1999 TOYOTA AVENSIS airbag off




 

B00972
ONTurn ignition switch ON. INSPECTION PROCEDURE
2 Check voltage at IG2 and ACC of airbag sensor assembly.
OK:
Voltage: Below 16V
Connector being checked is connected.  Indicates the condition of the connector of ECU during the check.PREPARATION:
CHECK:
Check battery and charging system.
(See charging system section)
OKNG
 Indicates the position of the ignition switch during the check.
Check from the connector back side.
(with harness)
Ignition Switch LOCK (OFF)
Ignition Switch START
LOCKIgnition Switch ON
Ignition Switch ACC
STARTON
ACC
Inspection Procedure
Use the inspection procedure to determine
if the circuit is normal or abnormal, and if it
is abnormal, use it to determine whether the
problem is located in the sensors, actuators,
wire harness or ECU.
 Indicates the place to check the voltage or resistance.
 Indicates the connector position to be checked, from the front or back side.
Connector being checked is disconnected. Check from the connector front side. (without harness)
In this case, care must be taken not to bend the terminals.
E6 Connector KNKWire Harness
E6 Connector KNK
Measure voltage between terminals IG2 and ACC of
airbag sensor assembly and body ground.
Airbag Sensor Assembly
(+)
(–)ACC IG2
 IN–28
– INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS

RS0IK–01
H03384
H11628
H03386
H03387
H03388
RS–2
– SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
OPERATION
1. SIDE AIRBAG ASSEMBLY
The inflater and bag of the SRS side airbag are stored in the
side airbag assembly and cannot be disassembled. The inflater
contains a squib, igniter charge and gas generant, etc., and in-
flates the bag when instructed by the side airbag sensor assem-
bly.
2. CURTAIN SHIELD AIRBAG ASSEMBLY
The inflater and bag of the SRS curtain shield airbag are stored
in the curtain shield airbag assembly and cannot be disas-
sembled. The inflater contains a squib, igniter charge and gas
generant, etc., and inflates the bag when instructed by the side
airbag sensor assembly.
3. SRS WARNING LIGHT
The SRS warning light is located on the combination meter. It
goes on to alert the driver of trouble in the system when a mal-
function is detected in the airbag sensor assembly. In normal
operation conditions when the ignition switch is turned to the
ACC or ON position, the light goes on for about 6 seconds and
then goes off.
4. AIRBAG SENSOR ASSEMBLY
The airbag sensor assembly is mounted on the floor inside the
lower center finish panel. The airbag sensor assembly consists
of an airbag sensor, safing sensor, diagnosis circuit ignition
control and drive circuit, etc. It receives signals from the airbag
sensor, front airbag sensor, side airbag sensor and judges
whether the SRS must be activated or not.
5. SIDE AND CURTAIN SHIELD AIRBAG SENSOR AS-
SEMBLY
The side and curtain shield airbag sensor assembly is mounted
in the LH and RH center pillars. The side airbag sensor assem-
bly consists of a side airbag, sensor, safing sensor and diagno-
sis circuit, etc. It sends signals to the airbag sensor assembly
to judges whether the SRS side airbag must be activated or not.

No.
AGround (Power)
Tacho Pick–UP Sensor
EFI ECU (3S–FE, 2C–TE Engine)
EGR (2C–T Engine)
Vehicle Speed Sensor
EFI ECU
Water Temperature Sender Gauge (2C–T Engine)
Ground (Engine)
Ground
Outside Temperature Sender Gauge
Ground (Fuel)
Fuel Sender Gauge
Ground (Power)
Ground (Speed)
Turn Signal Switch (Right)
Other Parts
Oil Level Warning Switch
O/D OFF Switch
ECT ECU (Gasoline Engine)
Fuel Filter Warning Switch (Diesel Engine)
Glow Plug Timer (Diesel Engine)
EFI ECU (Gasoline Engine)
ECT Pattern Select Switch
ABS ECU
Rear Fog Light Switch 1
3
5
6
7
8
9
10
11
12
14
15
17
18
19
21
22
23
24
25
26Wire Harness Side
1
2
3
4
5
6
7
9
11
13
14
15
16
17
18
19
20
22
24
26Turn Signal Switch (Left)
H–LP Fuse
Front Fog Light Switch
Alternator L Terminal
Brake Fluid Level Warning Switch
Parking Brake Switch
ECU+B Fuse
Taillight Relay
GAUGE Fuse
Ground (Signal)
DOOR Fuse
EFI ECU (Gasoline Engine)
EGR ECU (Diesel Engine)
Headlight Dimmer Switch
Low Oil Pressure Warning Switch
IGN Fuse
Door Courtesy Switch
Airbag ECU
Taillight Relay
GAUGE Fuse
Ground (Signal)
DOOR Fuse
B
– BODY ELECTRICALCOMBINATION METER
BE–5

BO2J0–01
H03507
: Clip
H11626
Pillar Garniush
Cover
2 Clips
I12491
H03502
BO–4
– BODYWINDSHIELD
REMOVAL
1. REMOVE THESE PARS
(a) Remove the front wiper arms.
(b) Remove the weatherstrip.
(c) Remove the cowl louver.
(d) Remove the sun visors and holders.
(e) Remove the map light assembly.
(f) Remove the assist grip.
(g) Remove the upper part of front door opening trims.
(h) w/ Curtain Shield Airbag:
(1) Using a screwdriver, raise the pillar garnish cover.
(2) Remove the bolt, pillar garnish cover and front pillar
garnish.
(3) Remove the 2 bolts.
(4) Pack the airbag with protection cover.
NOTICE:
Protection range is from instrument panel to ceiling.
(i) Remove the front pillar garnishes.
(j) Remove the inner rear view mirror.
(k) Remove the upper back panel hole No.1 cover.
2. REMOVE WINDSHIELD OUTSIDE UPPER MOULDING
Using a knife, cut off the moulding, as shown.
NOTICE:
Do not damage the body with the knife.