2000 CHRYSLER CARAVAN relay

TEST TC-40AREPAIRING - FAN CONTROL OPEN CIRCUIT FAN 2
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
KEY ON. ARE THE RADIATOR
START TEST WITH THE DRB, FAN RELAYS #1 AND NO CONTINUE TEST
TC-40A. ACTUATE THE HIGH #3 CLICKING ON AND TC-40A ON THE
SPEED RADIATOR OFF? NEXT PAGE.
FAN.
YES
THE CONDITION TO SET USING THE SCHEMATIC
THE TROUBLE CODE IS AS A GUIDE, INSPECT WERE ANY PROBLEMS YES REPAIR AS
NOT PRESENT. THE WIRING AND FOUND? NECESSARY.*
CONNECTORS.
FIG.1 FIG.2
NO
WIGGLE THE WIRING REPAIR AS
HARNESS FROM THE NOTE: THE DRB MUST DID THE WIGGLING YES NECESSARY WHERE
RELAYS TO THE STILL BE ACTUATING INTERRUPT FAN WIGGLING CAUSED
ENGINE CONTROL THE FAN RELAY. RELAY CLICKING? RELAY CLICKING TO
MODULE.BE INTERRUPTED.*
NO
REFER TO GENERAL
INFORMATION 3.3.2
FOR ADDITIONAL TEST COMPLETED.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
149
ProCarManuals.com

TEST TC-40ACONTINUED - REPAIRING - FAN CONTROL OPEN CIRCUIT FAN 2
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-40A TURN IGNITION OFF.
CONTINUED FROM
THE PREVIOUS REMOVE RADIATOR FAN
PAGE. RELAYS #1 AND #3.**
TURN IGNITION ON. MEASURE THE DIESEL IS THE VOLTAGE
POWER RELAY OUTPUT ABOVE 10.0 VOLTS NO REPAIR THE OPEN
USE A VOLTMETER IN CIRCUIT AT EACH FOR EACH DIESEL POWER RELAY
THE FOLLOWING RELAY CONNECTOR. MEASUREMENT? OUTPUT CIRCUIT.*
STEP. FIG.1 AND 2
YES
TURN IGNITION OFF. MEASURE THE IS THE RESISTANCE REPLACE THE
RESISTANCE BETWEEN BELOW 100.0 OHMS NO RADIATOR FAN RELAY
USE AN OHMMETER IN TERMINALS 85 AND FOR EACH THAT MEASURED
THE FOLLOWING 86 OF THE #1 AND MEASUREMENT? ABOVE 100.0 OHMS.*
STEPS. #3 RELAYS. FIG.3
YES
KEY OFF. MEASURE THE REPAIR THE HIGH
DISCONNECT THE ECM RESISTANCE BETWEEN IS THE RESISTANCE YES SPEED FAN CONTROL
HARNESS GROUND AND ECM BELOW 5.0 OHMS? CKT FOR A SHORT TO
CONNECTORS.** HARNESS CONNECTOR GROUND.*
CAVITY 41. FIG.4
NO
MEASURE THE FROM EACH RELAY TO
RESISTANCE OF THE ECM HARNESS IS THE RESISTANCE NO REPAIR OPEN HIGH
HIGH SPEED FAN CONNECTOR CAVITY 41. BELOW 5.0 OHMS FOR SPEED FAN CONTROL
CONTROL CIRCUIT... EACH MEASUREMENT? CIRCUIT.*
FIG.1, 2 AND 4
YES
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
151
ProCarManuals.com

TEST TC-41AREPAIRING - FAN CONTROL SHORT CIRCUIT FAN 1
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
KEY ON. IS THE RADIATOR
START TEST WITH THE DRB, FAN #2 RELAY NO CONTINUE TEST
TC-41A. ACTUATE THE LOW CLICKING ON AND TC-41A ON THE
SPEED RADIATOR OFF? NEXT PAGE.
FAN.
YES
THE CONDITION TO SET USING THE SCHEMATIC
THE TROUBLE CODE IS AS A GUIDE, INSPECT WERE ANY PROBLEMS YES REPAIR AS
NOT PRESENT. THE WIRING AND FOUND? NECESSARY.*
CONNECTORS.
FIG.1 FIG.2
NO
WIGGLE THE WIRING REPAIR AS NECESSARY
HARNESS FROM THE NOTE: THE DRB MUST DID THE WIGGLING YES WHERE WIGGLING
RELAY TO THE STILL BE ACTUATING INTERRUPT FAN CAUSED FAN RELAY
ENGINE CONTROL THE FAN RELAY. RELAY CLICKING. CLICKING TO BE
MODULE.INTERRUPTED.*
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETED.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
153
ProCarManuals.com

TEST TC-41ACONTINUED - REPAIRING - FAN CONTROL SHORT CIRCUIT FAN 1
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-41A
CONTINUED FROM REMOVE RADIATOR
THE PREVIOUS FAN RELAY #2.**
PAGE.
USING AN OHMETER, 85 AND 86 IS THE RESISTANCE
MEASURE RESISTANCE 85 AND 30 BELOW 30.0 OHMS YES REPLACE RADIATOR
BETWEEN RADIATOR 85 AND 87. FOR ANY OF THE FAN RELAY #2.*
FAN #2 RELAY MEASUREMENTS?
TERMINALS... FIG.1
NO
TURN IGNITION OFF.
DISCONNECT THE ECM REMOVE DIESEL
HARNESS POWER RELAY.**
CONNECTORS.**
WITH A JUMPER WIRE,
CONNECT DIESEL POWER
RELAY CONN. CAVITIES TURN IGNITION ON.
30 AND 87 (IN PDC).
FIG.2
MEASURE THE RELAY REPAIR RADIATOR
USE A VOLTMETER IN CONTROL CIRCUIT AT IS THE VOLTAGE YES FAN RELAY #2
THE FOLLOWING ECM HARNESS ABOVE 1.0 VOLT? CONTROL CIRCUIT
STEP. CONNECTOR CAVITY 17. FOR SHORT TO
FIG. 3 VOLTAGE.*
NO
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
155
ProCarManuals.com

TEST TC-42AREPAIRING - FAN CONTROL SHORT CIRCUIT FAN 2
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
KEY ON. ARE THE RADIATOR
START TEST WITH THE DRB, FAN RELAYS #1 AND NO CONTINUE TEST
TC-42A. ACTUATE THE HIGH #3 CLICKING ON AND TC-42A ON THE
SPEED RADIATOR OFF? NEXT PAGE.
FAN.
YES
THE CONDITION TO SET USING THE SCHEMATIC
THE TROUBLE CODE IS AS A GUIDE, INSPECT WERE ANY PROBLEMS YES REPAIR AS
NOT PRESENT. THE WIRING AND FOUND? NECESSARY.*
CONNECTORS.
FIG.1. FIG.2
NO
WIGGLE THE WIRING REPAIR AS
HARNESS FROM THE NOTE: THE DRB MUST DID THE WIGGLING YES NECESSARY WHERE
RELAYS TO THE STILL BE ACTUATING INTERRUPT FAN WIGGLING CAUSED
ENGINE CONTROL THE FAN RELAY. RELAY CLICKING? RELAY CLICKING TO
MODULE.BE INTERRUPTED.*
NO
REFER TO GENERAL
INFORMATION 3.3.2
FOR ADDITIONAL TEST COMPLETED.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
157
ProCarManuals.com

TEST TC-42ACONTINUED - REPAIRING - FAN CONTROL SHORT CIRCUIT FAN 2
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-42A
CONTINUED FROM REMOVE RADIATOR
THE PREVIOUS FAN RELAYS
PAGE. #1 AND #3.**
USING AN OHMETER, 85 AND 86, 85 AND IS THE RESISTANCE
MEASURE RESISTANCE 30, 85 AND 87. BELOW 30.0 OHMS YES REPLACE SHORTED
BETWEEN RADIATOR REPEAT MEASUREMENTS FOR ANY OF THE RADIATOR FAN
FAN #1 RELAY ON RADIATOR FAN MEASUREMENTS? RELAY.*
TERMINALS... RELAY #3. FIG.1
NO
TURN IGNITION OFF.
DISCONNECT THE ECM REMOVE THE DIESEL
HARNESS POWER RELAY.**
CONNECTORS.**
WITH A JUMPER WIRE,
CONNECT DIESEL POWER
RELAY CONN. CAVITIES TURN IGNITION ON.
30 AND 87 (IN PDC).
FIG.2
MEASURE THE RELAY REPAIR RADIATOR
USE A VOLTMETER IN CONTROL CIRCUIT AT IS THE VOLTAGE YES FAN RELAY #1 AND
THE FOLLOWING ECM HARNESS ABOVE 1.0 VOLT? #3 CONTROL CIRCUIT
STEP. CONNECTOR CAVITY 41. FOR A SHORT TO
FIG.3 VOLTAGE.*
NO
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
159
ProCarManuals.com

TEST TC-51AREPAIRING - GLOW RELAY #1 CONTROLLER OPEN CIRCUIT
Perform TEST DTC Before Proceeding
FIG.1
FIG.2
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
184
ProCarManuals.com

TEST TC-51AREPAIRING - GLOW RELAY #1 CONTROLLER OPEN CIRCUIT
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST WITH THE DRB, IS THE GLOW PLUG NO CONTINUE
TC-51A. ACTUATE GLOW PLUG #1 RELAY CLICKING? TEST-51A ON THE
#1 RELAY. NEXT PAGE.
YES
THE CONDITION TO SET USING THE SCHEMATIC
THE TROUBLE CODE IS AS A GUIDE, INSPECT WERE ANY PROBLEMS YES REPAIR AS
NOT PRESENT. THE WIRING AND FOUND? NECESSARY.*
CONNECTORS.
FIG.1 FIG.2
NO
WIGGLE THE WIRING NOTE: THE DRB MUST REPAIR AS
HARNESS FROM THE STILL BE ACTUATING DID THE WIGGLING YES NECESSARY WHERE
GLOW PLUG #1 RELAY THE GLOW PLUG #1 INTERRUPT THE WIGGLING CAUSED
TO THE ENGINE RELAY. CLICKING? CLICKING TO BE
CONTROL MODULE.INTERRUPTED.*
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETED.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
185
ProCarManuals.com