2000 LEXUS GS400 torque

N20339
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY
RS±51
2282 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
9. INSTALL FRONT SEAT OUTER BELT FLOOR AN-
CHOR
(a) Install the front seat outer belt floor anchor.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
(b) Install the seat belt anchor cover cap.

RS07P±01
H02615
End Pad
Finish Panel
No.1 Safety Pad
Hood Lock
Release Lever
No.1 Under CoverFront Ash Receptacle
Cluster Finish PanelGlove Compartment
Finish Plate
Glove Compartment
Panel Assembly
No.2 Under Cover
Accessary Socket Case
Accessary Socket
Console Box Carpet
Rear Console
Armrest
Console Box Register No.3 Console Box
Mounting Bracket
Console Box
No.1 Console Box Duct
Airbag Sensor Assembly
: Specified torqueN´m (kgf´cm, ft´lbf)
20 (200, 14)
RS±52
± SUPPLEMENTAL RESTRAINT SYSTEMAIRBAG SENSOR ASSEMBLY
2283 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
AIRBAG SENSOR ASSEMBLY
COMPONENTS

RS07T±01
H02616
RS±56
± SUPPLEMENTAL RESTRAINT SYSTEMAIRBAG SENSOR ASSEMBLY
2287 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSTALLATION
NOTICE:

Never use SRS parts from another vehicle. When re-
placing parts, replace them with new parts.

Never reuse the airbag sensor assembly involved in
a collision when the airbag has deployed.

Never repair a sensor in order to reuse it.
1. INSTALL AIRBAG SENSOR ASSEMBLY
(a) Using a torx wrench, install the airbag sensor assembly
with 3 screws.
Torx wrench: T40 (Part No.09042±00020 or locally
manufactured tool)
Torque: 20 N´m (200 kgf´cm, 14 ft´lbf)
(b) Connect the airbag sensor connectors.
NOTICE:

Installation of the connector is done with the sensor
assembly installed. Make sure the sensor assembly
is installed to the specified torque.

If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.

When installing the senor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.

After installing , shake the sensor assembly to check
that there is no looseness.
2. INSTALL THESE PARTS: (See page BO±97)
(a) No.1 console box duct
(b) No.3 console box mounting bracket
(c) Console box
(d) Console box register
(e) Rear console armrest
(f) Lower rear console box
(g) Accessary case
(h) Accessary socket
(i) Console box carpet
(j) Cluster finish panel
(k) Front ash receptacle
(l) Glove compartment panel assembly
(m) Glove compartment finish plate
(n) No.2 under cover
(o) No.1 safety pad
(p) Hood lock release lever
(q) No.1 under cover
(r) End Pad
(s) Finish plate

RS07U±01
H02618
2JZ±GE Engine:
Air Cleaner Assembly
1UZ±FE Engine:
Air Cleaner AssemblyAir Cleaner Inlet No.1
ECU Box Upper Cover
ECU Box Front Airbag
Sensor RH
Front Airbag Sensor LH
7.8 (80, 69 in.´lbf)
7.8 (80, 69 in.´lbf)
: Specified torqueN´m (kgf´cm, ft´lbf)

Non±reusable part



± SUPPLEMENTAL RESTRAINT SYSTEMFRONT AIRBAG SENSOR
RS±57
2288 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
FRONT AIRBAG SENSOR
COMPONENTS

RS07Y±01
H02696
H02697
RS±62
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT AIRBAG SENSOR
2293 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSTALLATION
1. INSTALL FRONT AIRBAG SENSOR
Install the sensor with bolt and nut, then connect the connector.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
NOTICE:

Make sure the sensor is installed to the specified
torque.

If the sensor has been dropped, or there are cracks,
dents or other defects in the case, brackets or con-
nector, replace the removed sensor. Always replace
the set bolt and nut with new ones.

The sensor set bolt and nut have been anti±rust
treated. When the sensor is removed, always replace
the set bolt and nut with new ones.

After installation, shake the sensor to check that
there is no looseness.

The front sensor is equipped with an electrical con-
nection check mechanism. Be sure to lock this mech-
anism securely when connecting the connector. If the
connector is not securely locked, a malfunction code
will be detected by the diagnostic system.
2. INSTALL REMOVED PARTS

RS07Z±01
H02617
Center Pillar Lower Garnish
Front Door Scuff Plate
Rear Door Scuff Plate
Side Airbag
Sensor Assembly
Front Seat
Outer Belt Retractor
41 (420, 30)
7.4 (75, 65 in.´lbf)
20 (200, 14)
: Specified torqueN´m (kgf´cm, ft´lbf)
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG SENSOR ASSEMBLY
RS±63
2294 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
SIDE AIRBAG SENSOR ASSEMBLY
COMPONENTS

RS083±01
H02619
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG SENSOR ASSEMBLY
RS±67
2298 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSTALLATION
NOTICE:

Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.

Never reuse the side airbag sensor assembly in-
volved in a collision when the airbag has deployed.

Never repair a sensor in order to reuse it.
1. INSTALL SIDE AIRBAG SENSOR
(a) Using a torx wrench, install the side airbag assembly with
4 screws.
Torx wrench: T40 (Part No.09042±00020 or locally
manufactured tool)
Torque: 20 N´m (200 kgf´cm, 14 ft´lbf)
(b) Connect the connector.
NOTICE:

Make sure the sensor assembly is installed to the
specified torque.

If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.

When installing the sensor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.

After installation, shake the sensor assembly to
check that there is no looseness.
2. INSTALL FRONT SEAT OUTER BELT RETRACTOR
(See page BO±132)
(a) Install the retractor with 2 bolts.
HINT:
After tightening the upper bolt, tighten the lower bolt.
Torque:
Upper bolt: 7.4 N´m (75 kgf´cm, 65 in.´lbf)
Lower bolt: 41 N´m (420 kgf´cm, 30 ft´lbf)
(b) w/ Seat Belt Warning:
Connect the retractor switch connector.
(c) w/ Seat Belt Pretensioner:
Connect the pretensioner connector.
3. INSTALL THESE PARTS:
(a) Center pillar lower garnish
(b) Rear door scuff plate
(c) Front door scuff plate

SA0R6±01
F02311
R11097
F02313
SST
SA±10
± SUSPENSION AND AXLEFRONT AXLE HUB
2010 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE FRONT BRAKE CALIPER AND DISC
(a) Remove the 2 bolts and brake caliper from the steering
knuckle.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
(b) Support the brake caliper securely.
(c) Remove the disc.
3. CHECK BEARING BACKLASH AND AXLE HUB
DEVIATION
(a) Using a dial indicator near the center of the axle hub and
check the backlash in the bearing shaft direction.
Maximum: 0.05 mm (0.0020 in.)
If the blacklash exceeds the maximum, replace the bearing.
(b) Using a dial indicator, check the deviation at the surface
of the axle hub outside the hub bolt.
Maximum: 0.05 mm (0.0020 in.)
If the deviation exceeds the maximum, replace the axle hub.
4. REMOVE ABS SPEED SENSOR
Remove the bolt and ABS speed sensor.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
5. REMOVE STEERING KNUCKLE
(a) Remove the upper side of the clip and nut.
Torque: 87 N´m (890 kgf´cm, 64 ft´lbf)
(b) Using SST, remove the steering knuckle from the upper
suspension arm.
SST 09610±20012