1999 LAND ROVER DEFENDER cooling

COOLING SYSTEM
1
REPAIR COUPLING - COOLING FAN
Service repair no - 26.25.19
Remove
1.Remove battery cover.
2.Disconnect battery negative lead.
3.Remove 3 bolts and remove engine acoustic
cover.
4.Remove cooling fan cowl.
NOTE: Thread is RH.
5.Remove cooling fan usingLRT-12-093and
LRT-12-094.
Refit
6.Position cooling fan and tighten using
LRT-12-093andLRT-12-094.
7.Fit cooling fan cowl.
8.Fit engine acoustic cover.
9.Reconnect battery negative lead.
10.Fit battery cover.THERMOSTAT
Service repair no - 26.45.09
Remove
1.Drain cooling system.See Adjustment.
2.Remove cooling fan.See this Section.
3.Release 3 clips and disconnect coolant hoses
from thermostat.
4.Remove thermostat.
Refit
5.Position thermostat, connect hoses and secure
with clips.
6.Fit cooling fan.See this Section.
7.Fill cooling system.See Adjustment.
ProCarManuals.com

26COOLING SYSTEM
2
REPAIR PUMP - COOLANT
Service repair no - 26.50.01
Remove
1.Drain cooling system.See Adjustment.
2.Remove centrifuge.See ENGINE , Repair.
3.Release clip and hose from coolant pump cover.
4.Remove 5 bolts securing coolant pump cover.
5.Remove cover and coolant pump from housing
and discard’O’rings.Refit
6.Clean coolant pump housing and mating faces.
7.Fit new’O’rings to coolant pump and cover.
8.Fit coolant pump and cover and tighten bolts to9
Nm (7 lbf.ft).
9.Connect hose to pump cover and secure clip.
10.Refit centrifuge.See ENGINE , Repair.
11.Refill cooling system.See Adjustment.
ProCarManuals.com

COOLING SYSTEM
3
REPAIR RADIATOR
Service repair no - 26.40.01
Remove
1.Remove front grille.See CHASSIS AND
BODY, Repair.
2.Drain cooling system.See Adjustment.
3.Remove cooling fan.See this Section.
4.Remove 5 bolts and move bonnet platform
aside.
5.Release clip and disconnect bleed hose from
radiator.
6.Release clip and disconnect top hose from
radiator.
7.Release clip and disconnect fuel cooler hose
from radiator.
8.Release clip and disconnect coolant rail hose
from radiator.
ProCarManuals.com

26COOLING SYSTEM
4
REPAIR
9.Remove 4 bolts securing RH and LH radiator
mounting brackets to body and remove brackets.
10.Release clip and release air hose from
turbocharger inlet pipe.11.Release bottom hose from bracket on lower
cooling fan cowl.
12.Remove radiator assembly and collect lower
mounting spacers.
13.Remove 2 bolts and remove intercooler from
radiator. Collect 2 nuts from radiator side
brackets.
14.Remove 2 rubber mountings from intercooler.
15.Remove 2 screws and remove lower cooling fan
cowl from radiator.
16.Remove 2 rubber mountings from bottom of
radiator.
ProCarManuals.com

COOLING SYSTEM
5
REPAIR Refit
17.Fit rubber mountings to bottom of radiator.
18.Fit lower cooling fan cowl to radiator and secure
with screws.
19.Fit nuts to radiator side brackets.
20.Position intercooler to radiator and tighten bolts.
21.Fit rubber mountings to intercooler.
22.Position mounting spacers and fit radiator.
23.Fit bottom hose into bracket on lower cooling fan
cowl.
24.Position air hose to turbocharger pipe and
secure with clip.
25.Position LH and RH radiator mounting brackets
to body and radiator and tighten bolts.
26.Position coolant rail hose to radiator and secure
with clip.
27.Position fuel cooler hose to radiator and secure
with clip.
28.Position top hose to radiator and secure with
clip.
29.Position bleed hose to radiator and secure with
clip.
30.Position bonnet platform and tighten bolts.
31.Fit cooling fan.See this Section.
32.Fit front grille.See CHASSIS AND BODY,
Repair.
33.Fill cooling system.See Adjustment.
ProCarManuals.com

MANIFOLD AND EXHAUST SYSTEM
3
REPAIR EXHAUST - TAIL PIPE AND SILENCER
Service repair no - 30.10.22
Remove
1.Raise vehicle on ramp.
2.Remove 3 nuts securing silencer to tail pipe.
3.Release tail pipe from mounting and remove tail
pipe.
4.Collect silencer to tail pipe gasket.
Refit
5.Clean silencer and tail pipe mating faces.
6.Position tail pipe and secure on mounting
rubber.
7.Using a new gasket, align silencer to tail pipe.
8.Fit nuts to silencer and tighten to25 Nm (18
lbf.ft).GASKET - INLET MANIFOLD
Service repair no - 30.15.08
Remove
1.Remove battery cover.
2.Disconnect battery negative lead.
3.Remove 3 bolts and remove engine acoustic
cover.
4.Release retainers and remove cooling fan cowl.
5.Disconnect multiplug from manifold air pressure
sensor and release 4 glow plug leads.
6.Remove 4 bolts, release EGR valve from inlet
manifold and discard gasket.
ProCarManuals.com

MANIFOLD AND EXHAUST SYSTEM
5
REPAIR Refit
16.Clean inlet manifold and mating face.
17.Fit new gasket.
18.Fit inlet manifold, and working from the centre
outwards, tighten nuts and bolts to25 Nm (18
lbf.ft).
19.Position harness to sensors and connect
multiplugs.
20.Tighten harness clip bolts to camshaft carrier to
10 Nm (7 lbf.ft).
21.Clean dip stick tube and fit new’O’ring.
22.Fit dip stick tube and tighten bolt to10 Nm (7
lbf.ft).
23.Connect glow plug leads.
24.Fit alternator support bracket and tighten bolts to
45 Nm (33 lbf.ft).
25.Position fuel cooler. Apply Loctite 242 to bolts
and tighten to18 Nm (13 lbf.ft).
26.Fit new gasket, position EGR valve and tighten
bolts to9 Nm (7 lbf.ft).
27.Connect multiplug to MAP sensor.
28.Fit cooling fan cowl.
29.Fit engine acoustic cover.
30.Reconnect battery negative lead.
31.Fit battery cover.GASKET - EXHAUST MANIFOLD
Service repair no - 30.15.12
Remove
1.Remove turbocharger.See FUEL SYSTEM,
Repair.
2. Models with A/C:Remove auxiliary drive belt.
See ELECTRICAL, Repair.
3.Remove 4 bolts securing compressor and move
to one side.
All Models
NOTE: EU3 Model illustrated.
4.Remove and discard 2 Allen screws securing
EGR pipe to exhaust manifold.
5.Remove 10 nuts securing exhaust manifold to
cylinder head.
6.Remove exhaust manifold and gasket.
ProCarManuals.com

37MANUAL GEARBOX
8
REPAIR
12.Remove 13 screws securing tunnel cover.
13.Release and remove tunnel cover.
14.Remove cooling fan.See COOLING SYSTEM,
Repair.
15.Remove air filter.See FUEL SYSTEM, Repair.
16.Remove 2 upper bolts securing clutch housing to
engine.
17.Remove bolt securing shim to clutch housing.
18.Release gearbox breather pipes from clips on
heater hose.
19.Remove starter motor.See ELECTRICAL,
Repair.
20.Remove exhaust front pipe.See MANIFOLD
AND EXHAUST SYSTEM, Repair.
21.Drain gearbox oil.See Adjustment.
22.Drain transfer gearbox oil.See
MAINTENANCE ,
23.Remove 3 nuts securing intermediate silencer to
tail pipe.
24.Release silencer from mounting rubbers, remove
silencer and discard gasket.
25.Mark front and rear propeller shaft to transfer
gearbox flanges for reassembly purposes.
ProCarManuals.com