1999 TOYOTA CAMRY Seatback

BO0LD±01
H01747
Torsion Bar
Luggage Compart-
ment Door Hinge
Luggage Compart-
ment Door Hinge
Luggage Compartment
Door
Luggage Compartment
Door Trim
Left Side Luggage
Trim
Finish Side Trim
Rear Luggage Trim
Rear Seat CushionRoom Partition TrimPackage Tray Trim
High Mounted
Stop Light
Rear SeatbackFinish Side Trim Door Lock
Door Lock StrikerLeft Hand Back
Up LightRight Hand
Back Up Light Right Side Luggage
Trim
: Specified torque
N´m (kgf´cm, ft´lbf)
Lock Cylinder
Luggage Compart-
ment Floor Mat
8.0 (80, 71 in.´lbf)
8.0 (80, 71 in.´lbf)
5.5 (55, 49 in.´lbf)
5.5 (55, 49 in.´lbf)
± BODYLUGGAGE COMPARTMENT DOOR AND HINGE
BO±27
2375 Author: Date:
LUGGAGE COMPARTMENT DOOR AND HINGE
COMPONENTS

BO0LR±01
N20948
Back Window Moulding
Back Window Glass

Dam
Roof Side
Inner GarnishRear Seatback
19 (185, 13)
42 (420, 31)
Rear Side Seat
Back RH Rear Side Seat
Back LH
Rear Seat Cushion
19 (185, 13)
19 (185, 13)
Rear Seat Center BeltRear Seat Outer BeltHigh±Mounted
Stop Light
Package Tray
Trim
Rear Seat Outer Belt
Room Partition Trim

Non±reusable part
N´m (kgf´cm, ft´lbf): Specified torque
± BODYBACK WINDOW GLASS
BO±49
2397 Author: Date:
BACK WINDOW GLASS
COMPONENTS

BO0LS±01
N21020
3 Clips
1 Clip
N22588
N21021
4 Clips
N21121
N20985
BO±50
± BODYBACK WINDOW GLASS
2398 Author: Date:
REMOVAL
1. REMOVE REAR SEAT CUSHION AND SEATBACKS
2. REMOVE ROOF SIDE INNER GARNISHES
(a) Remove the clips.
(b) Pull the garnish to remove it.
3. REMOVE HIGH±MOUNTED STOP LIGHT
(a) Push on the both side of the cover to release the claws by
your hand and remove the cover as shown in the illustra-
tion.
(b) Remove the 2 bolts and stop light, then disconnect the
connector.
4. REMOVE PACKAGE TRAY TRIM
(a) Remove the bolts holding the rear seat belt lower side to
the body.
(b) Remove the seat belts with seat belt hole covers from the
package trim.
(c) Remove the trim by pulling forward.
5. REMOVE ROOM PARTITION TRIMS
Remove the 6 clips and room partition trims.
6. REMOVE THESE PARTS
(a) Assist grips.
(b) Rear side of roof headlining.
7. DISCONNECT DEFOGGER WIRE CONNECTORS
8. REMOVE BACK WINDOW MOULDING
Using a knife, cut off the moulding as shown.
NOTICE:
Do not damage the body with the knife.
9. REMOVE BACK WINDOW GLASS
Remove the glass in the same way as windshield.
(See page BO±43)

BO±52
± BODYBACK WINDOW GLASS
2400 Author: Date:
(d) Room partition trims
(e) Seat belt lower side bolts
Torque: 42 N´m (420 kgf´cm, 31 ft´lbf)
(f) High±mounted stop light
(g) Roof side inner garnish
(h) Rear seatbacks and seat cushion
Torque: 18 N´m (185 kgf´cm, 13 ft´lbf)

BO0MG±01
N22600


Assist Grip
Sun VisorRoof Headlining
Assist Grip
Room Light Map Light
Assembly
Holder
Cover
Holder
Sun Visor
Center Pillar Garnish
Roof Side Inner Garnish Front Pillar Garnish
Front Door Scuff
PlateLower Center
Pillar GarnishRear Side Seat
Back RH
42 (420, 31)
Rear Seat
Side GarnishRear Seatback
Rear Side Seat
Back LH
42 (420, 31)
18 (185, 13)
18 (185, 13)
18 (185, 13)
Rear Seat Cushion
Center Pillar Garnish
42 (420, 31)
42 (420, 31)
Roof Seat
Side Garnish
Front Pillar Garnish
Rear Seat
Side Garnish
Lower Center
Pillar Garnish
42 (420, 31)
Front Door Scuff
Plate
N´m (kgf´cm, ft´lbf): Specified torque BO±82
± BODYROOF HEADLINING
2430 Author: Date:
ROOF HEADLINING
COMPONENTS

BO0MH±01
N21457
: 4 Clips
N21458
: Clip
: 2 Clips
N21415
± BODYROOF HEADLINING
BO±83
2431 Author: Date:
REMOVAL
1. REMOVE THESE PARTS:
(a) Rear seat cushion
(b) Rear seatback and rear side seatbacks
(c) Front door scuff plates
(d) Front seat belt shoulder anchor bolts
(e) Sun visor and holders
(f) Assist grips
(g) Front pillar garnishes
(h) Rear door scuff plates
(i) Lower center pillar garnishes
2. REMOVE ROOF SIDE INNER GARNISH
(See page BO±28)
3. REMOVE FRONT PILLAR GARNISH
(a) Pry out clips by your hand.
(b) Pull the garnish upward to remove it.
4. REMOVE CENTER PILLAR GARNISH
(a) Remove the clip.
(b) Pry off the garnish.
5. REMOVE ROOM LIGHT
(a) Using a screwdriver, remove the room light cover.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 4 screws, then disconnect the connector.
6. REMOVE MAP LIGHT ASSEMBLY

BO0MJ±01
H01977
Headrest
Seatback Frame
w/ Side Airbag Assembly
Side Airbag Assembly Headrest Support

Hog Ring
Seatback Pad Seatback Cover
Seat Cushion Cover
Seat Cushion Pad
Seat Cushion Frame
Hog RingLumber Support Adjuster
Power Seat Adjuster
Seat Cushion Shield
Switch Knob Front Vertical
Motor
Lower Seat Cushion ShieldHinge Cover
Power Seat Switch
: Specified torque
N´m (kgf´cm, ft´lbf)

Non±reusable part
37 (375, 27)
37 (375, 27)
Rear Vertical Motor
Seat Track Cover
Reclining Motor
15 (150, 11)
6.0 (61, 53 in.´lbf)
18 (185, 13)
BO±86
± BODYFRONT SEAT (Power Seat for TMC Made)
2434 Author: Date:
FRONT SEAT (Power Seat for TMC Made)
COMPONENTS

BO0ML±01
H01870
BO±88
± BODYFRONT SEAT (Power Seat for TMC Made)
2436 Author: Date:
DISASSEMBLY
1. REMOVE THESE PARTS:
(a) Headrest
(b) Switch knobs
(c) Seat cushion shield
(d) Lower seat cushion shield
(e) Power seat switch
2. REMOVE SEATBACK ASSEMBLY
(a) Remove the 3 clips of the side airbag wire harness from
the seat cushion frame.
(b) Remove the 4 bolts and seatback assembly.
3. REMOVE SEATBACK COVER
(a) Remove the hog rings and hooks.
(b) Remove the hook as shown in the illustration.
(c) Remove the headrest supports.
(d) Remove the hog rings and seatback frame from seatback
cover with pad.
(e) Remove the hog rings and seatback cover from seatback
pad.
4. REMOVE SIDE AIRBAG ASSEMBLY
Remove the 1 clip of side airbag wire harness, 2 nuts and side
airbag assembly from the seatback frame.
CAUTION:

Do not store the side airbag assembly with the airbag
deployment direction facing down.

Never disassemble the side airbag assembly.
5. REMOVE LUMBER SUPPORT ADJUSTER
Remove the 2 screws and lumber support adjuster.
6. REMOVE SEAT CUSHION ASSEMBLY
Remove the 4 bolts and seat cushion assembly.
7. REMOVE SEAT CUSHION COVER
(a) Remove the 2 clips, hook and seat cushion frame from
seat cushion cover with pad.
(b) Remove the hog rings and seat cushion cover from the
seat cushion pad.