2000 MITSUBISHI MONTERO coolant

GDI -Troubleshooting 13A-199
Item
No.Reference
page Inspection
procedure
No. Normal condition Inspection contents Inspection
item
14Throttle
positionDEngine: After hav-
ing warmed upRelease the acceler-
ator pedal.4,000 mV or moreCode No.
1413A-137
sensor (2nd
channel)DIgnition switch: ON
(Engine: Stopped)
Depress the acceler-
ator pedal gradually.Voltage
decreases in
response to the
pedal depression.
Depress the acceler-
ator pedal fully.400 - 600 mV
16System
voltageIgnition switch: ONSystem voltageProcedure
No. 2513A-190
18Cranking
signal (igni-Ignition switch: ONEngine: StoppedOFFProcedure
No.2713A-191
signal (igni-
tion switch:
ST)
Engine: CrankingON
No.27
21Engine cool-
ant temper-
ature sensorIgnition switch: ON or
with engine runningWhen engine coolant
temperature is
-20_
C-20_
CCode No.
2113A-138
When engine coolant
temperature is 0_
C0_
C
When engine coolant
temperature is 20_
C20_
C
When engine coolant
temperature is 40_
C40_
C
22Crank angle
sensorDEngine: Cranking
DTachometer: Con-
nectedCompare the
tachometer with the
MUT-IIreading.IdenticalCode No.
2213A-140
DEngine: Idling
DIdle position
switch: ON
DWithin six minutesWhen engine coolant
temperature is
-20_
C1,250 - 1,450
r/min
DWithin six minutes
after engine
starting (Onlywhen
engine coolant
When engine coolant
temperature is 0_
C1,100 - 1,300
r/min
engine coolant
temperature is
80
_C)
When engine coolant
temperature is 20_
C1,000 - 1,200
r/min
When engine coolant
temperature is 40_
C900 - 1,100 r/min
When engine coolant
temperature is 80_
C550 - 650 r/min


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-200
Item
No.Reference
page Inspection
procedure
No. Normal condition Inspection contents Inspection
item
25BarometricIgnition switch: ONAt altitude of 0 m101 kPaCode No.13A-145
pressure
sensor
At altitude of 600 m95 kPa
25
At altitude of 1,200 m88 kPa
At altitude of 1,800 m81 kPa
26Accelerator
pedal posi-Ignition switch: ON
(Depress and re-Release the acceler-
ator pedal.ONProcedure
No.2813A-192
tion switchlease the accelerator
pedal several times)
Depress the acceler-
ator pedal slightly.OFF
27Power
steering
fluid pres-
sure switchEngine: IdlingWhen steering wheel
is turnedONProcedure
No.3013A-194
28A/C switchEngine: Idling
(The A/C compres-A/C switch: OFFOFFProcedure
No.3113A-194
(The A/C compres-
sor is running when
the A/C switch is on.)
A/C switch: ONON
No.31
31Small lampEngine: IdlingLighting switch: OFFOFFProcedure13A-195
switch
Lighting switch: ONON
No.33
34Air flow sen-Engine: After havingIdlingONCode No.13A-133
sor reset
signalwarmed up
3,000 r/minOFF
12
37VolumetricDEngine coolantIdling20 - 40%--
efficiencytemperature: 85 -
95
_C
Lamps and all
2,500 r/min10 - 30%DLamps and all
accessories: OFF
DTransmission: P
range
Engine is suddenly
racedVolumetric effi-
ciency increases
in response to
racing
38Crank angle
sensorDEngine: Cranking (reading is possible at 2,000
r/min or less)
DTachometer: ConnectedEngine speeds
displayed on the
MUT-IIand
tachometer are
identical.--


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-201
Item
No.Reference
page Inspection
procedure
No. Normal condition Inspection contents Inspection
item
41Injector
drive time*1D
Engine: CrankingWhen engine coolant
temperature is 0_
C120 - 160 msCode No.
4113A-147
When engine coolant
temperature is 20_
C70 - 90 ms
When engine coolant
temperature is 80_
C20 - 35 ms
Injector
drive time*2D
Engine coolant
temperature: 85 -
95_
CIdling0.3 - 0.8 ms
95_
C
D
Lamps and all
accessories: OFF
D
Transmission:
2,500 r/min0.4 - 1.0 ms
D
Transmission:
P range
D
Within six minutes
after engine start-
ing
When engine is sud-
denly racedIncreases
44Ignition ad-
vance valueD
Engine: After hav-
ing warmed up
D
Timing lamp is set.
(The timing lamp is
set in order toIdling12 - 28_
BTDCCode No.
4413A-148
set in order to
check actual igni-
tion timing.)
D
Within six minutes
after engine start-
ing
2,500 r/min15 - 35_
BTDC
49A/C relayEngine: After having
warmed up, idlingA/C switch: OFFOFF (compressor
clutch is not oper-
ating)Procedure
No.3113A-194
A/C switch: ONON (compressor
clutch is operat-
ing)
67Stop lamp
switchIgnition switch: ONBrake pedal: De-
pressedOFFProcedure
No.3213A-195
Brake pedal: Re-
leasedON
68EGR valveD
Engine coolant
temperature: 85 -
95_
CIdling2 - 20 STEPProcedure
No.3513A-196
D
Lamps and all
accessories: OFF
D
Transmission: P
range
2,500 r/min0 - 10 STEP
74Fuel pres-
sure sensorD
Engine coolant
temperature: 85 -
95_
CEngine: Cranking2 MPa or moreCode No.
5613A-151
D
Lamps and all
accessories: OFF
D
Transmission: P
range
Engine: Idling4.0 - 6.9 MPa


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-205
Terminal
No.Normal condition Check condition (Engine condition) Check item
18Condenser fan relayCondenser fan not operatingSystem voltage
Condenser fan operating0 - 3 V or more
19Air flow sensor resetEngine: Idling0-1V
signal
Engine speed: 3,000 r/min6-9V
20A/C relayDEngine: Idling
DA/C switch: OFF to ON (Compressor operating)System voltage or
changes momentarily 6
V or more to 0 - 3 V
21Fuel pump relayIgnition switch: ONSystem voltage
Engine: Idling0-3V
22Engine warning lampIgnition switch: OFF to ONSystem voltage
23GDI ECO indication
lampIgnition switch: OFF to ON0 - 3 V (system voltage
after five seconds)
Rev the engine suddenly.System voltage
34Purge control solenoidDEngine coolantEngine: stoppedSystem voltage
valvetemperature: 80 -
95_C
DIgnition switch:
ON
Engine: After starting, in-
crease the engine speed
up to 3,500 r/minThe voltage drops
41Power supplyIgnition switch: ONSystem voltage
47
43Engine ignition signalEngine speed: 3,000 r/min0.3 - 3.0 V
44Engine coolant tem-
perature sensorIgnition switch: ONWhen engine coolant tem-
perature is 0_C3.2 - 3.8 V
When engine coolant tem-
perature is 20_C2.3 - 2.9 V
When engine coolant tem-
perature is 40_C1.3 - 1.9 V
When engine coolant tem-
perature is 80_C0.3 - 0.9 V
45Crank angle sensorEngine: Cranking0.4 - 4.0 V
Engine: Idling1.5 - 2.5 V
46Power supply voltage
applied to accelerator
pedal position sensor
(1st channel)Ignition switch: ON4.5 - 5.5 V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting13A-5
DATA LIST REFERENCE TABLE
The data list has been changed as the engine-ECU and the engine-A/T-ECU have been changed. The
other items are the same as for M/T.
Item
No.Inspection
itemInspection contentsNormal conditionInspec-
tion pro-
cedure
No.Refer-
ence
page
22Crank angle
sensorDEngine: Cranking
DTachometer:
ConnectedCompare the engine
speed readings on
the tachometer and
the MUT-II.AccordCode
No.
P033513A-56*
DEngine: Idling
DIdle position
switch: ONWhen engine
coolant temperature
is - 20_C1,300 - 1,500
r/min
When engine
coolant temperature
is 0_C1,300 - 1,500
r/min
When engine
coolant temperature
is 20_C1,250 - 1,450
r/min
When engine
coolant temperature
is 40_C1,100 - 1,300
r/min
When engine
coolant temperature
is 80_C (more than
four minutes later
after engine has
started)600 - 800 r/min
A1LOxygen
sensorEngine: After having
warmed up. (Air/fuel
mixture is made
leaner when deceler-When at 4,000
r/min, engine is
decelerated200 mV or lessCode
No.
P013013A-28*
leanerwhendeceler
ating, and is made
richer when racing.)Rev the engine.600 - 1000 mV
Engine: After having
warmed up (The
oxygen sensor signal
is used to check the
air/fuel mixture ratio,
and control condition
isalsocheckbythe
Engine is idling
(more than 4
minutes later after
engine has started)Voltage should
alternate between
400 mV or less
and 600 - 1,200
mV (more than 4
minutes after the
enginehasisalso checkbythe
engine-ECU
or engine-A/T-ECU
.)
2,500 r/min
enginehas
started).
24LVehicle
speed sen-
sorDrive at 40 km/hApproximately 40
km/hCode
No.
P050013A-63*


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

13C-1
DIESEL FUEL
<4M4>
CONTENTS
GENERAL INFORMATION 2...................
SERVICE SPECIFICATIONS 3.................
SEALANT 3..................................
SPECIAL TOOLS 4...........................
TROUBLESHOOTING 5.......................
ON-VEHICLE SERVICE 42...................
Injection Timing Check and Adjustment 42.........
Idle Speed Check and Adjustment 42.............
Accelerator Pedal Position Sensor (APS)
Adjustment 42.................................
Control Relay Continuity Check 43................
Accelerator Pedal Position Sensor (APS) Check 43.Idle Switch Check 43...........................
Boost Air Temperature Sensor (Intake Air
Temperature Sensor) Check 44..................
Engine Coolant Temperature Sensor Check 44.....
Evacuation of Water from Fuel Filter 45...........
Fuel Filter Cartridge Replacement 45.............
Evacuation of Air from Fuel Line 45...............
Fuel Injection Pump Check 46...................
Intake Air Restriction Equipment Check 48.........
Injection Nozzle Check and Adjustment 49.........
INJECTION NOZZLE 50......................
INJECTION PUMP 56........................
ENGINE-ECU 59............................


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

DIESEL FUEL <4M4> -General Information13C-2
GENERAL INFORMATION
The electronically-controlled fuel injection system consists of sensors which detect the condition of the
diesel engine, an engine-ECU which controls the system based on signals from these sensors, and actuators
which operate according to control commands from the engine-ECU.
The engine-ECU carries out operations such as fuel injection rate control, fuel injection timing control
and idle up control. In addition, the engine-ECU is equipped with several self-diagnosis functions which
make troubleshooting easier in the event that a problem develops.
FUEL INJECTION RATE CONTROL
The fuel injection completion timing is controlled by means of a solenoid-type spill valve to ensure that
the optimum amount of fuel is supplied to the engine in accordance with gradual changes in the engine
running condition.
Before fuel injection starts, the solenoid-type spill valve is on (energized), so that the valve is closed.
As the plunger turns and rises, fuel is sent out under pressure, and when the fuel flow rate reaches
the target value for fuel injection, the solenoid-type spill valve turns off. When the solenoid-type spill
valve turns off, the fuel under high pressure inside the plunger is leaked out into the pump chamber
and fuel injection is completed.
FUEL INJECTION TIMING CONTROL
The position of the injection pump timer piston is controlled so that fuel injection is carried out at the
optimum timing in accordance with the engine running condition.
The timer piston position is determined by duty control of the timing control solenoid valve which is located
in the line between the high-pressure chamber and the low-pressure chamber of the timer piston.
The fuel injection timing is advanced by increasing the control duty of the timing control solenoid valve.
IDLE SPEED CONTROL
Controlling the fuel injection rate in accordance with the engine running condition maintains the idle speed
at the optimum condition.
SELF-DIAGNOSIS FUNCTION
DWhen an abnormality is detected in any of the sensors or actuators, the engine warning lamp illuminates
to warn the driver.
DWhen an abnormality is detected in any of the sensors or actuators, a diagnosis code number
corresponding to the problem which occurred is output.
DThe RAM data relating to the sensors and actuators which is stored in the engine-ECU can be read
using the MUT-II. In addition, the actuators can be force-driven under certain conditions.
OTHER CONTROL FUNCTIONS
1. Power Supply Control
When the ignition switch is turned to ON, the relay turns on and power is supplied to components
such as the timing control solenoid valve.
2. Intake Air Throttle Control
When the engine is idling after having warmed up, the throttle valve is half opened to restrict the
amount of intake air in order to reduce vibration and noise.
3. A/C Relay Control
Turns the compressor clutch of the A/C ON and OFF
4. Fan motor relay control
The radiator fan and condenser fan operating speeds are controlled in accordance with the engine
coolant temperature and the vehicle speed.
5. Glow Control
Refer to GROUP 16.
6. EGR Control
Refer to GROUP 17.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

DIESEL FUEL <4M4> -Service Specifications/Sealant13C-3
SERVICE SPECIFICATIONS
ItemStandard value
Accelerator pedal position sensor reference voltage V0.985 - 1.085
Accelerator pedal position sensor resistance kW3.5 - 6.5
Boost air temperature sensor (Intake air temperatureWhen the temperature is 20_C2.3 - 2.9
sensor) resistance kWWhen the temperature is 80_C0.30 - 0.39
Engine coolant temperature sensor resistance kWWhen the temperature is 20_C2.3 - 2.6
When the temperature is 80_C0.30 - 0.34
Fuel cut solenoid valve resistanceW6.8 - 9.2
Timing control valve resistanceW10.8 - 11.2
Timer piston position sensor resistanceWConnector terminals No.1 - No.2160 - 168
Connector terminals No.1 - No.380 - 84
Connector terminals No.2 - No.380 - 84
Control sleeve position sensor resistanceWConnector terminals No.4 - No.1211.2 - 12.4
Connector terminals No.4 - No.85.6 - 6.2
Connector terminals No.8 - No.125.6 - 6.2
GE actuator (electronic governor) resistanceWConnector terminals No.6 - No.100.64 - 0.72
Fuel temperature sensor resistance kWConnector terminals No.7 - No.111.4 - 2.6
Engine speed sensor resistance kW2.15
Main/sub throttle solenoid valve resistanceW36 - 44
SEALANT
ItemSpecified sealant
Engine coolant temperature sensor3M Nut Locking Part No.4171 or equivalent


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk