2000 SUZUKI SWIFT engine oil

1. Clamp
1. Long bolt
2. Short bolt
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-23
6) To take up slack of timing belt, turn crankshaft two rotations
clockwise after installing it. After making sure that belt is free
from slack, tighten tensioner stud first and then tensioner bolt
to each specified torque.
Then confirm again that two sets of marks are aligned respec-
tively.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
(b): 25 N
.m (2.5 kg-m, 18.0 lb-ft)
7) Install timing belt outside cover.
Before installing, make sure that seal is between water pump
and oil pump case.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
8) With crankshaft locked, remove crankshaft timing belt pulley
bolt (4).
9) Install crankshaft pulley (2).
Fit hole of pulley to pin (1) on crankshaft timing belt pulley, and
tighten pulley bolts (3) to specified torque.
Tightening Torque
(a): 16 N
.m (1.6 kg-m, 11.5 lb-ft)
10) With crankshaft locked using flat end rod or the like, tighten
crankshaft timing belt pulley bolt (4).
Tightening Torque
(b): 130 N
.m (13.0 kg-m, 94.0 lb-ft)
11) Clamp harness securely.

1. Oil pan:
Apply sealant 99000-31150 to
oil pan mating surface.
2. Oil pump strainer
3. Seal
4. Drain plug gasket
5. Drain plug
6. CKP sensor : Tightening Torque
: Do not reuse
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-25
OIL PAN AND OIL PUMP STRAINER
REMOVAL
1) Raise vehicle.
2) Drain engine oil by removing drain plug (1).
3) Remove right side of engine under cover.
4) Disconnect CKP sensor coupler and remove CKP sensor (1) by
removing its bolt. Then remove CKP sensor wire harness from
clamp.
5) Remove clutch housing (torque converter housing for A / T) low-
er plate.

2. O-ring
6A1-26 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
6) Remove oil pan (3) and then oil pump strainer (1).
CLEANING

Clean mating surfaces of oil pan and cylinder block.
Remove oil, old sealant, and dusts from mating surfaces and oil
pan inside.

Clean oil pump strainer screen.
INSTALLATION
1) Apply sealant to oil pan mating surface continuously as shown
in figure.
“A” Sealant: 99000-31150
Sealant amount
Width “a”: 4 mm, 0.16 in.
Height “b”: 2 mm, 0.08 in.
2) Install O-ring (2) into cylinder block securely as shown in figure.
Install oil pump strainer (1) to cylinder block.
Tighten strainer bolt first and then bracket bolt to specified
torque.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
After fitting oil pan (3) to cylinder block, run in securing bolts and
start tightening at the center: move wrench outward, tightening
one bolt at a time.
Tighten bolts to specified torque.
Tightening Torque
(b): 11 N
.m (1.1 kg-m, 8.0 lb-ft)

ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-27
3) Install new gasket and drain plug to oil pan.
Tighten drain plug to specified torque.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36 lb-ft)
4) Install clutch (torque converter) housing lower plate.
5) Install CKP sensor (1) and connect its coupler, then clamp its
harness.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
6) Install right side of engine under cover.
7) Refill engine with engine oil referring to “ENGINE OIL CHANGE”
in Section 0B.

1. Rotor plate
2. Inner rotor:
Apply thin coat of engine oil.
3. Outer rotor:
Apply thin coat of engine oil.
4. Gasket
5. Pin
6. Pin
7. Relief valve:
Apply thin coat of engine oil.
8. Spring
9. Retainer
10. Retainer ring
11. Front oil seal:
Apply engine oil to contact
part of crankshaft with oil seal lip.
12. Plate screw
13. Bolt (short)
14. Bolt (long)
: Tightening Torque
: Do not reuse
6A1-28 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
OIL PUMP
REMOVAL
1) Disconnect negative cable at battery.
2) Remove timing belt as previously outlined.
3) Remove generator and its bracket.
NOTE:
When installing bracket, fasten nut (A) first.
4) Remove power steering pump bracket or A / C compressor
bracket, if equipped.
NOTE:
When installing bracket, fasten bolt (B) first.
5) Remove oil pan and oil pump strainer as previously outlined.
6) Remove crankshaft timing belt pulley (3).
Lock crankshaft inserting flat end rod or the like (1) between fly-
wheel ring gear and transmission case.
With crankshaft locked, remove crankshaft timing belt pulley
bolt (2).

4. Guide seal
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-29
7) Remove oil pump assembly (1) after removing bolts (2).
DISASSEMBLY
1) Remove oil level gauge guide bolt (3) and pull out guide (2) from
oil pump (1).
2) Remove rotor plate (1).
3) Remove outer rotor (1) and inner rotor (2).
INSPECTION

Check oil seal lip for fault or other damage. Replace as necessary.

6A1-30 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
NOTE:
When installing oil seal (1), press-fit it till its end face is flush
with oil pump case (2) end face.

Check outer and inner rotors, rotor plate, and oil pump case for
excessive wear or damage.
MEASUREMENT

Radial clearance
Check radial clearance between outer rotor (1) and case, using
thickness gauge.
If clearance exceeds its limit, replace outer rotor or case.
Limit on radial clearance between outer rotor and case:
0.200 mm (0.079 in.)

Side clearance
Using straight edge and thickness gauge, measure side clear-
ance.
Limit on side clearance: 0.10 mm (0.0039 in.)
ASSEMBLY
1) Wash, clean and then dry all disassembled parts.
2) Apply thin coat of engine oil to inner (2) and outer rotors (1), oil
seal lip portion, and inside surfaces of oil pump case and plate.
3) Install outer and inner rotors to pump case.

(a)
1. Oil pump
1. No. 1 bolts (short)
2. No. 2 bolts (long)
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-31
4) Install rotor plate. Tighten 5 screw securely.
After installing plate, check to be sure that gears turn smoothly
by hand.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
5) Apply engine oil to guide seal (3) and install guide seal and guide
(2).
INSTALLATION
1) Install two oil pump pins and oil pump gasket to cylinder block.
Use a new gasket.
2) To prevent oil seal lip from being damaged or upturned when
installing oil pump to crankshaft, fit special tool (Oil seal guide)
to crankshaft, and apply engine oil to special tool.
Special Tool
(A): 09926-18210
3) Install oil pump to cylinder block.
As there are 2 types of oil pump bolts, refer to figure for their cor-
rect use and tighten them to specified torque.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
4) Install rubber seal between oil pump and water pump.