2000 MITSUBISHI MONTERO battery

GDI -Troubleshooting 13A-103
Inspection procedure 32
Stop lamp switch system
Probable cause
The engine-ECU determines whether the brakepedal is depressed or not, by means
of the stoplampswitch input signal.DMalfunction of the stoplampswitch
DOpen circuit or short-circuited harness wire in the stop
lampcircuit, or poor connector contact
DMalfunction of the engine-ECU
NG
NG
NG
Repair
Check the stoplampswitch. (Refer to GROUP 35 - Brake Pedal.)NG
Replace
OK
Measure at stoplampswitch connector D-136.
DDisconnect the connector, and measure at the harness side.
DVoltage between terminal 2 and earth
OK:
System voltageNG
OK
Check trouble symptom.
Check the harness wire between the battery and stoplampswitch.
NG
Repair
OK
Measure at engine-ECU connector D-117.
DDisconnect the connector, and measure at the harness side.
DVoltage between terminal 63 and earth
(Ignition switch: ON)
OK:
0 - 3 V (when the brakepedal is not depressed)
System voltage (when the brakepedal is depressed)NG
OK
Check trouble symptom.
Check the harness wire between the engine-ECU and stoplamp,
and repair if necessary.
OK
Check the following connector:
D-117NG
Repair
OK
Check trouble symptom.
NG
Replace the engine-ECU.
Check the following connectors:
D-26 , D-27, D-124

Check the following connectors:
D-26 , D-124 ,
D-128, E-13


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-145
Code No.25 Barometric pressure sensor systemProbable cause
Range of Check
DTwo seconds have passed since the ignition switch is turned ON or the
engine startingprocess is completed.
DBattery voltage: 8 V or more
Set Conditions
DThe sensor output voltage is 4.5 V or more for four seconds (equivalent to
114 kPa of barometric pressure)
or
DThe sensor output voltage is 0.2 V or less (equivalent to 53 kPa of
barometric pressure)DMalfunction of barometric pressure sensor
DOpen or short circuit in barometric pressure
sensor circuit or loose connector contact
DMalfunction of engine-A/T-ECU
(2) NGCheck the following connector:
D-121NG
Repair
OK
Check the harness between the air
flow sensor and the engine-A/T-ECU,
and repair if necessary.
MUT-
IIData list
25 Barometric pressure sensor
(Refer to P.13A-198, DATA LIST
REFERENCE TABLE.)OKTransient malfunction
(Refer to GROUP 00 - Points to
Note for Intermittent Malfunctions.)
NG
NG
Repair
OK
Measure at air flow sensor connector
B-120.
DDisconnect the connector and
measure at the harness side.
(1) Voltage between terminal 1 and
earth (Ignition switch: ON)
OK:
4.8 - 5.2 V
(2) Resistance between terminal 5
and earth
OK:
2Wor less(1) NGMeasure at engine-A/T-ECU
connector D-121.
DMeasure the voltage at the
engine-A/T-ECU terminal.
DIgnition switch: ON
DVoltage between terminal 87 and
earth
OK:
4.8 - 5.2 VOKCheck the following connector:
D-121
NG
Repair
NG
Check the following connector:
D-121NG
Repair
OK
Check the harness between the air
flow sensor and the engine-A/T-ECU.NG
Repair
OK
Check the trouble symptoms.NGReplace the engine-A/T-ECU.
OK
Measure at air flow sensor connector
B-120.
DConnect connector terminals
No.1, No.2 and No.5 only by
using test harness (MB991709),
and measure at the pick - up
harness.
DIgnition switch: ON
(1) Voltage between terminal 1 and
earth
OK:
4.8 - 5.2 V
(2) Voltage between terminal 2 and
earth
OK:
Altitude 0 m: 3.7 - 4.3 V
Altitude 1200 m:
3.2 - 3.8 V
(3) Voltage between terminal 5 and
earth
OK:
0.5 V or less(1) NGCheck the following connector:
D-121NG
Repair
OK
Check the harness between the air
flow sensor and the engine-A/T-ECU,
and repair if necessary.
OK
To the nextpage(3) NG
(2) NG
Replace the air flow sensor.
NG
Check the following connector:
D-120NG
Repair
OK
Check the harness between the air
flow sensor and the engine-A/T-ECU,
and repair if necessary.
OK
Check the harness between the air
flow sensor and the engine-A/T-ECU.NG
Repair
OK
Check the trouble symptoms.NGReplace the engine-A/T-ECU.
Check the following connector:
B-120
Check the trouble symptoms.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-147
Code No.41 Injector systemProbable cause
Range of Check
DThe enginespeed is 4,000 r/min or less.
DThe battery voltage is 10 V or more.
DThe fuel cut operation or the injector operation (by carrying out the Actuator
Test) is not in progress.
Set Conditions
DThe injector driver is not transmitting a injectoropencircuit check signal for
four seconds.DMalfunction of injector
DOpen or short circuit in the injector circuit or loose
connector contact
DMalfunction of engine-A/T-ECU
NG
Check the following connector:
B-105NG
Repair
OK
NG
Repair
MUT-
IIActuator Test
01 No.1 injector
02 No.2 injector
03 No.3 injector
04 No.4 injector
05 No.5 injector
06 No.6 injector
OK:
The idling condition should
change.OKCheck the trouble symptoms.OKTransient malfunction
(Refer to GROUP 00 - Points to
Note for Intermittent Malfunctions.)
NG
Replace the injector driver.
Check the trouble symptoms.NGReplace the engine-A/T-ECU.
OK
Measure at intermediate connector
B-105.
DDisconnect the connector and
measure at the harness side.
DResistance between terminals 11
and 12
Resistance between terminals 5
and 6
Resistance between terminals 9
and 10
Resistance between terminals 3
and 4
Resistance between terminals 7
and 8
Resistance between terminals 1
and 2
OK:
0.9 - 1.1WNGCheck the following connectors:
B-117 , B-114 injector>, B-118 ,
B-115 , B-103 injector>, B-104 NG
Repair
OK
Replace the injector.
Check the following connector:
B-121NG
Repair
OK
Check the harness wire between the
injector driver and the intermediate
connector.NG
Repair
OK
Check the following connector:
D-119NG
Repair
OK
Check the harness wire between the
injector driver and the
engine-A/T-ECU.NG
Repair
OK
To the nextpage
Check the harness wire between
injector and the intermediate
connector.
OK


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-162
Code No.92 Throttle valve position feedback systemProbable cause
The throttle valve controller judges a malfunction, and then transmit the result to
the engine-A/T-ECU.
Range of Check
DIgnition switch: ON
DBattery voltage: 10 V or more
Set Conditions
DFailure in the position feedback
[The engine-A/T-ECU detects that the current in the motor isexcessive and
the opening angle difference between the targetvalue of throttle position
sensor (1st channel) and the actual value of throttle position sensor (1st
channel) is 2.0V or more]DMalfunction of throttle position sensor (1st channel)
DOpen or short circuit in the throttle position sensor
(1st channel) circuit or loose connector contact
DMalfunction of the throttle valve controller
NG
Replace the throttle valve controller.
OK
Check the trouble symptoms.
NG
Check the harness wires between the throttle position sensor
and the throttle valve controller, and between the throttle valve
control servo and the throttle valve controller.NG
Repair
NO
Adjust the throttle position sensor. (Refer to P.13A-220.)
MUT-
IISelf-Diag Code
Is code No.79 set?YESRefer to Code No.79, Throttle position sensor (1st channel)
system. (Refer to P.13A-158.)
NO
MUT-
IISelf-Diag Code
Is Code No.93 set?YESRefer to Code No.93, Throttle valve control servo system
(Refer to P.13A-163.)
OK
Check the following connectors:
B-102, B-122, D-11NG
Repair
OK
Check the throttle valve control servo. (Refer to 13A-232.)NGReplace the throttle body assembly.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-164
Code No.94 Communication line system with the throttle
valve controllerProbable cause
Range of Check
DIgnition switch: ON
DBattery voltage: 8 V or more.
DEngine: not cranking
Set Conditions
DSystem detects an error in communicationline between the engine-A/T-ECU
and the throttle valve controller, and between the throttle valve controller and
the engine-A/T-ECU.DShort in communicationline
DMalfunction of engine-A/T-ECU
DMalfunction of throttle valve controller
MUT-
IISelf-Diag Code
Is Code No.91 output?YESRefer to Code No.91, Electronic-con-
trolled throttle valve system (Refer to
P13A-161.)
NO
NG
Repair
OK
Measure at throttle valve controller
connector D-11.
DMeasure voltage at the throttle
valve controller connector
terminals.
DIgnition switch: ON
(1) The voltage between terminal 5
and earth
OK:
System voltage
(2) The voltage between terminal 22
and earth
OK:
System voltage
(3) The voltage between terminal 3
and earth
The voltage between terminal 4
and earth
The voltage between terminal 16
and earth
OK:
0.5 V or less(1) NGCheck the following connectors:
B-25X,
D-128NG
Repair
Check the trouble symptoms.OK
Check the harness wire between the
throttle valve controller and theengine
control relay, and repair if necessary.
OK
Check the trouble symptoms.
NG
Replace the engine-A/T-ECU.
(2) NGCheck the following connectors:
D-208,
D-223, E-13NG
Repair
OK
Check the harness wire between the
throttle valve controller and the ignition
switch, and repair if necessary.
(3) NGCheck the following connector:
D-14NG
Repair
OK
Check the harness wire between the
throttle valve controller and earth, and
repair if necessary.
OK
Check the following connectors:
D-119, D-122NG
Repair
OK
Check the harness wire between the
throttle valve controller and the
engine-A/T-ECU.NG
Repair
NG
Replace the throttle valve controller.
Check the following connector:
D-11


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-169
INSPECTION PROCEDURE FOR TROUBLE SYMPTOMS
Inspection procedure 1
Communication with all systems is not possible.
Probable cause
The cause is probably a defect in the power supply system (including earth) for
the diagnosis line.DMalfunction of the diagnosis connector
DOpen circuit or short-circuited between
engine-A/T-ECU and diagnosis connector circuit
DMalfunction of the MUT-II
Check the earth line, and repair if
necessary.
(2) NG
Replace the MUT-II.
NG
Check the harness wire between the
power supply and diagnosis
connector, and repair if necessary.
OK
Check the trouble symptoms.NG
Repair
(1) NGCheck the following connectors:
D-27, D-210, D-211
OK
NG
RepairOK
Check the harness wire between
diagnosis connector and the
engine-A/T-ECU.
Measure at the diagnosis connecter
D-23.
(1) The voltage between terminal 16
and earth
OK:
Battery voltage
(2) Continuity between 4 and earth
Continuity between 5 and earth
OK:
Continuity
Inspection procedure 2
Communication with engine-A/T-ECU is not possible.
Probable cause
The cause is probably a defect in the engine-A/T-ECU power supply circuit
(including earth).DOpen circuit or short-circuited harness wire in the
engine-A/T-ECU power supply circuit.
DOpen circuit between engine-A/T-ECU and
diagnosis connector
DMalfunction of the engine-A/T-ECU
NG
Check the harness wire between engine-A/T-ECU and
diagnosis connector.OKCheck the engine-A/T-ECU power supply and earth circuit.
(Refer to P. 13A-189, Inspection procedure 24.)
OK
Check the trouble symptoms.
Check the following connectors:
D-06, D-23, D-122, D - 128,
D-222, E-13NG
Repair
NOTE
On vehicles with multi communication system (MMCS) or RV meter, if a malfunctioncannot be resolved
after the procedure above, check the multi center display unit or RV meter and replace if necessary.
(Refer to GROUP 54 - Clock, multi center display and RV meter.)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-170
Inspection procedure 3
The engine warning lamp does not illuminate right after
the ignition switch is turned to the ON position.
Probable cause
Because there is a burnt-out bulb, the engine-A/T-ECU causes theengine
warning lamp to illuminate forfive seconds immediately after the ignition switch
is turned to ON.
If the engine warning lampdoes notilluminate immediately after the ignition
switch is turned to ON, one of the malfunction listed at right has probably
occurred.DBurnt-out bulb
DOpen circuit or short-circuit between theengine
warning lamp and engine-A/T-ECU.
DMalfunction of the engine-A/T-ECU
NG
Replace the engine-A/T-ECU.
NG
Check the harness wire between
combination meter and
engine-A/T-ECU connector, and
repair if necessary.NG
Check theengine warning lamp
power supply circuit, and repair if
necessary.
OK
Check the trouble symptoms.
OK
Measure at the combination meter
connector D-01.
DDisconnect the connector, and
measure at the harness side.
DVoltage between 62 and earth
(Ignition switch: ON)
OK:
Battery voltageOKCheck the following connectors:
D-02, D-119, E-13NG
Repair
NG
Check a burnt-out bulb.NG
Replace
OK
Check the trouble symptoms.
OK
Measure at the engine-A/T-ECU
connector D-119.
DDisconnect the connector, and
measure at the harness side.
DEarth the terminal 22
(Ignition switch: ON)
OK:
Engine warning lamp illumi-
nates.OKCheck the following connector:
D-119NG
Repair
MUT-
IIData list
16 Engine-A/T-ECU power supply
voltage
(Refer to P.13A-198.)NGCheck the engine-A/T-ECU power
supply and earth circuit (Refer to
P.13A-189, Inspection procedure 24.)
Inspection procedure 4
The engine warning lamp remains illuminating and
never goes out.
Probable cause
In cases such as the above, the cause is probably that the engine-A/T-ECU is
detecting a problem in a sensor or actuator, or that one of the malfunctions
listed at right has occurred.DShort-circuit between the engine warning lamp and
engine-A/T-ECU
DMalfunction of the engine-A/T-ECU
Replace the engine-A/T-ECU.
NO
Measure at the combination connector D-02.
DDisconnect the connector, and measure at the harness
side.
DDisconnect the engine-A/T-ECU connector
DContinuity between 38 and earth
OK:
No continuityNGCheck the harness wire between combination meter and
engine-A/T-ECU connector, and repair if necessary.
OK
MUT-
IISelf-Diag Code
Is a diagnosis code set?YESRefer to P.13A-130, INSPECTION CHART FOR DIAGNOSIS
CODES.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-171
Inspection procedure 5
No initial combustion (starting impossible)
Probable cause
In cases such as the above, the cause is probably that a sparkplug is
defective, or that the supply of fuel to the combustion chamber is defective.
In addition, foreign materials (water, kerosene, etc.) may be mixed with the fuel.DMalfunction of the fuel supply system
DMalfunction of the ignition system
DMalfunction of the engine-A/T-ECU
NGRepair
OK
MUT-
IIData list
22 Crankanglesensor (Refer to P.13A-198.)NGCheck the crankanglesensor system.
(Refer to P.13A-140, code No.22.)
YES
MUT-
IIActuator Test
07 Fuel pump(low pressure) (Refer to P.13A-203.)NGCheck fuelpump(low pressure) system
(Refer to P.13A-193, Inspection procedure 29.)
OK
Does the camshaft rotate when theengine is cranking?NOCheck if thetiming belt isbroken ordamaged.
NO
MUT-
IIData list
16 Battery voltage (Refer to P.13A-198.)NGCheck theengine controlrelay and ignition switch-IG system
(Refer to P.13A-190, Inspection procedure 25.)
OK
MUT-
IISelf-Diag Code
Is a diagnosis code set?YESRefer to P.13A-130, INSPECTION CHART FOR DIAGNOSIS
CODES
Check battery voltage when cranking.
OK:
8 V or higherNGCheck the battery.
OK
Is starting good if the engine iscranked with the accelerator
pedalslightly depressed?YESDClean the throttle valve area. (Refer to P.13A-220.)
DCheck and adjust the throttle position sensor (Refer to
P.13A-220.)
OK
MUT-
IIData list
79 Throttle position sensor (1st channel) (Refer to P.13A-198.)NGCheck the throttle position sensor (1st channel) system
(Refer to P.13A-158, code No.79.)
OK
MUT-
IIData list
21 Engine coolant temperature sensor (Refer to P.13A-198.)NGCheck theengine coolant temperaturesensor system
(Refer to P.13A-138, code No.21.)
OK
Measure low fuel pressure between the fuelpump(low
pressure) and fuelpump (highpressure) (Refer to P.13A-222.)NGRepair
OK
To the nextpage
NO
Adjust the throttle position sensor (Refer to P.13A-220.)
NG
Measure at injector driver connector B-19
DDisconnect the connector, and measure at the harness
side.
DThe voltage between terminals 4, 12, 21 and earth
(Ignition switch: ON)
OK
Battery voltage
Check fuel leakage (Refer to P.13A-225.)OK
Check the injector driver system.
(Refer to P.13A-196, Inspection procedure 34.) NG


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk