1999 TOYOTA CAMRY belt

SEAT BELT EXTENDER: '99 ± '01 MODEL YEAR ± BO020±00 August 11, 2000
Page 5 of 7
PART NUMBER PREFIX: 73399±
SERIESLENGTHSERIES6 INCH9 INCH12 INCH15 INCH18 INCH
R±5±16060±16070±16080±16090±16100
N±1±12060±12070±12080±12090±12100
N±5±20110±20120±20130±20140±20150
N±6±20160±20170±20180±20190±20200
N±7±47010±47020±47030±47040±47050
K±5±35010±35020±35030±35040±35050
A±2±01060*1±01070±01080±01090±01100
Q±2±06010±06020±06030±06040±06050
Q±4±0W010±0W020±0W030±0W040±0W050
S±1±04010±04020±04030±04040±04050
T±1±01110±01120±01130±01140±01150
*1 Length: 7 1/4º
Parts
Information

SEAT BELT EXTENDER: '99 ± '01 MODEL YEAR ± BO020±00 August 11, 2000
Page 6 of 7
Failure to follow the recommendations indicated below could result in less effectiveness
of the seat belt restraint system in case of vehicle collision, causing personal injury.
The Seat Belt Extender must not be used:
a. By anyone other than for whom it was provided (name recorded on seat belt
extender).
b. In any vehicle and/or seat position other than the one for which it was
provided.
c. When the Seat Belt Extender is provided for rear seat positions (with
automatic locking retractor), make sure the retractor is locked when in use.
If your seat belt cannot be fastened securely because it is not long enough, a
personalized seat belt extender is available from your Toyota dealer free of charge.
Please contact your local Toyota dealer so that the dealer can order the proper required
length for the extender. Bring the heaviest coat you expect to wear for proper
measurement and selection of length. Additional ordering information is available at your
Toyota dealer.
CAUTION:
When using the seat belt extender, observe the following. Failure to follow these
instructions could result in less effectiveness of the seat belt restraint system in case
of vehicle accident, increasing the chance of personal injury.
Never use the Seat Belt Extender if you can comfortably fasten the seat belt
without it.
The Seat Belt Extender must never be used with any child safety seats.
Remember that the extender provided for you may not be safe when used on a
different vehicle, or for another person or at a different seating position than the
one originally intended for.
To connect the extender to the seat
belt, insert the tab into the seat belt
buckle so that the ªPRESSº signs on
the buckle±release buttons of the
extender and the seat belt are both
facing outward as shown.
You will hear a click when the tab locks
into the buckle.
When releasing the seat belt, press on
the buckle±release button on the
extender, not
on the seat belt. This helps
prevent damage to the vehicle interior
and extender itself.
When not in use, remove the extender and
store in the vehicle for future use.
Owner
Instructions
Seat Belt Extender
Seat Belt Release

SEAT BELT EXTENDER: '99 ± '01 MODEL YEAR ± BO020±00 August 11, 2000
Page 7 of 7
SEAT BELT EXTENDER WORKSHEET
PLEASE COPY THIS ORIGINAL WORKSHEET FOR EACH EXTENDER NEEDED
CAUTION:
To minimize the chance and/or severity of injury in an accident, the seat belt
extender must only be used:
1 By the person for whom it was provided
2 In the seat position for which it was provided
The seat belt extender must never be used with any child safety seats.
When the seat belt extender is provided for rear seat positions (with automatic
locking retractor), make sure the retractor is locked when extender belt is in use.
DEALER
SEAT BELT EXTENDER APPLICATIONAPPLICANT
DEALER CODEDEALER NAMEAPPLICANT NAME
ADDRESSADDRESS
CITY & STATEZIPCITY & STATEZIPPHONE
EMPLOYEE NAMEMODEL YEARBODY TYPESEATING POSITIONVEHICLE IDENTIFICATION NUMBER
DIRECTIONS FOR DETERMINING PROPER EXTENDER LENGTH
1.Place the seat in the position the applicant normally uses
2.With applicant in the seat, wearing thickest coat expected to be worn, pull belt all the way out and try to buckle
belt
If the belt latches into buckle and feels comfortable against upper chest area, an extender is not needed.
If belt does not buckle continue with step 3
If buckle latches but belt has no slack remaining, continue with step 3
3.Measure distance between applicant's navel and seat belt buckle (dimension A) and enter on worksheet
4.With belt all the way out, measure distance between latch tip and buckle tip (dimension B) and enter on
worksheet
NOTE: If belt latches but there is no slack enter zero as dimension B
5.Subtract dimension B from dimension A and record number in check number box on worksheet
6.Seat belt extender length is dimension B rounded up to next extender length (without exceeding check number)
NOTE: If extender length exceeds check number, an extender can not be provided to the
customer
Dimension A:
NAVEL TO BUCKLEDimension B:
LATCH TO BUCKLE
BuckleBuckle NavelLatch
A
B
SEAT BELT EXTENDER CALCULATION
DIMENSION A:DIMENSION B:CHECK NUMBER:
SEAT BELT EXTENDER AUTHORIZATION
The same seat belt extender can be used for right and left seating applications. Each seat belt extender will have
a label identifying the owner, VIN and seating position. Seat belt extenders are available only in black.
Applicant's Signature: _________________________________________ Date: ______________________
(Actual user of seat belt extender)

Toyota Supports ASE CertificationPage 1 of 4
BO026-01Title:
SHOULDER BELT ANCHOR TAPE SET
Models:
All Applicable Avalon, Camry, Corolla,
Previa & Sienna
Technical Service
BULLETIN
October 19, 2001

To assist customers in preventing particle buildup and preserve the appearance of the
shoulder belt anchor, the following procedure has been developed.
1996 ± 1999 model year Avalon vehicles.
1996 ± 2001 model year Camry vehicles.
1993 ± 2001 model year Corolla vehicles.
1996 ± 1997 model year Previa vehicles.
1998 ± 2001 model year Sienna
*1 vehicles.
*1Except rear seat belt.
CURRENT PART NUMBERPART NAME
73205±48011Tape Set, Shoulder Belt Anchor
NOTE:
The above tape set contains the fluorocarbon resin tape (2 pieces) and Velcro tape (1 piece).
OP CODEDESCRIPTIONTIMEOPNT1T2
BD1011Clean the Shoulder Belt Anchor0.373210±#####±##*1
73220±#####±##*16199
*1
OPN should be part number of whichever belt assembly that the procedure is performed on.
Applicable Warranty*:
This repair is covered under the Toyota Comprehensive Warranty. This warranty is in
effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's
in-service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
BODY
Introduction
Applicable
Vehicles
Parts
Information
Warranty
Information

October 19, 2001SHOULDER BELT ANCHOR TAPE SET ± BO026-01
Page 2 of 4
1. CLEAN SHOULDER BELT ANCHOR
NOTE:
Do not install the tape when the
vehicle temperature is below the
freezing point.
Do not re±use removed fluorocarbon
resin tape.
A. Pull out the seat belt about 300
mm and attach a clip as shown in
the illustration.
HINT:
Preventing the seat belt from retraction
with a clip will make the following
work easier.
B. Put the Velcro tape (in the parts
kit) through the hole of the
shoulder belt anchor,
brush±shaped side to the anchor.
C. Pull both ends of the Velcro tape
with your hand and shave off the
dirt on the shoulder belt anchor by
moving the Velcro tape several
times as shown in the illustration.
NOTE:
Remove the dirt completely. Otherwise,
the fluorocarbon resin tape may not
adhere properly. Installation
Procedure

October 19, 2001SHOULDER BELT ANCHOR TAPE SET ± BO026-01
Page 3 of 4
2. INSTALL FLUOROCARBON RESIN
TAPE
A. Place the fluorocarbon resin tape
onto the seat belt as shown in the
illustration.
NOTE:
Before installation of the fluorocarbon
resin tape, it is necessary to pre±release
the colored film about 5 mm for each
side. (Not fully released.)
B. By pulling up the seat belt, put the
fluorocarbon resin tape through
the hole of the shoulder belt
anchor. Match the shoulder belt
anchor to the center of the tape.
C. Remove the upper side colored
film from the fluorocarbon resin
tape, and securely affix the tape
to the outside of the shoulder belt
anchor.
D. Remove the lower side colored
film from the fluorocarbon resin
tape, and securely affix the tape
to the outside of the shoulder belt
anchor.
NOTE:
Be sure to affix the fluorocarbon
tape securely along all edges.
Pay attention not to make any
wrinkles or slack in the fluorocarbon
resin tape.
E. Remove the clip.
Installation
Procedure
(Continued)

October 19, 2001SHOULDER BELT ANCHOR TAPE SET ± BO026-01
Page 4 of 4
F. By pulling the seat belt up and
down several times, as shown in
the illustration, securely affix the
fluorocarbon resin tape and
confirm the smoothness of the
belt movement.
NOTE:
Affix the fluorocarbon resin tape on
the shoulder belt anchor to the other
side following the same procedure.
NOTE:
If the seat belt requires cleaning to
remove dirt, only use a neutral
detergent or lukewarm water to clean.
Use the seat belt after it is completely
dried, to confirm proper operation.
Installation
Procedure
(Continued)

WARRANTY PARTS MARKING PROCEDURE ± PG006-03September 26, 2003
Page 3 of 3
NOTE:
The following parts do not have to be marked unless the technician can determine
failure and location.
air induction/ejection systems fuel injection systems
all computers fuel injectors
alternators fuel pump
audio (internal) ignition system
batteries internal engine components
bearings internal transmission components
belts oil cooler
catalytic converter power door lock switches
crankshaft remanufactured parts
cruise control starters
distributors suspension components
EGR systems valve covers
engine control systems window regulators
exchange parts wiper motors
exhaust systems
Parts
Marking
List
(Continued)