2000 TOYOTA CAMRY child lock

IN04Q±03
IN±36
± INTRODUCTIONTERMS
36 Author: Date:
TERMS
ABBREVIATIONS USED IN THIS MANUAL
AbbreviationsMeaning
ABSAnti±Lock Brake System
ACAlternating Current
ACCAccessory
ACISAcoustic Control Induction System
ACSDAutomatic Cold Start Device
A.D.D.Automatic Disconnecting Differential
A/FAir±Fuel Ratio
AHCActive Height Control Suspension
ALRAutomatic Locking Retractor
ALTAlternator
AMPAmplifier
ANTAntenna
APPROX.Approximately
A/TAutomatic Transmission (Transaxle)
AT FAutomatic Transmission Fluid
AUTOAutomatic
AUXAuxiliary
AV GAverage
AV SAdaptive Variable Suspension
BACSBoost Altitude Compensation System
BATBattery
BDCBottom Dead Center
B/LBi±Level
B/SBore±Stroke Ratio
BTDCBefore Top Dead Center
BVSVBimetallic Vacuum Switching Valve
Calif.California
CBCircuit Breaker
CCoCatalytic Converter For Oxidation
CDCompact Disc
CFCornering Force
CGCenter Of Gravity
CHChannel
COMB.Combination
CPECoupe
CPSCombustion Pressure Sensor
CPUCentral Processing Unit
CRSChild Restraint System
CTRCenter
C/VCheck Valve
CVControl Valve
CWCurb Weight

SS±70
± SERVICE SPECIFICATIONSBODY
233 Author: Date:
Front seat inner upper track x Seat cushion1818513
Side Airbag assembly x Seatback frame1818513
Seatback assembly x Seat cushion frame6.06153 in.´lbf
Front Seat (Power Seat for TMMK Made)±±±
Side airbag assembly x Seat cushion frame6.06153 in.´lbf
Front Seat (Manual Seat for TMC Made)±±±
Side airbag assembly x Seat cushion frame6.06153 in.´lbf
Rear Seat (TMC Made)±±±
Seatback hinge x Body1818513
Rear seatback lock control x Rear seatback frame17.517812.5
Rear Seat (TMMK Made)±±±
Seatback pad (RH bolt) x Body7.87969 in.´lbf
Seatback pad (center bolt) x Body4242831
Child restraint seat x Body131309
Seatback hinge x Body1818513
Rear seatback lock control x Rear seatback frame17.517812.5
SEAT BELT±±±
Front Seat belt±±±
Shoulder anchor x Adjustable anchor4242031
Adjustable anchor x Body4242031
Inner belt x Seat4242031
Retractor x Body7.87969 in.´lbf
Floor anchor x Body4242031
Rear Seat Belt±±±
Lap outer belt anchor x Body4242031
ELR x Body4242031
Inner belt x Body4242031
Center belt x Body4242031

SEAT BELT EXTENDER: '98 ± '00 ± BO002±00 January 21, 2000
Page 6 of 7
Failure to follow the recommendations indicated below could result in less effectiveness
of the seat belt restraint system in case of vehicle collision, causing personal injury.
The Seat Belt Extender must not be used:
A. By anyone other than for whom it was provided (name recorded on seat belt
extender).
B. In any vehicle and/or seat position other than the one for which it was provided.
C. When the Seat Belt Extender is provided for rear seat positions (with automatic
locking retractor), make sure the retractor is locked when in use.
If your seat belt cannot be fastened securely because it is not long enough, a
personalized seat belt extender is available from your Toyota dealer free of charge.
Please contact your local Toyota dealer so that the dealer can order the proper required
length for the extender. Bring the heaviest coat you expect to wear for proper
measurement and selection of length. Additional ordering information is available at your
Toyota dealer.
CAUTION:
When using the seat belt extender, observe the following. Failure to follow these
instructions could result in less effectiveness of the seat belt restraint system in case
of vehicle accident, increasing the chance of personal injury.
Never use the Seat Belt Extender if you can COMFORTABLY fasten the seat belt
without it.
The Seat Belt Extender must never be used with any child safety seats.
Remember that the extender provided for you may not be safe when used on a
different vehicle, or for another person or at a different seating position than the
one originally intended for.
To connect the extender to the seat
belt, insert the tab into the seat belt
buckle so that the ªPRESSº signs on
the buckle±release buttons of the
extender and the seat belt are both
facing outward as shown.
You will hear a click when the tab locks
into the buckle.
When releasing the seat belt, press on
the buckle±release button on the
extender, not
on the seat belt. This helps
prevent damage to the vehicle interior
and extender itself.
When not in use, remove the extender and store in the vehicle for future use.
Owner
Instructions
Seat Belt Extender
Seat Belt Release

SEAT BELT EXTENDER: '98 ± '00 ± BO002±00 January 21, 2000
Page 7 of 7
SEAT BELT EXTENDER WORKSHEET
PLEASE COPY THIS ORIGINAL WORKSHEET FOR EACH EXTENDER NEEDED
CAUTIONS:
To minimize the chance and/or severity of injury in an accident, the seat belt
extender must only be used:
1 By the person for whom it was provided
2 In the seat position for which it was provided
The seat belt extender must never be used with any child safety seats.
When the seat belt extender is provided for rear seat positions (with automatic
locking retractor), make sure the retractor is locked when extender belt is in use.
DEALERSEAT BELT EXTENDER APPLICATIONAPPLICANT
DEALER CODEDEALER NAMEAPPLICANT NAME
ADDRESSADDRESS
CITY & STATEZIPCITY & STATEZIPPHONE
EMPLOYEE NAMEMODEL YEARBODY TYPESEATING POSITIONVEHICLE IDENTIFICATION NUMBER
DIRECTIONS FOR DETERMINING PROPER EXTENDER LENGTH
1.Place the seat in the position the applicant normally uses
2.With applicant in the seat, wearing thickest coat expected to be worn, pull belt all the way out and try to buckle
belt
If the belt latches into buckle and feels comfortable against upper chest area, an extender is not needed.
If belt does not buckle continue with step 3
If buckle latches but belt has no slack remaining, continue with step 3
3.Measure distance between applicant's navel and seat belt buckle (dimension A) and enter on worksheet
4.With belt all the way out, measure distance between latch tip and buckle tip (dimension B) and enter on
worksheet
NOTE: If belt latches but there is no slack enter zero as dimension B
5.Subtract dimension B from dimension A and record number in check number box on worksheet
6.Seat belt extender length is dimension B rounded up to next extender length (without exceeding check number)
NOTE: If extender length exceeds check number, an extender can not be provided to the
customer
Dimension A:
NAVEL TO BUCKLEDimension B:
LATCH TO BUCKLE
BuckleBuckle NavelLatch
A
B
SEAT BELT EXTENDER CALCULATION
DIMENSION A:DIMENSION B:CHECK NUMBER:
SEAT BELT EXTENDER AUTHORIZATION
The same seat belt extender can be used for right and left seating applications. Each seat belt extender will have
a label identifying the owner, VIN and seating position. Seat belt extenders are available only in black.
Applicant's Signature: _________________________________________ Date: ______________________
(Actual user of seat belt extender)

SEAT BELT EXTENDER: '99±'01 MODEL YEAR ± BO002-01 January 26, 2001
Page 6 of 7
Failure to follow the recommendations indicated below could result in reduced
effectiveness of the seat belt restraint system in case of vehicle collision, causing
personal injury.
The Seat Belt Extender must not be used:
a. By anyone other than for whom it was provided (name recorded on seat belt
extender).
b. In any vehicle and/or seat position other than the one for which it was provided.
c. When the Seat Belt Extender is provided for rear seat positions (with automatic
locking retractor), make sure the retractor is locked when in use.
If your seat belt cannot be fastened securely because it is not long enough, a
personalized Seat Belt Extender is available from your Toyota dealer free of charge.
Please contact your local Toyota dealer so that the dealer can order the proper required
length for the extender. Bring the heaviest coat you expect to wear for proper
measurement and selection of length. Additional ordering information is available at your
Toyota dealer.
CAUTION:
When using the Seat Belt Extender, observe the following. Failure to follow these
instructions could result in reduced effectiveness of the seat belt restraint system in
case of vehicle accident, increasing the chance of personal injury.
Never use the Seat Belt Extender if you can COMFORTABLY fasten the seat belt
without it.
The Seat Belt Extender must never be used with any child safety seats.
Remember that the extender provided for you may not be safe when used on a
different vehicle, or for another person or at a different seating position than the
one originally intended for.
To connect the extender to the seat
belt, insert the tab into the seat belt
buckle so that the ªPRESSº signs on
the buckle-release buttons of the
extender and the seat belt are both
facing outward as shown.
You will hear a click when the tab locks
into the buckle.
When releasing the seat belt, press on
the buckle-release button on the
extender, not
on the seat belt. This helps
prevent damage to the vehicle interior
and extender itself.
When not in use, remove the extender
and store in the vehicle for future use.
Owner
Instructions
Seat Belt ExtenderSeat Belt Release

Page 7 of 7
PLEASE COPY THIS ORIGINAL WORKSHEET FOR EACH EXTENDER NEEDED
CAUTIONS:
To minimize the chance and/or severity of injury in an accident, the Seat Belt Extender must only be used:
1 By the person for whom it was provided.
2 In the seat position for which it was provided.
The Seat Belt Extender must never be used with any child safety seats.
When the Seat Belt Extender is provided for rear seat positions (with automatic locking retractor),
make sure the retractor is locked when extender belt is in use.
DEALER
SEAT BELT EXTENDER APPLICATIONAPPLICANT
DEALER
CODEDEALER
NAMEAPPLICANT
NAME
ADDRESSADDRESS
CITY
&
STATEZIPCITY
&
STATEZIPPHONE
EMPLOYEE
NAMEMODEL
YEARBODY
TYPESEATING
POSITIONVEHICLE
IDENTIFICATION
NUMBER
DIRECTIONS FOR DETERMINING PROPER EXTENDER LENGTH
1. Place the seat in the position the applicant normally uses.
2. With the applicant in the seat, wearing the thickest coat expected to be worn, pull belt all the way out
and try to buckle belt.
If belt latches into buckle and feels comfortable against upper chest area, an extender is not needed.
If belt does not buckle, continue with Step 3.
If buckle latches but belt has no slack remaining, continue with Step 3.
3. Measure distance between applicant's navel and seat belt buckle (Dimension A) and enter on Worksheet.
4. With belt all the way out, measure distance between latch tip and buckle tip (Dimension B) and enter
on Worksheet.
NOTE: If belt latches but there is no slack enter zero as Dimension B.
5. Subtract Dimension B from Dimension A and record number in Check Number box on Worksheet.
6. Seat Belt Extender length is Dimension B rounded up to next extender length (without exceeding
Check Number).
NOTE: If extender length exceeds Check Number, an extender cannot
be provided to the customer.
Dimension A:
NAVEL TO BUCKLEDimension B:
LATCH TO BUCKLE
BuckleNavel
ABuckle
Latch
B
SEAT BELT EXTENDER CALCULATION
DIMENSION
A:DIMENSION
B:CHECK
NUMBER:
SEAT BELT EXTENDER AUTHORIZATION
The same Seat Belt Extender can be used for right and left seating applications. Each Seat Belt
Extender will have a label identifying the owner, VIN and seating position. Seat Belt Extenders are
available only in black.
Applicant's Signature:
Date:
(Actual user of seat belt extender)

Toyota Supports ASE CertificationPage 1 of 9
BO010-02Title:
CHILD RESTRAINT SEAT TOP STRAP
BRACKET INSTALLATION
Models:
'83 ± '00 All Models
Technical Service
BULLETIN
May 24, 2002

Child restraint seat top strap bracket installation procedures are provided to supplement
the Owner's Manual. Beginning with 2001 models, the top strap brackets are factory
installed.
NOTE:
The child restraint seat top strap assembly is not available as a service part.
Contact the child restraint seat manufacturer for recommended top strap information,
top strap to child restraint seat installation instructions, and top strap retailers.
The top strap brackets can only be installed on vehicles that have nuts welded in
place by the factory. The locations of these nuts can be found in the Owner's Manual
(for most 1983 and newer models.) Toyota does not recommend modifying vehicles
that do not have nuts welded in place by the factory. Some Land Cruiser and RAV4
vehicles, prior to 2001 model year, may not have these nuts welded in by the factory.
Top Strap
Top Strap Bracket
1983 ± 2000 model year vehicles, all models.
PART NUMBERPART NAME
73709±12010Bracket Sub±Assembly (Bracket, Bolt, 10 mm Spacer, and Washers)
04731±22012CRS Kit (two Bolts [15 mm, 30 mm],
three Spacers [5 mm, 10 mm, 15 mm], and Locking Clip)
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty±±±±
BODY
Introduction
Applicable
Vehicles
Parts
Information
Warranty
Information

CHILD RESTRAINT SEAT TOP STRAP BRACKET INSTALLATION ± BO010-02May 24, 2002
Page 2 of 9
Child Restraint Seat Top Strap Bracket Installation
Obtain the exact year and vehicle model Toyota Owner's Manual before beginning
installation.
1. Confirm with the customer which seat
location(s) they will be installing the
child restraint seat. The Owner's
Manual seat section provides an
illustration showing available top strap
bracket location(s). The illustration
page in the Owner's Manual is
provided in pages 4±9 of this bulletin.
NOTE:
Determine which kit parts are needed
for each specific child seat location, by
referring to pages 4±9 of this bulletin.
2. Remove a 20 mm diameter area of
the carpet or trim material above the
bracket mounting location. In some
vehicles, a 20 mm circle is already
pre±cut into the interior trim material.
Once the interior trim material is
removed, the nuts welded in by the
factory should be visible.
3. If a 5 mm or 15 mm spacer is
specified, remove the red lock washer
from the Bracket Sub±Assembly
(P/N 73709±12010) and remove the
10 mm spacer. Assure the red lock
washer is re±installed onto the bolt.
If a 5 mm spacer is needed, use the
15 mm bolt from the CRS Kit
(P/N 04731±22012).
Installation
Procedure
Bolt
Spacer
100 mm
(4.0 in.)
Anchor
Bracket
185 mm
(7.3 in.)345 mm
(13.6 in.)
Example of 1999 Camry Showing Three (3)
Available Bracket Locations
Example of Pre±Cut Circle in Package Tray Finisher
Red Lock Washer Bolt
Wave Washer
Bracket
Nylon Washer
Spacer
(5/10/15 mm)