1999 TOYOTA AVENSIS lock

I04818
SPEEDOMETER
TACHOMETER
WATER TEMP.
FUEL
OIL LEVEL
ODO / TRIP
METER
OUTSIDE TEMP.
CLOCK
RHEOSTATLCD
DISPLAY
LCD
DISPLAY S
T
W
FA18
B7
B20 A5
A15
A3
A6
A7
A8
A12
A11
A19
A10
A9
B11
B24
B5
A22
B4
A23
B14
A23
A25
B16
B14
B21
A22
A14VOLTAGE
STABILIZER
B17
B22
B9
B26
A24 Brake Warning
Fuel filter Warning
Discharge Waring
Economy Indicator
Turbo / Glow Plug Indicator
Glow Plug Indicator
ABS Warning
Low Oil Pressure Warning
Check Engine Warning
O / D OFF Indicator
ECT SNOW Indicator
ECT PWR Indicator
Rear Fog Light Indicator
High Beam Indicator
Right Turn Indicator
Left Turn Indicator
Open Door Warning
SRS Warning
Front Fog light Indicator A1
B15
B18A26
B2
A17
B1
B13
B6
B3 B19
BE–4
– BODY ELECTRICALCOMBINATION METER

BO5232
BO1689
– BODYWINDSHIELD
BO–5
3. REMOVE WINDSHIELD GLASS
(a) Push piano wire through between the body and glass
from the interior.
(b) Tie both wire ends to a wooden block or similar object.
HINT:
Apply adhesive tape to the outer surface to keep the surface
from being scratched.
NOTICE:
When separating the glass, take care not to damage the
paint and exterior ornaments. To prevent scratching the
safety pad when removing the windshield, place a plastic
sheet between the piano wire and safety pad.
(c) Cut the adhesive by pulling the piano wire around it.
(d) Remove the glass.
NOTICE:
Leave as much of the adhesive on the body as possible
when cutting off the glass.

BO2J3–01
I12491
H03659
H03660
: 4 Clips BO–16
– BODYINSTRUMENT PANEL
REMOVAL
1. REMOVE THESE PARTS:
(a) Remove the front door opening trims.
(b) Remove the front pillar garnishes.
(c) w/ Curtain Shield Airbag:
(1) Remove the 2 bolts.
(2) Pack the airbag with protection cover.
(3) Using a screwdriver, raise the pillar garnish cover.
(4) Remove the bolt, pillar garnish cover and front pillar
garnish.
NOTICE:
Protection rang is from instrument panel to ceiling.
(d) Remove the front door scuff plates.
(e) Remove the cowl side trims.
(f) Remove the rear door opening trims.
(g) Remove the rear door scuff plates.
(h) Remove the center pillar lower covers.
(i) Remove the front seats.
2. REMOVE STEERING WHEEL
(See Pub. No.RM599E on page SR–13)
3. REMOVE LOWER FINISH PANEL
(a) Remove the 2 screws and hood lock control lever.
(b) Remove the 2 screws and lower finish panel.
4. REMOVE THESE PARTS:
(See Pub. No.RM599E on page SR–13)
(a) Remove the column cover.
(b) Remove the combination switch.
(c) Remove the steering column.
5. REMOVE CLUSTER FINISH PANEL
(a) Remove the 2 screws.
(b) Using a screwdriver, remove the cluster finish panel, then
disconnect the connector.
HINT:
Tape the screwdriver tip before use.
6. REMOVE COMBINATION METER

H03662
: 3 Clips
H03661
: 3 Clips
H03660
: 3 Clips
H03659
BO–20
– BODYINSTRUMENT PANEL
8. INSTALL NO.1 UNDER COVER
Install the No.1 under cover.
9. INSTALL NO.1 REGISTER
Install the No.1 register.
10. INSTALL COMBINATION METER
11. INSTALL CLUSTER FINISH PANEL
(a) Install the cluster finish panel, then connect the connec-
tor.
(b) Install the 2 screws.
12. INSTALL THESE PARTS:
(See Pub. No. RM 599E, page SR–13)
(a) Install the steering column.
(b) Install the combination switch.
(c) Install the column cover.
13. INSTALL LOWER FINISH PANEL
(a) Install the lower finish panel with the 2 screws.
(b) Install the hood lock control lever.
14. INSTALL STEERING WHEEL
(See Pub. No. RM 599E, page SR–13)
15. INSTALL THESE PARTS:
(a) Install the front seats.
Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
(b) Install the center pillar lower covers.
(c) Install the rear door scuff plates.
(d) Install the rear door opening trims.
(e) Install the cowl side trims.
(f) Install the front door scuff plates.

AC2A5–01
I02286
Drive Belt
Adjusting Bolt
Idle Pulley Lock Nut AC–2
– AIR CONDITIONINGDRIVE BELT (1CD–FTV)
REMOVAL
REMOVE DRIVE BELT
(a) Loosen the idle pulley lock nut.
(b) Loosen the drive belt tension by adjusting bolt and re-
move the drive belt.

AC2A6–01
I02286
Drive Belt
Adjusting Bolt
Idle Pulley Lock Nut
– AIR CONDITIONINGDRIVE BELT (1CD–FTV)
AC–3
INSTALLATION
INSTALL DRIVE BELT
(a) Tighten the idle pulley lock nut temporarily.
Torque: 2.5 N·m (25 kgf·cm, 22 in.·lbf)
(b) Install the drive belt.
(c) Using a adjusting bolt, adjust drive belt tension.
Drive belt tension:
New belt: 520 – 755 N (53 – 77 kgf)
Used belt: 196 – 392 N (20 – 40 kgf)
(d) Tighten the idle pulley lock nut at regular torque.
Torque: 39 N·m (390 kgf·cm, 29 ft·lbf)

I12471
A
B
: Low Pressure Charging Hose
: High Pressure Charging HoseA
B
AC2A7–02
N04392
Sleeve AC–4
– AIR CONDITIONINGMANIFOLD GAUGE SET (1CD–FTV)
MANIFOLD GAUGE SET
(1CD–FTV)
SET ON
1. CONNECT CHARGE HOSE TO MANIFOLD GAUGE
SET
Tighten the nuts by hand.
CAUTION:
Do not connect the wrong hoses.
2. CONNECT QUICK DISCONNECT ADAPTERS TO
CHARGING HOSES
Tighten the nuts by hand.
3. CLOSE BOTH HAND VALVES OF MANIFOLD GAUGE
SET
4. REMOVE CAPS FROM SERVICE VALVE ON REFRIG-
ERANT LINE
5. CONNECT QUICK DISCONNECT ADAPTER TO SER-
VICE VALVES
HINT:
Push the quick disconnect adapter onto the service valve, slide,
then slide the sleeve of the quick disconnect adapter downward
to lock it.

AC2A8–01
N06553
– AIR CONDITIONINGMANIFOLD GAUGE SET (1CD–FTV)
AC–5
SET OFF
1. CLOSE BOTH HAND VALVES OF MANIFOLD GAUGE
SET
2. DISCONNECT QUICK DISCONNECT ADAPTERS
FROM SERVICE VALVES ON REFRIGERANT LINE
HINT:
Slide the sleeve of the quick disconnect adapter upward to un-
lock the adapter and remove it from the service valve.
3. INSTALL CAPS TO SERVICE VALVES ON REFRIGER-
ANT LINE