1999 TOYOTA AVENSIS wheel torque

BE1367
Medium Current Fuse and High Current Fuse
Equal Amperage Rating
V00076
Abbreviation Part Name Symbol Illustration
FUSE
MEDIUM CURRENT FUSE
HIGH CURRENT FUSE
FUSIBLE LINK
CIRCUIT BREAKERFUSE
M–FUSE
H–FUSE
FL
CB
– INTRODUCTIONREPAIR INSTRUCTIONS
IN–5
(h) Carefully observe all specifications for bolt tightening
torques. Always use a torque wrench.
(i) Use of special service tools (SST) and special service ma-
terials (SSM) may be required, depending on the nature
of the repair. Be sure to use SST and SSM where speci-
fied and follow the proper work procedure. A list of SST
and SSM can be found in Preparation section in this
manual.
(j) When replacing fuses, be sure the new fuse has the cor-
rect amperage rating. DO NOT exceed the rating or use
one with a lower rating.
(k) Care must be taken when jacking up and supporting the
vehicle. Be sure to lift and support the vehicle at the prop-
er locations (See page IN–7).
(1) If the vehicle is to be jacked up only at the front or
rear end, make sure to place the stopper under the
wheels at the opposite end to block them in order to
ensure safety.

PP0MS–05
PP–18
– PREPARATIONSUPPLEMENTAL RESTRAINT SYSTEM
EQUIPMENT
Torque wrench
Tire Width: 185 mm (7.28 in.) Inner diam.: 360 mm (14.17 in.)Airbag disposal
Tire with disc wheel Width: 185 mm (7.28 in.)
Inner diam.: 360 mm (14.17 in.)Airbag disposal
Vinyl bagAirbag disposal

SS0G7–04
– SERVICE SPECIFICATIONSMANUAL TRANSAXLE (E251)
SS–7
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Transaxle upper side x Engine Bolt A
Bolt B64
29650
29647
21
Transaxle lower side x Engine Bolt A
Bolt B
Bolt C
Bolt D
Bolt E40
40
8
20
46408
408
82
204
47030
30
71 in.·lbf
15
34
Diesel throttle body x Engine unit2121415
No.1 air tube assembly x Engine unit2525518
Diesel throttle body with No.2 air tube assembly x Engine unit2525518
Engine front mounting x Engine front mounting bracket8789064
Engine front mounting x Transaxle6465047
Engine rear mounting x Engine rear mounting bracket981,00072
Engine rear mounting x Transaxle6465047
Starter x Starter wire1515311
Starter x Transaxle3940029
Transaxle case protector x Transaxle2525018
Clutch release cylinder x Clutch housing121209
Clutch line bracket x Transaxle Bolt A
(See page MX–4) Bolt B12
4.9120
509
43 in.·lbf
Engine left mounting x Bracket8789064
Engine left mounting Bracket x Transaxle5253038
Front wheel1031,05076
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Center exhaust pipe4849035
Engine rear mounting x Center member7374054
Engine rear mounting bracket x Body6465047
Engine rear mounting bracket x Engine rear mounting8789064
Engine front mounting x Center member5254038
Engine front mounting bracket x Transaxle6465047
Engine front mounting bracket x Engine front mounting8789064
Front transport hook x Center member3940029
Engine mounting center member x Body7374054
Transaxle case protector x Transaxle2525018
No.2 selecting bellcrank with selecting bellcrank support2020014
Shift and select lever shaft lock bolt4950036
Shift and select lever shaft assembly x Transmission case2020014
Transmission case cover x Transmission case2930022
Breather plug4950036
Output shaft lock nut1231,25090
Shift fork and shift head set bolt2424017
Rear bearing retainer x Transmission case4243031
Straight screw plug2525018
Straight screw plug (Reverse restrict pin)131309
Reverse idler gear shaft lock bolt2930022

SS061–28
– SERVICE SPECIFICATIONSSUPPLEMENTAL RESTRAINT SYSTEM
SS–15
SUPPLEMENTAL RESTRAINT SYSTEM
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Steering wheel x Steering main shaft7879058
Front passenger airbag assembly x Instrument panel reinforcement2121015
Seatback frame set bolt2525518
Front seat installation bolt3737527
Front seat belt lap outer ancher set bolt4243031
Curtain shield airbag (infrater) x Instrument panel reinforcement9.810087 in.·lbf
Curtain Shield Airbag (deployment section) x Body55144 in.·lbf
Side and curtain shield airbag sensor assembly x Body2121015
Front seat outer belt retractor Upper bolt
Lower bolt5.0
4251
43044 in.·lbf
31
Instrument panel x Reinfocement1818413
Seatback x Body2121415

SS0K4–02
SS–18
– SERVICE SPECIFICATIONSBODY
BODY
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
FRONT WIPER AND WASHER–––
Wiper arm x Wiper link2020515
INSTRUMENT PANEL–––
Curtain shield air bag x Body55144
Steering wheel set nut3435025
Passenger airbag assembly x Reinforcement1818513
FRONT SEAT–––
Front seat assembly x Body3737527
REAR SEAT (Sedan)–––
Seatback assembly x Body2121415
Side seatback x Body2121415
REAR SEAT (Except Sedan)–––
Side seatback x Body2121415
Seat cushion assembly x Body2121415
SEAT BELT–––
Front Seat Belt :
Shoulder anchor adjuster x Body4243031
Shoulder anchor x Body4243031

D06632AB
D06638
Q10165
Filler Plug
Oil Level
0 – 5 mm
Drain Plug
D06631
MX–6
– MANUAL TRANSAXLE (E251)MANUAL TRANSAXLE UNIT
13. REMOVE ENGINE LEFT MOUNTING BRACKET 3 SET
BOLTS AND NUT
Torque:
Bolt A: 52 N·m (530 kgf·cm, 38 ft·lbf)
Nut B: 87 N·m (890 kgf·cm, 64 ft·lbf)
14. REMOVE ENGINE LEFT MOUNTING BRACKET
Lower the transaxle side and remove the bolt and bracket.
Torque: 52 N·m (530 kgf·cm, 38 ft·lbf)
15. REMOVE FRONT WHEEL
Torque: 216 N·m (2,200 kgf·cm, 159 ft·lbf)
16. RAISE VEHICLE
NOTICE:
Make sure that the vehicle is securely supported.
17. DRAIN TRANSAXLE OIL
Oil grade: API GL–4 or GL–5
Viscosity: SAE 75W–90
Capacity: 3.9 liters (4.1 US qts, 3.4 Imp. qts)
Torque: 49 N·m (500 kgf·cm, 36 ft·lbf)
18. REMOVE FRONT EXHAUST PIPE
(a) Remove the 2 bolts, 2 nuts and gasket from the exhaust
manifold.
Torque: 62 N·m (630 kgf·cm, 46 ft·lbf)
(b) Remove the 2 bolts, 2 springs, gasket and pipe.
Torque: 48 N·m (490 kgf·cm, 35 ft·lbf)
19. REMOVE LH AND RH FRONT DRIVE SHAFTS
(See page SA–1)
20. REMOVE ENGINE MOUNTING CENTER MEMBER
(a) Remove the 2 bolts and front transport hook.
Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
(b) Support the suspension crossmember with a jack.
(c) Remove the nuts, and disconnect the suction pipe.

SA02Z–03
SA–10
– SUSPENSION AND AXLEFRONT DRIVE SHAFT
INSTALLATION
1. LH drive shaft:
INSTALL DRIVE SHAFT TO TRANSAXLE
(a) Install a new snap ring to the inboard joint shaft.
(b) Coat the gear oil to the inboard joint shaft and differential case sliding surface.
(c) Set the snap ring with opening side facing downward.
(d) Using a brass bar and hammer, install the drive shaft.
NOTICE:
Be careful not to damage the dust cover of the drive shaft and oil seal lip of the transaxle.
HINT:
Whether the inboard joint shaft is in contact with the pinion shaft or not can be known from the sound or feel-
ing when driving it in.
(e) Check that there is 2 – 3 mm (0.08 – 0.12 in.) of play in the axial direction.
(f) Check that the drive shaft cannot be removed by hand.
2. RH drive shaft:
INSTALL DRIVE SHAFT TO TRANSAXLE
(a) Coat the gear oil to the inboard joint shaft and differential case sliding surface.
(b) Install the drive shaft with the center bearing bracket.
NOTICE:
Be careful not to damage the dust cover of the drive shaft and oil seal lip of the transaxle.
(c) Install the 2 bolts.
Torque: 64 N·m (650 kgf·cm, 47 ft·lbf)
3. CONNECT DRIVE SHAFT TO AXLE HUB
NOTICE:
Be careful not to damage the boot and ABS speed sensor rotor.
4. CONNECT LOWER SUSPENSION ARM TO LOWER BALL JOINT
Torque: 127 N·m (1,300 kgf·cm, 94 ft·lbf)
5. CONNECT TIE ROD END TO STEERING KNUCKLE
(a) Connect the tie rod end to the steering knuckle.
(b) Install the nut and a new cotter pin.
If the holes for the cotter pin are not aligned, tighten the nut further up to 60.
Torque: 49 N·m (500 kgf·cm, 36 ft·lbf)
6. INSTALL DRIVE SHAFT LOCK NUT
(a) While applying brakes, install the nut.
Torque: 216 N·m (2,200 kgf·cm, 159 ft·lbf)
(b) Install the lock cap and a new cotter pin.
If the holes for the cotter pin are not aligned, tighten the nut further up to 60.
7. w/ABS:
INSTALL ABS SPEED SENSOR AND BOLT
Torque: 8.0 N·m (82 kgf·cm, 71 in.·lbf)
8. FILL AND CHECK GEAR OIL (See page MX–4)
9. INSTALL FRONT WHEEL
Torque: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
10. CHECK FRONT WHEEL ALIGNMENT (See Pub. No. RM599E on page SA–4)
11. CHECK ABS SPEED SENSOR SIGNAL (See Pub. No. RM599E on page DI–115)

H11621
Instrument Panel
Column CoverNo.1 Register
Steering Wheel Combination Meter
Steering Wheel PadHeater Control Assembly
Cluster Finish Panel
Glove Compartment DoorFront Ash Receptacle
Lower Finish Panel
Rear Console Box No.1 Under Cover
Shift Knob
Parking Brake Hole Cover Combination Switch
Center Cluster Finish Panel
78 (790, 58)
N·m (kgf·cm, ft·lbf) : Specified torque
Cowl Side Panel
18 (184, 13)
Cover
Cover
– SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
RS–21