2000 SUZUKI SWIFT cam

6
6
6-1
6A
6A1
6B
6C
6E1
6E1
6E2
6F
6F
6F1
6G
6H
6K
GENERAL INFORMATION
General Information
Maintenance and Lubrication
1A
1B
TABLE OF CONTENTS SECTION
0A
0B
7B
8
8A
8G HEATING AND AIR CONDITIONING
Heater and Ventilation
Air Conditioning (Oprional)
ENGINE
General Information and Diagnosis
(TBI for G10)
General Information and Diagnosis
(TBI for G13)
General lnformation and Diagnosis
(SFI for G13)
Engine Mechanical (G10 Engine)
Engine Mechanical
(G13 1-cam 16-valves Engine)
Engine Cooling
Engine Fuel
Engine and Emission Control System
(TBI for G10)
Engine and Emission Control System
(TBI for G13)
Engine and Emission Control System
(SFI for G13)
Ignition System (TBI for G10)
Ignition System (TBI for G13)
Ignition System (SFI for G13)
Cranking System
Charging System
Exhaust System
TRANSMISSION, CLUTCH AND
DIFFERENTIAL
Automatic Transmission
BODY ELECTRICAL SYSTEM
Wiring Diagram
IMMOBILIZER CONTROL SYSTEM
1B
0B
0A
1A
6
6B
6C
6E1
6A1
6F
6G
6H
6K
7B
8
8A
8G
6-1
6A
6E2
6F1
6
6E1
6F
NOTE:
The screen toned Section 8A is contained in WIRING DIAGRAM MANUAL mentioned in
RELATED MANUALS.

0A-22 GENERAL INFORMATION
A
ABS : Anti-Lock Brake System
ATDC : After Top Dead Center
API : American Petroleum Institute
ATF : Automatic Transmission Fluid
ALR : Automatic Locking Retractor
AC : Alternating Current
A / T : Automatic Transmission
A / C : Air Conditioning
ABDC : After Bottom Dead Center
A / F : Air Fuel Mixture Ratio
A-ELR : Automatic-Emergency Locking
Retractor
B
B+ : Battery Positive Voltage
BTDC : Before Top Dead Center
BBDC : Before Bottom Dead Center
C
CKT : Circuit
CMP Sensor : Camshaft Position Sensor
(Crank Angle Sensor, CAS)
CO : Carbon Monoxide
CPP Switch : Clutch Pedal Position Switch
(Clutch Switch, Clutch Start
Switch)
CPU : Central Processing Unit
CRS : Child Restraint System
D
DC : Direct Current
DLC : Data Link Connector (Assembly
Line Diag. Link, ALDL, Serial
Data Link, SDL)
DOHC : Double Over Head Camshaft
DOJ : Double Offset Joint
DRL : Daytime Running Light
DTC : Diagnostic Trouble Code
(Diagnostic Code)
E
EBCM : Electronic Brake Control
Module, ABS Control Module
ECM : Engine Control Module
ECT Sensor : Engine Coolant Temperature
Sensor (Water Temp. Sensor,
WTS)
EGR : Exhaust Gas Recirculation
EGRT Sensor : EGR Temperature Sensor
(Recirculated Exhaust
Gas Temp. Sensor, REGTS)
EFE Heater : Early Fuel Evaporation Heater
(Positive Temperature
Coefficient, PTC Heater)
ELR : Emergency Locking Retractor
EPS : Electronic Power Steering
EVAP : Evaporative Emission
EVAP Canister : Evaporative Emission Canister
(Charcoal Canister)
F
4WD : 4 Wheel Drive
G
GEN : Generator
GND : Ground
H
HC : Hydrocarbons
HO2S : Heated Oxygen Sensor
I
IAC Valve : Idle Air Control Valve (Idle
Speed Control Solenoid Valve,
ISC Solenoid Valve)
IAT Sensor : Intake Air Temperature Sensor
(Air temperature Sensor, ATS)
ICM : Immobilizer Control Module
IG : Ignition
ISC Actuator : Idle Speed Control Actuator
(Motor)
ABBREVIATIONS AND SYMBOLS MAY BE USED IN THIS MANUAL
ABBREVIATIONS

GENERAL INFORMATION 0A-23
L
LH : Left Hand
LSPV : Load Sensing Proportioning
Valve
M
MAF Sensor : Mass Air Flow Sensor (Air Flow
Sensor, AFS, Air Flow Meter,
AFM)
MAP Sensor : Manifold Absolute Pressure
Sensor (Pressure Sensor, PS)
Max : Maximum
MFI : Multiport Fuel Injection
(Multipoint Fuel Injection)
Min : Minimum
MIL : Malfunction Indicator Lamp
M / T : Manual Transmission
N
NOx : Nitrogen Oxides
O
OBD : On-Board Diagnostic System
(Self-Diagnosis Function)
O / D : Overdrive
OHC : Over Head Camshaft
P
PNP : Park / Neutral Position
P / S : Power Steering
PSP Switch : Power Steering Pressure Switch
(P / S Pressure Switch)
PCM : Powertrain Control Module
PCV : Positive Crankcase Ventilation
R
RH : Right Hand
S
SAE : Society of Automotive
Engineers
SDM : Sensing and Diagnostic Module
(Air Bag Controller, Air Bag
Control Module)
SFI : Sequential Multiport Fuel
Injection
SOHC : Single Over Head Camshaft
T
TBI : Throttle Body Fuel Injection
(Single-Point Fuel Injection,
SPI)
TCC : Torque Converter Clutch
TCM : Transmission Control Module
(A / T Controller, A / T Control
Module)
TP Sensor : Throttle Position Sensor
TVV : Thermal Vacuum Valve
(Thermal Vacuum Switching
Valve, TVSV, Bimetal Vacuum
Switching Valve, BVSV)
TWC : Three-Way Catalytic Converter
(Three-Way Catalyst)
2WD : 2 Wheel Drive
V
VIN : Vehicle Identification Number
VSS : Vehicle Speed Sensor
W
WU-OC : Warm Up Oxidation Catalytic
Converter
WU-TWC : Warm Up Three-Way Catalytic
Converter

0B-2 MAINTENANCE AND LUBRICATION
MAINTENANCE SCHEDULE
NORMAL CONDITION SCHEDULE
Interval:
This interval should be
judged by
This table includes services as scheduled up to 90,000 km (54,000 miles)
mileage. Beyond 90,000 km (54,000 miles), carry out the same services at
the same intervals respectively.
jg y
odometer reading or months,Km(
1,000)153045607590
whichever comes first.Miles(
1,000)91827364554
Months122436486072
1. ENGINE
1-1.Drive belt (tension,V-beltIRIRIR
damage)
V-rib belt (Flat type)––I––R
1-2.Camshaft timing beltReplace every 100,000 km (60,000 miles).
1-3.Valve lash (1.3 liter engine)–I–I–I
1-4.Engine oilVehicle with O2S (SG, SH, SJ)RRRRRR
and oil filter
Vehicle with O2S (SE, SF)
Vehicle without O2SReplace every 10,000 km (6,000 miles)
or 8 months
1-5.Engine coolant–R–R–R
1-6.Exhaust system (leakage, damage, tightness)–I–I–I
2. IGNITION SYSTEM
2-1.Spark plugsWhen unleaded
fuel is usedVehicle
without
O2S
–R–R–R
Vehicle
with O2S––R––R
When leaded fuel is usedRefer to “Severe Driving Condition” schedule.
2-2.Distributor cap and rotor (if equipped)––I––I
3. FUEL SYSTEM
3-1.Air cleaner filterPaved-roadIIRIIR
Dusty conditionRefer to “Severe Driving Condition” schedule.
3-2.Fuel lines (deterioration, leakage, damage)–I–I–I
3-3.Fuel tank––I––I
NOTES:

For Item 2-1 “spark plugs”, replace every 50,000 km if the local law requires.

For Sweden, Item 2-1, 4-1 and 4-2 should be performed by odometer reading only.

For Item 1-2 Camshaft timing belt: This belt may be replaced every 90,000 km (54,000 miles) according
to customer’s maintenance convenience.

1. Thickness gauge IN
EX
0B-6 MAINTENANCE AND LUBRICATION
Water Pump Belt Replacement
Replace belt with a new one. Refer to SECTION 6B for replacement
procedure of pump belt.
NOTE:
When replacing belt with a new one, adjust belt tension to
5 – 7 mm (0.20 – 0.27 in.).
ITEM 1-2
Camshaft Timing Belt Replacement
Replace belt with new one. Refer to SECTION 6A or 6A1 for re-
placement procedure.
CAUTION:

Do not bend or twist timing belt.

Do not allow timing belt to come into contact with oil, wa-
ter, etc.
ITEM 1-3
Valve Lash Inspection (1.3 liter engine only)
1) Remove cylinder head cover.
2) Inspect intake and exhaust valve lash and adjust as necessary.
Refer to SECTION 6A1 for valve lash inspection and adjustment
procedure.
Valve
lash
(gap)
When cold
(Coolant temperature is
15 – 25C or 59 – 77F)When hot
(Coolant temperature is
60 – 68C or
140 – 154F)
(gap)
specifi-
cation
Intake0.13 – 0.17 mm
(0.005 – 0.007 in.)0.17 – 0.21 mm
(0.007 – 0.008 in.)
cation
Exhaust0.23 – 0.27 mm
(0.009 – 0.011 in.)0.28 – 0.32 mm
(0.011 – 0.013 in.)
Special Tool
(A): 09917-18211
Tightening Torque
(a): 12 N
.m (1.2 kg-m, 8.5 lb-ft)
3) Install cylinder head cover and tighten bolts to specification.

“a”: Parking brake lever stroke:
4 – 9 notches (With 20 kg
or 44 lbs of pull pressure)
1. Wear indicator1. Clutch pedal
“a”: Free travel
0B-14 MAINTENANCE AND LUBRICATION
ITEM 5-4
Brake Lever and Cable Inspection
Parking brake lever

Check tooth tip of each notch for damage or wear. If any damage
or wear is found, replace parking lever.

Check parking brake lever for proper operation and stroke, and
adjust it if necessary.
For checking and adjusting procedures, refer to PARKING
BRAKE INSPECTION AND ADJUSTMENT of SECTION 5.
Parking brake cable
Inspect brake cable for damage and smooth movement.
Replace cable if it is in deteriorated condition.
CHASSIS AND BODY
ITEM 6-1
Clutch Pedal Free Travel Inspection
Check clutch pedal free travel. Refer to SECTION 7C for procedure
to check and adjust it.
ITEM 6-2
Tire and Wheel Disc Inspection
[Tire inspection]
1) Check tire for uneven or excessive wear, or damage. If defec-
tive, replace.
2) Check inflating pressure of each tire and adjust pressure to
specification as necessary.
NOTE:

Tire inflation pressure should be checked when tires are
cool.

Specified tire inflation pressure should be found on tire
placard or in owner’s manual which came with vehicle.

6
ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-1
GENERAL INFORMATION6- 3 . . . . . . . . . . . . . .
Statement on Cleanliness and Care 6- 3. . . . .
General Information on Engine Service 6- 3. .
Precaution on Fuel System Service 6- 4. . . . .
Fuel Pressure Relief Procedure 6- 5. . . . . . . .
Fuel Leakage Check Procedure 6- 5. . . . . . . .
ENGINE DIAGNOSIS6- 6 . . . . . . . . . . . . . . . . . . . General Description 6- 6. . . . . . . . . . . . . . . . . . .
On-Board Diagnostic System 6- 6. . . . . . . . . .
Precaution in Diagnosing Trouble 6- 9. . . . . . .
Engine Diagnostic Flow Table 6-10. . . . . . . . . .
Customer Problem Inspection From 6-12. . . . .
Malfunction Indicator Lamp Check 6-13. . . . . .
Diagnostic Trouble Code Check 6-13. . . . . . . .
SECTION 6
ENGINE GENERAL INFORMATION
AND DIAGNOSIS
(TBI FOR G10)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI for G10)6-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI for G13)6-1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE MECHANICAL (G10)6A-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE MECHANICAL (G13 1 cam 16 valves)6A1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE COOLING6B-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE FUEL6C-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE AND EMISSION CONTROL SYSTEM (TBI for G10)6E1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE AND EMISSION CONTROL SYSTEM (SFI for G13)6E2-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IGNITION SYSTEM (G10 ENGINE)6F-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IGNITION SYSTEM (G13 ENGINE)6F1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CRANKING SYSTEM6G-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHARGING SYSTEM6H-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EXHAUST SYSTEM6K-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTE:
For the descriptions for vehicle without warm up three way catalytic converter (WUTWC), refer to Section
6 and 6E1 of the Service Manual mentioned in the FOREWORD of this manual.
CONTENTS

6-16 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
DTC
NO.DETECTING ITEMDETECTING CONDITION
(DTC will set when detecting:)MIL
P0335Crankshaft position sensor
circuit malfunctionNo signal during engine running1 driving cycle
P0340Camshaft position sensor
circuit malfunctionNo signal for 2 sec. during engine cranking1 driving cycle
P0420Catalyst system efficiency
below threshold
Output waveforms of HO2S-1 and HO2S-2
are similar.
(Time from output voltage change of HO2S-1
to that of HO2S-2 is shorter than
specification.)
2 driving cycles
P0443EVAP Purge control valve
circuit malfunctionPurge control valve circuit is open or shorted
to ground2 driving cycles
P0480Radiator fan control circuit
malfunctionRadiator cooling fan relay terminal voltage is
low when cooling temp. is lower than
specification
2 driving cycles
P0500Vehicle speed sensor
malfunctionNo signal while running in “D” range or during
fuel cut at decelerating2 driving cycles
P0505Idle control system malfunction
Throttle opening change is small as compared
with electrically live time. Throttle valve opening
is not within its target range with CTP switch ON
or drive voltage exists though ECM (PCM) is not
outputting ISC drive command.
1 driving cycle
P0510Closed throttle position switch
malfunctionSwitch does not change from ON to OFF
(or from OFF to ON) even when vehicle speed
reaches over (or below) specification.
2 driving cycle
P1250Early Fuel Evaporation Heater
Circuit MalfunctionHeater monitor terminal voltage is higher than
specified value when EFE OFF or it is lower
than specified value when EFE ON.
2 driving cycles
P1450Barometric pressure sensor
circuit malfunctionBarometric pressure is lower or higher than
specification. (or sensor malfunction)1 driving cycle
P1451Barometric pressure sensor
performance problem
Difference between manifold absolute
pressure (MAP sensor value) and
barometric pressure (barometric pressure
sensor value) is larger than specification
during cranking.
2 driving cycles
P1500Starter signal circuit
malfunctionStarter signal is not inputted from engine
cranking till its start and after or it is always
inputted
2 driving cycles
P1510ECM (PCM) backup power
source malfunctionNo backup power after starting engine1 driving cycle