1999 TOYOTA AVENSIS lock

H01583
Outer
Outer
– SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
RS–7
8. CONNECTION OF SIDE AND CURTAIN SHIELD AIR-
BAG SENSOR CONNECTOR
(a) Align the male connector (of the side of sensor) and fe-
male connector in the same direction as shown in the il-
lustration and fit in them without rubbing.
(b) As they are fitted in, the outer slides rearward. Press it un-
til the outer returns to its original position again.
If fitting stops half way, connectors will separate.
(c) Make sure to insert until they are locked. After fitting in,
pull them slightly to check that they are locked. (When
locked, make sure that the outer returns to its original
position and sound at the time of fitting in can be heard.)
HINT:

Do not fit in while holding the outer.

When fitting in, the outer slides. Do not touch it.

H01584
Slider
Disconnection is completed Slider
H01585
SliderSlider
RS–8
– SUPPLEMENTAL RESTRAINT SYSTEMSRS AIRBAG
9. DISCONNECTION OF SIDE AIRBAG AND CURTAIN
SHIELD AIRBAG CONNECTOR
(a) Place a finger on the slider.
(b) Slide the slider to release lock.
(c) Disconnect the connector.
10. CONNECTION OF SIDE AIRBAG AND CURTAIN
SHIELD AIRBAG CONNECTOR
(a) Align a lock part of male connector and a slider of female
connector in the same direction as shown in the illustra-
tion, fit in them without rubbing.
(b) Make sure to insert until they are locked. After fitting in pull
them slightly to check that they are locked. (When locked,
make sure that the outer returns to its original position and
sound at the time of fitting in can be heard.)
HINT:

As the slider slides, do not touch it.

Be careful not to deform the release board. If the release
board is deformed, replace it with a new one.

AB0158
Battery
SST
H04668
H04669
Battery
SST
R13455
10 m (33 ft) or more
H04540
– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY
RS–13
1. AIRBAG DEPLOYMENT WHEN SCRAPPING VE-
HICLE
HINT:
Have a battery ready as the power source to deploy the airbag.
(a) Check functioning of the SST. (See Pub. No. RM599E on
page RS–17)
SST 09082–00700
(b) Disconnect the side airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(c) Install the SST.
(1) Connect the 2 SST connector to the airbag connec-
tor.
SST 09082–00700, 09082–00750
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock.
(2) Move the SST at least 10 m (33 ft) away from the
front of the vehicle.
(3) Close all the doors and windows of the vehicle.
NOTICE:
Take care not to damage the SST wire harness.
(4) Connect the SST red clip to the battery positive (+)
terminal and the black clip to the battery negative
(–) terminal.
(d) Deploy the airbag.
(1) Check that no one is inside the vehicle or within 10
m (33 ft) area around the vehicle.
(2) Press the SST activation switch and deploy the air-
bag.
HINT:
The airbag deploys simultaneously as the LED of SST activa-
tion switch lights up.

H03412
H03413
RS–14
– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY
(e) Dispose of the side airbag assembly.
CAUTION:

The side airbag assembly is very hot when the airbag
is deployed, so leave it alone for at least 30 minutes
after deployment.

Use gloves and safety glasses when handling a side
airbag assembly with the deployed airbag.

Do not apply water, etc. to a side airbag assembly with
the deployed airbag.

Always wash your hands with water after completing
the operation.
When scrapping a vehicle, deploy the airbag and scrap
the vehicle with the side airbag assembly still installed.
2. DEPLOYMENT WHEN DISPOSING OF SIDE AIRBAG
ASSEMBLY
NOTICE:

When disposing of the side airbag assembly only,
never use the customer’s vehicle to deploy the air-
bag.

Be sure to follow the procedure given below when de-
ploying the airbag.
HINT:
Have a battery ready as the power source to deploy the airbag.
(a) Remove the seatback frame. (See page RS–10)
(b) Remove the side airbag assembly from the seatback
frame.
(1) Remove the 2 nuts, wire and side airbag assembly.
CAUTION:

Never disassemble the side airbag assembly.

Store the side airbag assembly with the airbag de-
ployment side facing upward.
(2) Release the lock of connector, then disconnect the
connector of side airbag sub wire harness.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness

AB0158
SSTBattery
H03420
Tires
(5 or More)
R05403
H0342110 m (33 ft) or more SSTBattery
Side Airbag
Assembly
RS–16
– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY

Always tie down the side airbag assembly with the
airbag door facing inside.
NOTICE:
The tire will be marked by the airbag deployment, so use
the redundant tire.
(d) Check functioning of the SST.
SST 09082–00700, 09082–00750
(e) Place the tires.
(1) Place at least 2 tires under the tire to which the side
airbag assembly is tied.
(2) Place at least 2 tires over the tire to which the side
airbag assembly is tied. The top tire should have the
wheel installed.
(3) Tie the tires together with 2 wire harnesses.
CAUTION:
Make sure that the wire harnesses are tight. It is very dan-
gerous when loose wire harnesses results in the tires com-
ing free due to the shock from the airbag deploying.
HINT:
Place the SST connector and wire harness inside tires. Secure
at least 1 m (3 ft) of slack for the wire harness.
(f) Install the SST.
Connect the connector of 2 SST to the side airbag assem-
bly connector.
SST 09082–00700, 09082–00750
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock.
(g) Deploy the airbag.

H11623
Curtain Shield
Airbag Connector
H11624
Battery
SST
SST
R13455
10 m (33 ft) or more
H11618
– SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
RS–27
(c) Disconnect the curtain shield airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(d) Install the SST.
(1) Connect the 2 SST connector to the airbag connec-
tor.
SST 09082–00700, 09082–00750
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock.
(2) Move the SST at least 10 m (33 ft) away from the
front of the vehicle.
(3) Close all the doors and windows of the vehicle.
NOTICE:
Take care not to damage the SST wire harness.
(4) Connect the SST red clip to the battery positive (+)
terminal and the black clip to the battery negative
(–) terminal.
(e) Deploy the airbag.
(1) Check that no one is inside the vehicle or within 10
m (33 ft) area around the vehicle.
(2) Press the SST activation switch and deploy the air-
bag.
HINT:
The airbag deploys simultaneously as the LED of SST activa-
tion switch lights up.
(f) Dispose of the curtain shield airbag assembly.
CAUTION:

The curtain shield airbag assembly is very hot when
the airbag is deployed, so leave it alone for at least 30
minutes after deployment.

Use gloves and safety glasses when handling a cur-
tain shield airbag assembly with the deployed airbag.

Do not apply water etc. to a curtain shield airbag as-
sembly with the deployed airbag.

H11609
10 m (33 ft)
or more SSTBattery
Curtain Shield Airbag Assembly
H11610
Vinyl Bag
RS–30
– SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
(e) Install the SST.
Connect the connector of 2 SST to the curtain shield air-
bag connector.
SST 09082–00700, 09082–00750
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock.
(f) Explode the airbag.
(1) Connect the SST red clip to the battery positive (+)
terminal and the black clip to the battery negative
(–) terminal.
(2) Check that no one is within 10 m (33 ft) area around
the tire which the curtain shield airbag is tied to.
(3) Press the SST activation switch and explode the
airbag.
HINT:
The airbag explodes simultaneously as the LED of the SST ac-
tivation switch lights up.
(g) Dispose of the curtain shield airbag.
CAUTION:

The curtain shield airbag is very hot when the airbag
is exploded, so leave it alone for at least 30 minutes
after explosion.

Use gloves and safety glasses when handling a cur-
tain shield airbag with the exploded airbag.

Do not apply water etc. to a curtain shield airbag with
the exploded airbag.

Always wash your hands with water after completing
the operation.
(1) Remove the curtain shield airbag from the tire.
(2) Place the curtain shield airbag in a vinyl bag, tie the
end tightly and dispose of it in the same way as oth-
er general parts disposal.

RS0IW–01
H11615
(5)(7)
(4)
(6)
(1)(2)(3)
H11613
(1)(2)(3)(4)
(5)
RS–32
– SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
INSTALLATION
NOTICE:

Never use airbag parts from another vehicle. When
replacing parts, replace them with new parts.

Make sure that the curtain shield airbag assembly is
installed with the specified torque.

If the curtain shield airbag assembly has been
dropped, or there are cracks, dents or other defects
in the case or connector, replace the curtain shield
airbag assembly with a new one.

When installing the curtain shield airbag assembly,
take care it is not pinched between other parts.
1. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY
(a) Connect the connector of the curtain shield airbag sub
wire harness then lock it.
(b) In order shown in the illustration, install the curtain shield
airbag with the bolts and grommets.
Torque:
Nuts: 9.8 N·m (100 kgf·cm, 87 in.·lbf)
Bolts: 5 N·m (51 kgf·cm, 44 in.·lbf)
CAUTION:
Pay attention for not causing twisting.
(c) Install the instrument panel assembly. (See page
BO–19)
2. INSTALL CURTAIN SHIELD AIRBAG
(IN CASE WITHOUT INSTALLING INFLATER)
In order shown in the illustration, install the deployment section
of the curtain shield airbag with the bolts and grommet.
Torque: 5 N·m (51 kgf·cm, 44 in.·lbf)
CAUTION:
Pay attention for not causing twisting.
3. INSTALL ROOF HEADLINING

Sedan model (See page BO–25)

Liftback model (See page BO–30)

Wagon model (See page BO–36)