2000 CHRYSLER CARAVAN relay

TEST NS-2AREPAIRING A NO RESPONSE CONDITION
Perform TEST NS-SEL Before Proceeding
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
START TEST DOES THE VEHICLE YES PERFORM TEST
NS-2A. START? NS-2B.
NO
KEY OFF. WITH AN OHMMETER, IS THE RESISTANCE
MEASURE RESISTANCE ABOVE 5.0 OHMS FOR YES REPAIR THE OPEN
DISCONNECT THE ECM OF THE PCM GND CKTS ANY OF THE ECM GROUND.*
HARNESS AT HARNESS CAVITIES MEASUREMENTS?
CONNECTORS.** 1 AND 27. FIG.1
NO
KEY ON. USING A AT ECM HARNESS REPAIR OPEN OR
VOLTMETER, MEASURE CONNECTOR CAVITY 47. IS THE VOLTAGE NO SHORT TO GROUND IN
THE FUSED IGNITION ABOVE 10.0 VOLTS? THE FUSED IGNITION
SWITCH OUTPUT SWITCH OUTPUT
CIRCUIT... FIG.1 CIRCUIT.*
YES
KEY OFF. USING A VOLTMETER REPAIR OPEN FUSE
REMOVE THE DIESEL PROBE DIESEL POWER IS THE VOLTAGE NO OR FUSED BATTERY
POWER RELAY. RELAY CONNECTOR ABOVE 10.0 VOLTS? CIRCUIT TO DIESEL
CAVITY 30 (IN PDC). POWER RELAY.*
KEY ON. FIG.2
YES
KEY OFF. CONNECT A MEASURE VOLTAGE AT IS THE VOLTAGE
JUMPER WIRE ACROSS ECM HARNESS ABOVE 10.0 VOLTS NO REPAIR OPEN DIESEL
RELAY CONNECTOR CONNECTOR CAVITIES FOR EACH POWER RELAY OUTPUT
CAVATIES 30 AND 87. 2 AND 28. MEASUREMENT? CIRCUIT(S).*
FIG. 1 AND 2
YES
KEY OFF. RECONNECT WITH JUMPER WIRE
THE ENGINE CONTROL STILL CONNECTED, DOES THE VEHICLE NO REPLACE THE ENGINE
MODULE HARNESS ATTEMPT TO START START? CONTROL MODULE.*
CONNECTORS. VEHICLE.
YES
CONTINUE TEST
NS-2A ON THE
NEXT PAGE.
N
O
R
E
S
P
O
N
S
E
T
E
S
T
401
ProCarManuals.com

TEST NS-2ACONTINUED - REPAIRING A NO RESPONSE CONDITION
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
PROBE DIESEL POWER
RELAY CONNECTOR
CAVITY 86 (IN PDC).
FIG.1
CONNECT A JUMPER
WIRE BETWEEN ECM
HARNESS CONNECTOR
CAVITY 33 AND
GROUND.
FIG. 4
N
O
R
E
S
P
O
N
S
E
T
E
S
T
403
ProCarManuals.com

TEST NS-2ACONTINUED - REPAIRING A NO RESPONSE CONDITION
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
TEST NS-2A USING A JUMPER
CONTINUED FROM WIRE, CONNECT
THE PREVIOUS DIESEL POWER RELAY
PAGE. CAVITIES 30 AND 87
(IN PDC). FIG. 1
USING A VOLTMETER, REPAIR THE DIESEL
MEASURE THE DIESEL IS THE VOLTAGE YES POWER RELAY
POWER RELAY ABOVE 1.0 VOLT? CONTROL CIRCUIT
CONTROL CKT. FOR A SHORT TO
FIG. 1 VOLTAGE.*
NO
REPLACE THE DIESEL
POWER RELAY.*
N
O
R
E
S
P
O
N
S
E
T
E
S
T
405
ProCarManuals.com

TEST VER-2AROAD TEST VERIFICATION
Inspect the vehicle to ensure that all engine components are connected. Reassemble and reconnect
all components as necessary.
If this verification procedure is being performed after a NO TROUBLE CODE test, do the
following:
1. Check to see if the initial symptom still exists.
2. If the initial or another symptom exists, the repair is not complete. Check all pertinent Technical
Service Bulletins and return toTEST NTC-1Aif necessary.
For previously read trouble codes that have not been dealt with, return toDTC TESTand follow the
path specified; otherwise, continue.
If the engine control module has not been changed:
1. Connect the DRB to the data link connector and erase trouble codes.
2. With the DRB, reset all values in the adaptive memory.
3. Disconnect the DRB.
4. Turn the ignition off for at least 10 seconds.
Ensure no trouble code remains by doing the following:
1. If this test is for anA/C Relay Control Circuit,drive the vehicle for at least five minutes with
the A/C on. For some of the drive, go at least 40 mph; at some point stop the car and turn the
engine off for 10 seconds or more then restart and continue. Upon completion of the road test,
turn the engine off, and read trouble codes with the DRB.
2. If the repaired code has reset, the repair is not complete. Check all related Technical Service
Bulletins and return toDTC TESTif necessary. If another trouble code has set, return toDTC
TESTand follow the path specified for that trouble code. If there are no trouble codes, the
repair was successful and is now complete.
V
E
R
I
F
I
C
A
T
I
O
N
T
E
S
T
423
ProCarManuals.com