2000 LEXUS GS400 low beam

I04079
Connector ºCº Connector ºDº
Connector ºFº Connector ºEº
Connector ºGº
1 131 13
1 201 12
± BODY ELECTRICALCOMBINATION METER
BE±93
2394 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
2. INSPECT COMBINATION METER CIRCUIT PLATE
Warning light circuit plate:
(a) Remove meter cover.
(b) Disconnect connectors ºCº, ºDº, ºEº, ºFº and ºGº from the
meter circuit plate and inspect the connectors on the wire
harness side as shown in the table.
Tester connectionCheck indicator lightSpecified condition
D10 (+) ± D12 (±)Fuel level warning lightContinuity
D6 (+) ± D8 (±)Headlight indiactor light (USA)
Taillight indiactor light (CANADA)Continuity
D2 (+) ± D4 (±)Hi±beam indicator lightContinuity
C3 (+) ± C7 (±)Engine oil level warning lightContinuity
C3 (+) ± C5 (±)Malfunction indicator lightContinuity
E19 (±) ± E20 (+)Slip warning lightContinuity
E18 (±) ± E20 (+)TRAC OFF indicator lightContinuity
E17 (±) ± E20 (+)Window washer level warning lightContinuity
E16 (±) ± E20 (+)ABS warning lightContinuity
E15 (±) ± E20 (+)VSC OFF indicator lightContinuity
E14 (±) ± E20 (+)Brake warning lightContinuity
E13 (±) ± E20 (+)ECT SNOW indicator lightContinuity
E12 (±) ± E20 (+)Low oil pressure warning lightContinuity
E11 (±) ± E20 (+)ECT PWR indicator lightContinuity
E10 (±) ± E20 (+)Discharge warning lightContinuity
E9 (±) ± E20 (+)CRUISE MAIN indicator lightContinuity
E8 (±) ± E20 (+)Seat belt warning lightContinuity
E7 (±) ± E20 (+)Rear Lights warning lightContinuity
E6 (±) ± E20 (+)Headlight leveling indiactorContinuity
E4 (+) ± E5 (±)SRS warning lightContinuity
E3 (±) ± E4 (+)Open door warning lightContinuity
F4 (±) ± F12 (+)A/T shift indicator light (L)Continuity
F11 (±) ± F12 (+)A/T shift indicator light (2)Continuity
F10 (±) ± F12 (+)A/T shift indicator light (3)Continuity
F8 (±) ± F12 (+)A/T shift indicator light (P)Continuity

Z03473
Ammeter
Battery
VoltmeterGenerator Disconnect Wire
from Terminal B
B01656
Terminal F
± CHARGING (2JZ±GE)CHARGING SYSTEM
CH±3
1605 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
7. CHECK CHARGE WARNING LIGHT CIRCUIT
(a) Warm up the engine and then turn it off.
(b) Turn off all accessories.
(c) Turn the ignition switch ºONº. Check that the charge warn-
ing light is lit.
(d) Start the engine. Check that the light goes off.
If the light does not go off as specified, troubleshoot the charge
light circuit.
8. INSPECT CHARGING CIRCUIT WITHOUT LOAD
HINT:
If a battery/generator tester is available, connect the tester to
the charging circuit as per manufacturer's instructions.
(a) If a tester is not available, connect a voltmeter and amme-
ter to the charging circuit as follows:

Disconnect the wire from terminal B of the genera-
tor, and connect it to the negative (±) probe of the
ammeter.

Connect the positive (+) probe of the ammeter to
terminal B of the generator.

Connect the positive (+) probe of the voltmeter to
terminal B of the generator.

Ground the negative (±) probe of the voltmeter.
(b) Check the charging circuit as follows:
With the engine running from idling to 2,000 rpm, check
the reading on the ammeter and voltmeter.
Standard amperage: 10 A or less
Standard voltage: 13.2 ± 14.8 V
If the voltmeter reading is more than standard voltage, replace
the voltage regulator.
If the voltmeter reading is less than standard voltage, check the
voltage regulator and generator as follows:

With terminal F grounded, start the engine and
check the voltmeter reading of terminal B.

If the voltmeter reading is more than standard volt-
age, replace the voltage regulator.

If the voltmeter reading is less than standard volt-
age, check the generator.
9. INSPECT CHARGING CIRCUIT WITH LOAD
(a) With the engine running at 2,000 rpm, turn on the high
beam headlights and place the heater blower switch at
ºHIº.
(b) Check the reading on the ammeter.
Standard amperage: 30 A or more
If the ammeter reading is less than the standard amperage, re-
pair the generator.
HINT:
If the battery is fully charged, the indication will sometimes be
less than standard amperage.

SS0CN±02
SS±60
± SERVICE SPECIFICATIONSBODY ELECTRICAL
216 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
BODY ELECTRICAL
SERVICE DATA
DAYTIME RUNNING LIGHT RELAY (MAIN) (Wire Harness Side)
1 ± Ground (Ignition switch position LOCK or ACC)No voltage
1 ± Ground (Ignition switch position ON or START)Battery positive voltage
5 ± Ground (Engine Stop)No voltage
5 ± Ground (Engine Running)Battery positive voltage
7 ± Ground (Constant)Battery positive voltage
9 ± Ground (Constant)Battery positive voltage
AUTOMATIC LIGHT CONTROL SENSOR
(Connector disconnected)
4 ± Ground (Ignition switch position LOCK or ACC)No voltage
4 ± Ground (Ignition switch position ON)5.2 ± 9.0 V
(Connector connected)
1 ± Ground (Ignition switch position LOCK or ACC)No voltage
1 ± Ground (Ignition switch position ON)9.5 V or more
HEADLIGHT BEAM LEVEL CONTROL ECU
(Connector disconnected)
A1 ± A5 (Ignition switch position OFF)26 ± 30 W
A1 ± A6 (Ignition switch position OFF)26 ± 30 W
A1 ± A7 (Ignition switch position OFF)26 ± 30 W
A1 ± A8 (Ignition switch position OFF)26 ± 30 W
A4 ± B4 (Ignition switch position ON and light control switch HEAD)Below 1.5 V
B1 ± B3 (Ignition switch position OFF)3.5 k ± 6.5 kW
B5 ± B7 (Ignition switch position OFF)3.5 k ± 6.5 kW
(Connector disconnected)
B2 ± B3 (Ignition switch position ON)Approx. 2.5 V
B6 ± B7 (Ignition switch position ON)Approx. 2.5 V
B1 ± B3 (Ignition switch position ON)5V
B5 ± B7 (Ignition switch position ON)5V
TURN SIGNAL FLASHER
1 ± Ground (Ignition switch position LOCK or ACC)No voltage
1 ± Ground (Ignition switch position ON)Battery positive voltage
4 ± Ground (Constant)Battery positive voltage
LIGHT FAILURE RELAY (Wire Harness Side)
5 ± Ground (Light control switch position OFF)No voltage
5 ± Ground (Light control switch position TAIL or HEAD)Battery positive voltage
8 ± Ground (Ignition switch position LOCK or ACC)No voltage
8 ± Ground (Ignition switch position ON)Battery positive voltage
9 ± Ground (Stop light switch position OFF)No voltage
9 ± Ground (Stop light switch position ON)Battery positive voltage
10 ± Ground (Stop light switch position OFF)No voltage
10 ± Ground (Stop light switch position ON)Battery positive voltage
SPEEDOMETER (ON±VEHICLE)
USA: