1999 SUBARU LEGACY key

3. Cylinder Head and Valve Assembly
B2M1955A
(1) Exhaust valve
(2) Intake valve
(3) Intake valve guide
(4) Intake valve spring seat(5) Intake valve oil seal
(6) Valve spring
(7) Retainer
(8) Retainer key(9) Exhaust valve guide
(10) Exhaust valve spring seat
(11) Exhaust valve oil seal
8
2-3a[C300]COMPONENT PARTS
3. Cylinder Head and Valve Assembly

5. Crankshaft and Piston
B2M1958A
(1) Flywheel (MT)
(2) Bell bearing (MT)
(3) Reinforcement (AT)
(4) Drive plate (AT)
(5) Top ring
(6) Second ring
(7) Oil ring
(8) Piston(9) Piston pin
(10) Circlip
(11) Connecting rod bolt
(12) Connecting rod
(13) Connecting rod bearing
(14) Connecting rod cap
(15) Crankshaft
(16) Woodruff key(17) Crankshaft bearing #1, #3
(18) Crankshaft bearing #2, #4
(19) Crankshaft bearing #5
Tightening torque: N´m (kg-m, ft-lb)
T1:
44±2 (4.5±0.2, 32.5±1.4)
T2:72±3 (7.3±0.3, 52.8±2.2)
10
2-3a[C500]COMPONENT PARTS
5. Crankshaft and Piston

IPress-in the push adjuster rod gradually tak-
ing more than three minutes.
IDo not allow press pressure to exceed 9,807
N (1,000 kg, 2,205 lb).
IPress the adjuster rod as far as the end sur-
face of the cylinder. Do not press the adjuster
rod into the cylinder. Doing so may damage the
cylinder.
4) Measure the extension of rod beyond the body.
If it is not within specifications, replace with a new
one.
Rod extension: H
5.7
±0.5 mm (0.224±0.020 in)
H2M2381A
3. BELT TENSION PULLEY
1) Check mating surfaces of timing belt and con-
tact point of adjuster rod for abnormal wear or
scratches. Replace automatic belt tension adjuster
assembly if faulty.
2) Check tension pulley for smooth rotation.
Replace if noise or excessive play is noted.
3) Check tension pulley for grease leakage.
4. BELT IDLER
1) Check belt idler for smooth rotation. Replace if
noise or excessive play is noted.
2) Check belt outer contacting surfaces of idler
pulley for abnormal wear and scratches.
3) Check belt idler for grease leakage.
5. CAMSHAFT AND CRANKSHAFT
SPROCKET
1) Check sprocket teeth for abnormal wear and
scratches.
2) Make sure there is no free play between
sprocket and key.
3) Check crankshaft sprocket notch for sensor for
damage and contamination of foreign matter.
C: INSTALLATION
1. CAMSHAFT AND CRANKSHAFT SPROCKET
B2M2598A
(1) Tensioner bracket
(2) Belt cover No. 2 (RH)
(3) Belt cover No. 2 (LH)
(4) Crankshaft sprocket(5) Camshaft sprocket No. 1
(6) Camshaft sprocket No. 2Tightening torque: N´m (kg-m, ft-lb)
T1:
5±1 (0.5±0.1, 3.6±0.7)
T2:25±3 (2.5±0.3, 18.1±2.2)
T3:78±5 (8.0±0.5, 57.9±3.6)
19
[W2C1]2-3aSERVICE PROCEDURE
2. Timing Belt

B: DISASSEMBLY
B2M2629A
(1) Valve rocker ASSY
(2) Camshaft cap
(3) Camshaft
(4) Oil seal
(5) Plug(6) Spark plug pipe gasket
(7) Retainer key
(8) Retainer
(9) Valve spring
(10) Oil seal(11) Valve spring seat
(12) Valve guide
(13) Valve
1) Remove valve rocker assembly, camshaft cap
and camshaft.
2) Remove oil seal.
3) Remove plug.
4) Place cylinder head on ST.
ST 498267800 CYLINDER HEAD TABLE5) Set ST on valve spring. Compress valve spring
and remove the valve spring retainer key. Remove
each valve and valve spring.
ST 499718000 VALVE SPRING REMOVER
CAUTION:
IMark each valve to prevent confusion.
IUse extreme care not to damage the lips of
the intake valve oil seals and exhaust valve oil
seals.
B2M2630A
42
2-3a[W5B0]SERVICE PROCEDURE
5. Cylinder Head

D: ASSEMBLY
B2M2629B
(1) Valve
(2) Valve guide
(3) Valve spirng seat
(4) Oil seal
(5) Valve spring(6) Retainer
(7) Retainer key
(8) Spark plug gasket
(9) Camshaft
(10) Oil seal(11) Plug
(12) Camshaft cap
(13) Valve rocker ASSY
1) Installation of valve spring and valve
(1) Place cylinder head on ST.
ST 498267400 CYLINDER HEAD TABLE
(2) Coat stem of each valve with engine oil and
insert valve into valve guide.
CAUTION:
When inserting valve into valve guide, use spe-
cial care not to damage the oil seal lip.
(3) Install valve spring and retainer.
CAUTION:
Be sure to install the valve springs with their
close-coiled end facing the seat on the cylinder
head.(4) Set ST on valve spring.
ST 499718000 VALVE SPRING REMOVER
B2M2630A
48
2-3a[W5D0]SERVICE PROCEDURE
5. Cylinder Head

(5) Compress valve spring and fit valve spring
retainer key.
B2M2634A
(6) After installing, tap valve spring retainers
lightly with wooden hammer for better seating.
2) Install plug.
3) Install camshaft, camshaft cap and valve rocker
assembly.

4) Install plug using ST.
ST 499587100 OIL SEAL INSTALLER
5) Install oil seal using ST.
ST 499587500 OIL SEAL INSTALLER
E: INSTALLATION
1. CYLINDER HEAD
B2M2627B
(1) Cylinder head gasket
(2) Cylinder head(3) Cylinder head bolt
(4) Rocker cover
1) Install cylinder head and gaskets on cylinder
block.
CAUTION:
Use new cylinder head gaskets.
49
[W5E1]2-3aSERVICE PROCEDURE
5. Cylinder Head

3. Cylinder Head and Valve
Assembly
S2M0406A
(1) Exhaust valve
(2) Intake valve
(3) Cylinder head
(4) Valve spring seat(5) Intake valve oil seal
(6) Valve spring
(7) Retainer
(8) Retainer key(9) Valve lifter
(10) Shim
(11) Exhaust valve oil seal
10
2-3b[C300]COMPONENT PARTS
3. Cylinder Head and Valve Assembly

5. Crankshaft and Piston
B2M1958A
(1) Flywheel (MT vehicles only)
(2) Bell bearing (MT vehicles only)
(3) Reinforcement (AT vehicles only)
(4) Drive plate (AT vehicles only)
(5) Top ring
(6) Second ring
(7) Oil ring
(8) Piston(9) Piston pin
(10) Circlip
(11) Connecting rod bolt
(12) Connecting rod
(13) Connecting rod bearing
(14) Connecting rod cap
(15) Crankshaft
(16) Woodruff key(17) Crankshaft bearing #1, #3
(18) Crankshaft bearing #2, #4
(19) Crankshaft bearing #5
Tightening torque: N´m (kg-m, ft-lb)
T1:
44±2 (4.5±0.2, 32.5±1.4)
T2:72±3 (7.3±0.3, 52.8±2.2)
12
2-3b[C500]COMPONENT PARTS
5. Crankshaft and Piston