1999 SUBARU LEGACY clutch

4. OIL PUMP COVER
B3M0990A
(1) High clutch pressure
(2) Lock-up release pressure(3) Front lubricating hole
(4) Lock-up apply pressure(5) Reverse clutch pressure
5. OIL PUMP HOUSING
B3M0991A
(1) Oil pump outlet pressure
(2) Lock-up apply pressure
(3) Lock-up release pressure(4) High clutch pressure
(5) Drain
(6) Air breather(7) Reverse clutch pressure
13
[S1D5]3-2SPECIFICATIONS AND SERVICE DATA
1. Automatic Transmission and Differential

6. TRANSMISSION CASE
B3M0992A
(1) Oil pump inlet port
(2) Reverse clutch pressure
(3) Oil pump outlet port
(4) Lock-up apply pressure(5) Lock-up release pressure
(6) High clutch pressure
(7) Oil cooler outlet pressure
(8) Line pressure(9) Pilot pressure
(10) Low & reverse brake pressure
(11) Low clutch pressure
(12) 2-4 brake pressure
7. EXTENSION CASE
B3M0993A
14
3-2[S1D6]SPECIFICATIONS AND SERVICE DATA
1. Automatic Transmission and Differential

1. Torque Converter Clutch and Case
B3M0918A
(1) Pitching stopper bracket
(2) O-ring
(3) Differential oil level gauge
(4) Stay
(5) Seal pipe
(6) Seal ring
(7) Oil pump shaft
(8) Clip(9) Oil drain pipe
(10) Input shaft
(11) O-ring
(12) Torque converter clutch
(13) Drain plug
(14) Gasket
(15) Oil seal
(16) Torque converter clutch caseTightening torque: N´m (kg-m, ft-lb)
T1:
18±5 (1.8±0.5, 13.0±3.6)
T2:41±3 (4.2±0.3, 30.4±2.2)
T3:44±3 (4.5±0.3, 32.5±2.2)
15
[C100]3-2COMPONENT PARTS
1. Torque Converter Clutch and Case

(1) Oil level gauge
(2) Oil charger pipe
(3) O-ring
(4) Transfer valve plate
(5) Transfer valve ASSY
(6) Transfer clutch seal
(7) Duty solenoid C (Transfer)
(8) Straight pin
(9) Return spring
(10) Shaft
(11) Parking pawl
(12) Parking support
(13) Inlet filter
(14) Gasket
(15) Inlet pipe
(16) Union screw
(17) O-ring
(18) Test plug
(19) Oil filter(20) Oil filter stud bolt
(21) Drain plug
(22) Gasket
(23) Oil pan
(24) Magnet
(25) Stud bolt (Short)
(26) Stud bolt (Long)
(27) Parking rod
(28) Manual plate
(29) Spring pin
(30) Detention spring
(31) Ball
(32) Spring
(33) Gasket
(34) Outlet pipe
(35) Union screw
(36) Oil seal
(37) Select lever
(38) Inhibitor switch ASSY(39) Nipple
(40) Air breather hose
(41) Transmission case
(42) Plate ASSY
(43) Washer
Tightening torque: N´m (kg-m, ft-lb)
T1:
3.4±0.5 (0.35±0.05, 2.5±0.4)
T2:4.9±0.5 (0.50±0.05, 3.6±0.4)
T3:5.9±1.0 (0.60±0.10, 4.3±0.7)
T4:7.8±1.0 (0.80±0.10, 5.8±0.7)
T5:12.7±1.0 (1.30±0.10, 9.4±0.7)
T6:13.7±2.0 (1.4±0.2, 10.1±1.4)
T7:17.7±2.9 (1.80±0.30, 13.0±2.2)
T8:24.5±2.0 (2.50±0.20, 18.1±1.4)
T9:24.5±2.9 (2.5±0.3, 18.1±2.2)
T10:34.3±2.9 (3.50±0.30, 25.3±2.2)
19
[C300]3-2COMPONENT PARTS
3. Transmission Case and Control Device

4. Control Valve and Harness Routing
B3M0928A
(1) Stay
(2) Transmission harness
(3) O-ring
(4) O-ring
(5) Torque converter turbine speed
sensor
(6) O-ring
(7) Vehicle speed sensor 2 (Front)
(8) O-ring
(9) Vehicle speed sensor 1 (Rear)
(10) Upper valve body
(11) Accumulator piston(12) Accumulator spring
(13) Side plate
(14) Separate plate
(15) Middle valve body
(16) Separate plate
(17) Fluid filter
(18) Fluid filter
(19) Lower valve body
(20) Shift solenoid 2
(21) Shift solenoid 1
(22) 2-4 brake timing solenoid
(23) Duty solenoid D (2-4 brake)(24) ATF temperature sensor
(25) Duty solenoid A (Line pressure)
(26) Low clutch timing solenoid
(27) Duty solenoid B (Lock-up)
(28) Oil strainer
Tightening torque: N´m (kg-m, ft-lb)
T1:
7±1 (0.7±0.1, 5.1±0.7)
T2:8±1 (0.8±0.1, 5.8±0.7)
20
3-2[C400]COMPONENT PARTS
4. Control Valve and Harness Routing

5. High Clutch and Reverse Clutch
B3M1179A
(1) High clutch drum
(2) Lip seal
(3) Lathe cut seal ring
(4) Reverse clutch piston
(5) Lathe cut seal ring
(6) Lathe cut seal ring
(7) High clutch piston
(8) Spring retainer(9) Cover
(10) Snap ring
(11) Driven plate (Thicker)
(12) Driven plate (Thinner)
(13) Drive plate
(14) Retaining plate
(15) Snap ring
(16) Dish plate(17) Driven plate
(18) Drive plate
(19) Retaining plate
(20) Snap ring
(21) Thrust needle bearing
(22) High clutch hub
21
[C500]3-2COMPONENT PARTS
5. High Clutch and Reverse Clutch

7. Low Clutch and Low & Reverse Brake
B3M1017A
(1) Retaining plate
(2) Drive plate
(3) Driven plate
(4) Dish plate
(5) Snap ring
(6) Cover
(7) Spring retainer
(8) Lathe cut seal ring
(9) Low piston
(10) Lathe cut seal ring
(11) Low clutch drum(12) Needle bearing
(13) Snap ring
(14) One-way clutch
(15) Snap ring
(16) Thrust needle bearing
(17) Seal ring
(18) Needle bearing
(19) One-way clutch inner race
(20) Socket bolt
(21) Spring retainer
(22) Return spring(23) Snap ring
(24) Retaining plate
(25) Leaf spring
(26) Drive plate
(27) Driven plate
(28) Dish plate
(29) Low and reverse brake piston
Tightening torque: N´m (kg-m, ft-lb)
T:
25±2 (2.5±0.2, 18.1±1.4)
23
[C700]3-2COMPONENT PARTS
7. Low Clutch and Low & Reverse Brake

10. Transfer and Extension
B3M0881A
(1) Thrust needle bearing
(2) Needle bearing
(3) Snap ring
(4) Pressure plate
(5) Drive plate
(6) Driven plate
(7) Snap ring
(8) Transfer piston seal
(9) Return spring(10) Transfer clutch piston
(11) Rear drive shaft
(12) Ball bearing
(13) Seal ring
(14) Gasket
(15) Transfer clutch pipe
(16) Extension case
(17) Transmission hanger
(18) Oil seal(19) Dust seal
(20) Test plug
(21) O-ring
(22) Clip
Tightening torque: N´m (kg-m, ft-lb)
T1:
13±1 (1.3±0.1, 9.4±0.7)
T2:25±2 (2.5±0.2, 18.1±1.4)
26
3-2[C1000]COMPONENT PARTS
10. Transfer and Extension