - STANDARD PROCEDURE,
VALVES, GUIDES.............9-138,9-25,9-82
SPRINGS, INTAKE/EXHAUST VALVES &
SEATS - STANDARD PROCEDURE-
VALVES,GUIDES.....................9-253
SPROCKETS - INSTALLATION, TIMING
BELT/CHAIN...........9-115,9-170,9-227,9-58
SPROCKETS - REMOVAL, TIMING
BELT/CHAIN...........9-114,9-170,9-226,9-57
SQUEAKS, RATTLES AND WIND NOISE -
INSPECTION........................30-15
STABILIZER BAR - DESCRIPTION . 2-12,2-22,2-30
STABILIZER BAR - INSTALLATION....2-12,2-23,
2-30
STABILIZER BAR - OPERATION
. . 2-12,2-22,2-30
STABILIZER BAR - REMOVAL
....2-12,2-22,2-30
STANCHION COVER - INSTALLATION
....23-143
STANCHION COVER - REMOVAL
........23-143
STANDARD CAB - INSTALLATION
........8O-19STANDARD CAB - REMOVAL...........8O-18
STARTER MOTOR - DESCRIPTION,
ENGINE............................8F-39
STARTER MOTOR - DIAGNOSIS AND
TESTING...........................8F-39
STARTER MOTOR - INSTALLATION,
ENGINE............................8F-41
STARTER MOTOR - OPERATION, ENGINE . . 8F-39
STARTER MOTOR - REMOVAL, ENGINE . . . 8F-40
STARTER MOTOR RELAY -
DESCRIPTION, ENGINE................8F-42
STARTER MOTOR RELAY -
INSTALLATION, ENGINE................8F-43
STARTER MOTOR RELAY - OPERATION,
ENGINE............................8F-42
STARTER MOTOR RELAY - REMOVAL,
ENGINE............................8F-43
STARTER RELAY - DIAGNOSIS AND
TESTING...........................8F-42
STARTING - DESCRIPTION.............8F-32
STARTING - OPERATION...............8F-32
STARTING - STANDARD PROCEDURE,
JUMP...............................0-27
STARTING SYSTEM - DIAGNOSIS AND
TESTING...........................8F-33
STARTING SYSTEM - SPECIFICATIONS,
TORQUE............................8F-38
STARTING SYSTEM, SPECIFICATIONS.....8F-38
STATE DISPLAY TEST MODE -
DESCRIPTION........................25-1
STATIONARY GLASS - DESCRIPTION....23-145
STATIONARY GLASS - OPERATION......23-145
STEERING - DESCRIPTION..............19-1
STEERING - OPERATION................19-1
STEERING AND HANDLING -
INSPECTION........................30-15
STEERING COLUMN OPENING COVER -
INSTALLATION......................23-116
STEERING COLUMN OPENING COVER -
REMOVAL.........................23-115
STEERING FLOW AND PRESSURE -
DIAGNOSIS AND TESTING, POWER.......19-4
STEERING GEAR HOUSING PLUG -
INSTALLATION.......................19-27
STEERING GEAR HOUSING PLUG -
REMOVAL..........................19-27
STEERING GEAR LEAKAGE - DIAGNOSIS
AND TESTING, POWER................19-14
STEERING GEAR, SPECIAL TOOLS -
POWER............................19-20
STEERING GEAR, SPECIFICATIONS -
POWER............................19-19
STEERING LINKAGE, SPECIAL TOOLS....19-39,
19-42
STEERING PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER.......19-31
STEERING PUMP, SPECIAL TOOLS -
POWER............................19-36
STEERING SYSTEM - DIAGNOSIS AND
TESTING, POWER.....................19-2
STEERING SYSTEM - STANDARD
PROCEDURE, FLUSHING POWER........19-32
STEERING WHEEL - INSTALLATION......19-13
STEERING WHEEL - REMOVAL..........19-13
STEM SEAL - INSTALLATION, VALVE.....9-198
STEM SEALS - REMOVAL, VALVE........9-197
STEPS - NEW VEHICLE PREPARATION
FORM, FINAL........................30-22
STOP LAMP - INSTALLATION, CENTER
HIGH MOUNTED......................8L-6
STOP LAMP - REMOVAL, CENTER HIGH
MOUNTED...........................8L-6
STOP LAMP UNIT - INSTALLATION,
CENTER HIGH MOUNTED...............8L-6
STOP LAMP UNIT - REMOVAL, CENTER
HIGH MOUNTED......................8L-6
STORAGE - DESCRIPTION, PRE
DELIVERY..........................30-19
STORAGE - STANDARD PROCEDURE,
PRE DELIVERY......................30-20
STORAGE BIN - INSTALLATION
.........23-116
STORAGE BIN - REMOVAL
............23-116
STOWAGE TRAY - INSTALLATION, REAR
FLOOR
............................23-121
STOWAGE TRAY - REMOVAL, REAR
FLOOR
............................23-121
STRAP - INSTALLATION, CAB-TO- BED
GROUND
...........................8A-14STRAP - INSTALLATION, ENGINE-TO-
BODY GROUND......................8A-13
STRAP - INSTALLATION, HEATER CORE
GROUND...........................8A-15
STRAP - REMOVAL, CAB-TO- BED
GROUND...........................8A-14
STRAP - REMOVAL, ENGINE-TO-BODY
GROUND...........................8A-13
STRAP - REMOVAL, HEATER CORE
GROUND...........................8A-14
STRETCH - INSPECTION, MEASURING
TIMING CHAIN........9-114,9-170,9-227,9-58
STRIKER - ADJUSTMENT, LATCH.......23-102
STRIKER - INSTALLATION, GLOVE BOX
LATCH ............................23-113
STRIKER - INSTALLATION, LATCH . 23-102,23-65,
23-73
STRIKER - LOWER - INSTALLATION,
LATCH .............................23-82
STRIKER - LOWER - REMOVAL, LATCH . . . 23-82
STRIKER - REMOVAL, GLOVE BOX
LATCH ............................23-113
STRIKER - REMOVAL, LATCH....23-102,23-65,
23-73
STRIKER - UPPER - INSTALLATION,
LATCH .............................23-82
STRIKER - UPPER - REMOVAL, LATCH . . . 23-82
STRIPE - INSTALLATION, TAPE..........23-88
STRIPE - REMOVAL, TAPE.............23-88
STRIPES AND DECALS - INSTALLATION,
BODY..............................23-87
STRIPES AND DECALS - REMOVAL,
BODY..............................23-87
STRUCTURAL ADHESIVE LOCATIONS,
SPECIFICATIONS.....................23-44
STUDS - INSTALLATION...............22-12
STUDS - REMOVAL...................22-12
SUCTION AND DISCHARGE LINE -
INSTALLATION.......................24-51
SUCTION AND DISCHARGE LINE -
REMOVAL..........................24-50
SUN VISOR - INSTALLATION..........23-127
SUN VISOR - REMOVAL..............23-127
SUPPLIES - DESCRIPTION, 5 VOLT......8E-17
SUPPLIES - OPERATION, 5 VOLT........8E-19
SUPPLY - DIAGNOSIS AND TESTING,
VACUUM............................8P-2
SUPPLY RESTRICTIONS - DIAGNOSIS
AND TESTING, FUEL..................14-56
SUPPORT - INSTALLATION, LUMBAR....23-133
SUPPORT - REMOVAL, LUMBAR.......23-133
SUPPORT BRACKET - INSTALLATION,
REARVIEW MIRROR.................23-126
SUPPORT PLATE - INSTALLATION........5-32
SUPPORT PLATE - REMOVAL............5-32
SUPPRESSION COMPONENTS -
DESCRIPTION, RADIO NOISE...........8A-12
SUPPRESSION COMPONENTS -
DIAGNOSIS AND TESTING, RADIO
NOISE.............................8A-12
SUSPENSION - STANDARD
PROCEDURES, ALIGNMENT LINK/COIL.....2-5
SUSPENSION, SPECIAL TOOLS -
INDEPENDENT FRONT...................2-9
SUSPENSION, SPECIAL TOOLS -
LINK/COIL...........................2-16
SUSPENSION-REAR, SPECIAL TOOLS.....2-28
SWITCH - DESCRIPTION
...............8P-12
SWITCH - DESCRIPTION, A/C HIGH
PRESSURE
.........................24-20
SWITCH - DESCRIPTION, A/C LOW
PRESSURE
.........................24-21
SWITCH - DESCRIPTION, BLOWER
MOTOR
............................24-24
SWITCH - DESCRIPTION, BRAKE LAMP
....8L-4
SWITCH - DESCRIPTION, CLUTCH
PEDAL POSITION
.....................6-22
SWITCH - DESCRIPTION, DOOR AJAR
....8L-34
SWITCH - DESCRIPTION, DOOR
CYLINDER LOCK
......................8N-5
SWITCH - DESCRIPTION, DRIVER
POWER SEAT
.......................8N-16
SWITCH - DESCRIPTION, DRIVER SEAT
HEATER
.............................8G-7
SWITCH - DESCRIPTION, HEADLAMP
....8L-18
SWITCH - DESCRIPTION, HORN
..........8H-4
SWITCH - DESCRIPTION, IGNITION
......19-11
BR/BEINDEX 33
Description Group-Page Description Group-Page Description Group-Page

TANK MODULE - DESCRIPTION, FUEL....14-78
TANK MODULE - INSTALLATION, FUEL....14-79
TANK MODULE - OPERATION, FUEL......14-78
TANK MODULE - REMOVAL, FUEL.......14-78
TAPE STRIPE - INSTALLATION..........23-88
TAPE STRIPE - REMOVAL..............23-88
TAPPETS - DIAGNOSIS AND TESTING,
HYDRAULIC............9-151,9-206,9-38,9-95
TASK MANAGER - DESCRIPTION........25-15
TASK MANAGER - OPERATION..........25-19
TEMP SENSOR - 3.9L/5.2L/5.9L -
DESCRIPTION, ENGINE COOLANT.........7-48
TEMP SENSOR - 3.9L/5.2L/5.9L -
INSTALLATION, ENGINE COOLANT........7-48
TEMP SENSOR - 3.9L/5.2L/5.9L -
OPERATION, ENGINE COOLANT..........7-48
TEMP SENSOR - 3.9L/5.2L/5.9L -
REMOVAL, ENGINE COOLANT............7-48
TEMP SENSOR - DESCRIPTION,
AMBIENT..........................8M-11
TEMP SENSOR - INSTALLATION,
AMBIENT..........................8M-13
TEMP SENSOR - OPERATION, AMBIENT . . 8M-11
TEMP SENSOR - REMOVAL, AMBIENT . . . 8M-12
TEMPERATURE GAUGE - DESCRIPTION,
ENGINE............................8J-19
TEMPERATURE GAUGE - OPERATION,
ENGINE............................8J-19
TEMPERATURE SENSOR - DESCRIPTION,
BATTERY...........................8F-29
TEMPERATURE SENSOR - DESCRIPTION,
FUEL..............................14-99
TEMPERATURE SENSOR - DESCRIPTION,
TRANSMISSION . . . 21-262,21-433,21-606,21-779
TEMPERATURE SENSOR - DIAGNOSIS &
TESTING, AMBIENT..................8M-12
TEMPERATURE SENSOR -
INSTALLATION, BATTERY..............8F-29
TEMPERATURE SENSOR - OPERATION,
BATTERY...........................8F-29
TEMPERATURE SENSOR - OPERATION,
FUEL.............................14-100
TEMPERATURE SENSOR - OPERATION,
TRANSMISSION . . . 21-262,21-433,21-606,21-779
TEMPERATURE SENSOR - REMOVAL,
BATTERY...........................8F-29
TENSIONER - ADJUSTMENT, CABLE.......5-40
TENSIONER - DESCRIPTION, TIMING
BELT/CHAIN..........................9-57
TENSIONER - OPERATION, TIMING
BELT/CHAIN..........................9-57
TENSIONERS - 3.9L/5.2L/5.9L -
DESCRIPTION, BELT...................7-19
TENSIONERS - 3.9L/5.2L/5.9L -
INSTALLATION, BELT...................7-20
TENSIONERS - 3.9L/5.2L/5.9L -
OPERATION, BELT.....................7-19
TENSIONERS - 3.9L/5.2L/5.9L -
REMOVAL, BELT......................7-20
TENSIONERS - 5.9L DIESEL -
DESCRIPTION, BELT...................7-23
TENSIONERS - 5.9L DIESEL -
INSTALLATION, BELT...................7-23
TENSIONERS - 5.9L DIESEL -
OPERATION, BELT.....................7-23
TENSIONERS - 5.9L DIESEL - REMOVAL,
BELT ...............................7-23
TENSIONERS - 8.0L - DESCRIPTION,
BELT ...............................7-20
TENSIONERS - 8.0L - INSTALLATION,
BELT ...............................7-22
TENSIONERS - 8.0L - OPERATION, BELT . . . 7-20
TENSIONERS - 8.0L - REMOVAL, BELT.....7-21
TERMINAL - INSTALLATION.........8W-01-11
TERMINAL - REMOVAL.............8W-01-11
TEST - DIAGNOSIS AND TESTING, FUEL
INJECTOR.....................14-53,14-95
TEST - DIAGNOSIS AND TESTING, FUEL
PRESSURE LEAK DOWN
................14-2
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP AMPERAGE
....................14-10
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP CAPACITY
......................14-9
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP PRESSURE
....................14-10
TEST - DIAGNOSIS AND TESTING,
HYDRAULIC PRESSURE
. . 21-144,21-315,21-487,
21-658TEST - DIAGNOSIS AND TESTING,
POWR-LOKY........................3-161
TEST - DIAGNOSIS AND TESTING, ROAD . . . 8P-3
TEST - INSPECTION WINDSHIELD
WIPERS/WASHERS, ROAD.............30-18
TEST - STANDARD PROCEDURE,
BUILT-IN INDICATOR..................8F-11
TEST - STANDARD PROCEDURE,
HYDROMETER.......................8F-12
TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW..................8F-15
TEST - STANDARD PROCEDURE, LOAD . . . 8F-14
TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE...............8F-13
TEST - STANDARD PROCEDURE,
VERIFICATION........................8O-5
TEST INSPECTION - DESCRIPTION,
ROAD..............................30-15
TEST MODE - DESCRIPTION, CIRCUIT
ACTUATION..........................25-1
TEST MODE - DESCRIPTION, STATE
DISPLAY............................25-1
TETHER - INSTALLATION, CHILD.........8O-9
TETHER - REMOVAL, CHILD.............8O-9
THEFT SECURITY - DESCRIPTION,
VEHICLE............................8Q-1
THEFT SECURITY - OPERATION, VEHICLE . . 8Q-2
THEFT SECURITY SYSTEM - DIAGNOSIS
AND TESTING, VEHICLE................8Q-3
THERMOSTAT - 3.9L/5.2L/5.9L -
DESCRIPTION, ENGINE COOLANT.........7-49
THERMOSTAT - 3.9L/5.2L/5.9L -
INSTALLATION, ENGINE COOLANT........7-50
THERMOSTAT - 3.9L/5.2L/5.9L -
OPERATION, ENGINE COOLANT..........7-49
THERMOSTAT - 3.9L/5.2L/5.9L -
REMOVAL, ENGINE COOLANT............7-49
THERMOSTAT - 5.9L DIESEL -
DESCRIPTION, ENGINE COOLANT.........7-54
THERMOSTAT - 5.9L DIESEL -
INSTALLATION, ENGINE COOLANT........7-55
THERMOSTAT - 5.9L DIESEL -
OPERATION, ENGINE COOLANT..........7-54
THERMOSTAT - 5.9L DIESEL -
REMOVAL, ENGINE COOLANT............7-55
THERMOSTAT - 8.0L - DESCRIPTION,
ENGINE COOLANT.....................7-52
THERMOSTAT - 8.0L - INSTALLATION,
ENGINE COOLANT.....................7-53
THERMOSTAT - 8.0L - OPERATION,
ENGINE COOLANT.....................7-52
THERMOSTAT - 8.0L - REMOVAL,
ENGINE COOLANT.....................7-52
THERMOSTAT - DIAGNOSIS AND
TESTING....................7-49,7-52,7-54
THOMAS AND BETTS - INSTALLATION,
CONNECTOR.....................8W-01-10
THOMAS AND BETTS - REMOVAL,
CONNECTOR......................8W-01-9
THREAD REPAIR - STANDARD
PROCEDURE, ALUMINUM......21-159,21-330,
21-502,21-673
THREADED HOLE REPAIR -
DESCRIPTION......................Intro.-6
THREADS - STANDARD PROCEDURE,
REPAIR DAMAGED OR WORN . 9-11,9-125,9-181,
9-238,9-68
THROTTLE BODY - DESCRIPTION........14-48
THROTTLE BODY - OPERATION.........14-48
THROTTLE CONTROL CABLE -
INSTALLATION.................14-105,14-50
THROTTLE CONTROL CABLE -
REMOVAL....................14-104,14-50
THROTTLE POSITION SENSOR -
DESCRIPTION.......................14-51
THROTTLE POSITION SENSOR -
OPERATION.........................14-51
THROTTLE VALVE CABLE -
ADJUSTMENTS, TRANSMISSION
. 21-254,21-425,
21-598,21-771
THROTTLE VALVE CABLE -
DESCRIPTION
....21-253,21-424,21-597,21-770
TIMER MODULE - DESCRIPTION, BODY
CONTROL/CENTRAL
...................8E-1
TIMER MODULE - DIAGNOSIS AND
TESTING, CENTRAL
....................8E-4
TIMER MODULE - INSTALLATION, BODY
CONTROL/CENTRAL
...................8E-6TIMER MODULE - OPERATION, BODY
CONTROL/CENTRAL...................8E-3
TIMER MODULE - REMOVAL, BODY
CONTROL/CENTRAL...................8E-5
TIMING - DIAGNOSIS AND TESTING,
FUEL INJECTION PUMP...............14-66
TIMING BELT / CHAIN COVER(S) -
INSTALLATION........9-113,9-169,9-226,9-56
TIMING BELT / CHAIN COVER(S) -
REMOVAL............9-113,9-169,9-225,9-56
TIMING BELT/CHAIN AND SPROCKETS -
INSTALLATION........9-115,9-170,9-227,9-58
TIMING BELT/CHAIN AND SPROCKETS -
REMOVAL............9-114,9-170,9-226,9-57
TIMING BELT/CHAIN TENSIONER -
DESCRIPTION........................9-57
TIMING BELT/CHAIN TENSIONER -
OPERATION..........................9-57
TIMING CHAIN STRETCH - INSPECTION,
MEASURING..........9-114,9-170,9-227,9-58
TIMING, SPECIFICATIONS - IGNITION......8I-3
TIPS - CLEANING, APPEARANCE........30-21
TIRE - DESCRIPTION, SPARE............22-9
TIRE AND WHEEL BALANCE -
STANDARD PROCEDURES...............22-4
TIRE AND WHEEL RUNOUT - DIAGNOSIS
AND TESTING........................22-1
TIRE NOISE OR VIBRATION - DIAGNOSIS
AND TESTING........................22-8
TIRE PRESSURES - INSPECTION.........30-8
TIRE REVOLUTIONS PER MILE,
SPECIFICATIONS......................22-9
TIRE ROTATION - STANDARD
PROCEDURES........................22-2
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING........................22-7
TIRE WINCH - INSTALLATION, SPARE....13-10
TIRE WINCH - REMOVAL, SPARE........13-10
TIRES - DESCRIPTION.............22-5,22-6
TO GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT.............8W-01-6
TO GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR SHORT....8W-01-7
TO OIL COOLER - INSTALLATION, AIR.....7-88
TO OIL COOLER - REMOVAL, AIR.........7-87
TO OIL COOLER - REMOVAL, WATER......7-87
TO USE WIRING DIAGRAMS -
DESCRIPTION, HOW................8W-01-1
TOOLS - 5.2L ENGINE, SPECIAL..........9-77
TOOLS - 5.9L DIESEL ENGINE, SPECIAL . . 9-244
TOOLS - 5.9L ENGINE, SPECIAL.........9-134
TOOLS - 8.0L ENGINE, SPECIAL.........9-188
TOOLS - AUDIO SYSTEMS, SPECIAL......8A-4
TOOLS - BASE BRAKES, SPECIAL.........5-4
TOOLS - COOLING, SPECIAL.............7-18
TOOLS - DIESEL FUEL SYSTEM,
SPECIAL...........................14-59
TOOLS - FRONT AXLE, SPECIAL..........3-58
TOOLS - FRONT AXLES, SPECIAL.........3-25
TOOLS - FUEL SYSTEM, SPECIAL . . . 14-36,14-4
TOOLS - HEADLAMP ALIGNMENT,
SPECIAL............................8L-4
TOOLS - INDEPENDENT FRONT
SUSPENSION, SPECIAL..................2-9
TOOLS - LINK/COIL SUSPENSION,
SPECIAL
............................2-16
TOOLS - NV5600 MANUAL
TRANSMISSION, SPECIAL
.............21-127
TOOLS - OVERHEAD CONSOLE
SYSTEMS, SPECIAL
...................8M-8
TOOLS - POWER DISTRIBUTION
SYSTEMS, SPECIAL
................8W-97-2
TOOLS - POWER STEERING GEAR,
SPECIAL
...........................19-20
TOOLS - POWER STEERING PUMP,
SPECIAL
...........................19-36
TOOLS - PROPELLER SHAFT, SPECIAL
......3-8
TOOLS - RE TRANSMISSION, SPECIAL
. . 21-534,
21-704
TOOLS - RE TRANSMISSIONS, SPECIAL
. 21-188,
21-359
TOOLS - STEERING LINKAGE, SPECIAL
. . . 19-39,
19-42
TOOLS - SUSPENSION-REAR, SPECIAL
....2-28
TOOLS, AIRBAG SYSTEM - SPECIAL
......8O-6
TOOLS, WIRING/TERMINAL - SPECIAL
. 8W-01-8
BR/BEINDEX 35
Description Group-Page Description Group-Page Description Group-Page