1999 LAND ROVER DEFENDER cooling

ENGINE
13
REPAIR 11.Before refitting the camshaft cover, the fuel
injector rockers must be adjusted.
12.RemoveLRT-12-058.
13.Rotate engine clockwise until No. 1 injector lobe
is at full lift.
14.Rotate rocker adjusting screw clockwise until the
injector plunger is felt to bottom out.
15.Rotate rocker adjusting screw anti-clockwise 1
complete turn to give the plunger the required
bump clearance and tighten rocker adjusting
screw locknut to16 Nm (12 lbf.ft).
CAUTION: Ensure screw does not turn as
locknut is tightened.
16.Carry out above procedure for the remaining 4
rockers.
17.After completion of rocker adjustment, slowly
rotate engine clockwise 2 complete turns by
hand to ensure that no injectors are bottoming
out on their plungers.
18.Fit camshaft cover gasket.See this Section.
19.Fit cooling fan.See COOLING SYSTEM,
Repair.GASKET - COVER - CAMSHAFT
Service repair no - 12.29.40
Remove
1.Remove battery cover.
2.Disconnect battery negative lead.
3.Remove 3 bolts and remove engine acoustic
cover.
4.Release clip and disconnect breather hose from
camshaft cover.
5.Remove 13 bolts, spacers and sealing washers
from camshaft cover.
6.Remove camshaft cover and gasket.
Refit
7.Clean camshaft cover and mating face.
8.Renew sealing washers and spacers as
necessary.
ProCarManuals.com

12ENGINE
14
REPAIR
9. Not EU3 model:-Apply two 3 mm diameter
beads of sealant, Part No.STC 5433 to areas’A’
shown on illustration.
CAUTION: Excessive use of sealant could
result in blockage of oil drain hole,
arrowed’B’in illustration.
10.Fit new gasket to camshaft cover. fit cover and
tighten bolts to10 Nm (7 lbf.ft).
11.Position breather hose and secure clip.
12.Fit engine acoustic cover.
13.Reconnect battery negative lead.
14.Fit battery cover.ENGINE AND ANCILLARIES
Service repair no - 12.41.01.99
Remove
1.Remove underbelly panel.See CHASSIS AND
BODY, Repair.
2.Drain engine oil.
3.Remove radiator.See COOLING SYSTEM,
Repair.
4.Remove turbocharger.See FUEL SYSTEM,
Repair.
5.Remove starter motor.See ELECTRICAL,
Repair.
6.Remove air filter.See FUEL SYSTEM, Repair.
7.Loosen clip screw and release air intake hose
from intake elbow.
8.Release clips and disconnect coolant hoses
from fuel cooler and coolant rail.
ProCarManuals.com

ENGINE
15
REPAIR
NOTE: Non EU3 model illustrated.
9.Disconnect fuel hoses, tank to fuel cooler and
connector block on cylinder head.
CAUTION: Plug the connections.
10.Disconnect fuel hose from fuel cooler and secure
to connector block on cylinder head. This to
prevent contamination of the fuel system.
11.Release servo vacuum pipe, remove 4 bolts and
remove fuel cooler.
12.Release servo vacuum pipe from engine rear
cover clips and vacuum pump.
NOTE: Non EU3 model illustrated.
13.Disconnect vacuum hose from EGR valve.
14.Release EGR vacuum hose from vacuum pipe.
15.Disconnect multiplug from condensor cooling
fan.
NOTE: Non EU3 model illustrated.
16.Disconnect multiplugs from EGR solenoid, inlet
manifold sensor and injector harness.
ProCarManuals.com

12ENGINE
18
REPAIR
35.Remove 2 bolts and remove acoustic cover from
rear of cylinder head.
36.FitLRT-12-138to suitable lifting chains and
connect to lifting eyes on engine.
37.Remove 2 nuts from RH and LH front engine
mountings.
38.Fit trolley jack to support gearbox.
39.With assistance raise chains and remove engine
from vehicle.Refit
40.With assistance, raise engine from bench and
position in vehicle.
41.With assistance, align engine to gearbox input
shaft.
42.Position 2 upper bolts securing gearbox housing
to engine and tighten to50 Nm (37 lbf.ft).
43.Lower engine onto mountings and tighten nuts to
85 Nm (63 lbf.ft).
44.RemoveLRT-12-138from engine.
45.Fit and tighten bolt securing engine closing panel
to gearbox.
46.Raise vehicle on ramp.
47.Fit bolts securing gearbox housing to engine and
tighten to50 Nm (37 lbf.ft).
48.Lower ramp.
49.Fit acoustic cover to rear of cylinder head and
tighten bolts.
50.Position coolant hose to engine oil cooler and
secure clip.
51.Position PAS pump and tighten bolts to25 Nm
(18 lbf.ft).
52.Position PAS pulley and tighten bolts to25 Nm
(18 lbf.ft).
53.Position A/C compressor and tighten bolts to25
Nm (18 lbf.ft).
54.Route engine harness beneath inlet manifold
and connect multiplugs to oil pressure switch,
A/C compressor, and ECT sensor.
55.Fit and tighten bolts securing engine harness to
camshaft carrier.
56.Connect multiplug to alternator.
57.Connect battery lead to alternator and tighten
nut.
58.Clean CKP sensor and mating face.
CAUTION: If originally fitted:- Fit spacer to
CKP sensor.
59.Using a new’O’ring, fit CKP sensor, tighten bolt
to10 Nm (7 lbf.ft).
60.Connect CKP sensor multiplug.
61.Connect multiplugs to EGR solenoid, inlet
manifold sensor, injector harness, fuel
temperature sensor and CKP sensor.
62.Connect glow plug leads.
63.Connect multiplug to condensor cooling fan.
64.Connect vacuum hose to EGR valve.
65.Connect EGR vacuum hose to vacuum pipe.
66.Position pipe to vacuum pump and secure pipe
to acoustic cover clips.
67.Position fuel cooler. Apply Loctite 242 to bolts
and tighten to18 Nm (13 lbf.ft).
68.Disconnect fuel hose from connector block and
connect to fuel cooler.
69.Connect fuel hoses to fuel cooler and connector
block on cylinder head.
ProCarManuals.com

ENGINE
19
REPAIR 70.Connect coolant hoses to fuel cooler and coolant
rail and secure clips.
71.Fit air intake hose to intake elbow and tighten
clip screw.
72.Fit starter motor.See ELECTRICAL, Repair.
73.Fit turbocharger.See FUEL SYSTEM, Repair.
74.Fit radiator.See COOLING SYSTEM, Repair.
75.Fit air filter.See FUEL SYSTEM, Repair.
76.Fill engine with oil.
77.Fit underbelly panel.See CHASSIS AND
BODY, Repair.MOUNTING - FRONT - LH
Service repair no - 12.45.01
Remove
1.Remove centrifuge assembly.See this
Section.
2.Remove 3 bolts, remove oil filter adaptor
housing and discard gasket.
3.Fit suitable lifting chains to support engine.
4.Remove 2 nuts securing engine mounting to
chassis.
5.Remove 4 bolts securing engine mounting
bracket to cylinder block.
6.Remove nut securing mounting to mounting
bracket.
7.Remove mounting and mounting bracket.
8.Remove mounting shield.
ProCarManuals.com

ENGINE
29
REPAIR VALVE - RELIEF - OIL PRESSURE
Service repair no - 12.60.56
Remove
1.Remove sump gasket.See this Section.
2.Remove and discard oil pressure relief valve
plug from oil pump housing.
3.Remove spring and valve.
Refit
4.Clean valve and spring.
5.Clean valve seating inside oil pump housing.
6.Lubricate valve and seating.
7.Fit valve and spring to pump.
8.Apply Loctite 243 sealant to threads of a new
plug.
9.Fit plug and tighten to23 Nm ( 17 lbf.ft).
10.Fit sump gasket.See this Section.
11.Check engine oil level, top-up if necessary.COOLER - ENGINE OIL
Service repair no - 12.60.68
Remove
1.Drain cooling system.See COOLING
SYSTEM, Adjustment.
2.Remove centrifuge assembly.See this
Section.
3.Remove clutch housing bolt and release coolant
pipe from rear of engine.
4.Release clip and coolant hose from oil cooler.
5.Disconnect oil pressure switch multiplug.
6.Remove oil filter element using a suitable strap
wrench.
7.Remove 3 bolts, remove oil filter adaptor and
discard gasket.
8.Remove 7 bolts, remove oil cooler and discard
gasket.
9.Remove oil pressure switch.
ProCarManuals.com

12ENGINE
30
REPAIR Refit
10.Clean oil cooler and mating faces.
11.Fit oil pressure switch and tighten to9Nm(7
lbf.ft).
12.Position oil cooler using a new gasket and
tighten bolts to25 Nm (18 lbf.ft).
13.Position oil filter adaptor, fit new gasket and
tighten bolts to25 Nm (18 lbf.ft).
14.Position oil filter element hand tight then a
further half turn.
15.Position coolant hose to oil cooler and secure
clip.
16.Position coolant pipe and tighten clutch housing
bolt to50 Nm (37 lbf.ft).
17.Connect oil pressure switch multiplug.
18.Fit centrifuge assembly.See this Section.
19.Refill cooling system.See COOLING SYSTEM,
Adjustment.
20.Top up engine oil.CENTRIFUGE ASSEMBLY
Service repair no - 12.60.90
Remove
1.Remove fixings and remove underbelly panel.
See CHASSIS AND BODY, Repair.
2.Remove 2 bolts securing centrifuge drain pipe to
engine sump and discard gasket.
3.Remove turbocharger.See FUEL SYSTEM,
Repair.
Models with air conditioning only
4.Remove auxiliary drive belt.See
ELECTRICAL, Repair.
5.Remove 4 bolts securing compressor and move
to one side.
ProCarManuals.com

EMISSION CONTROL
1
REPAIR VALVE - EGR - NON EU3 MODELS
Service repair no - 17.45.01
Remove
1.Disconnect battery negative lead.
2.Remove 3 bolts and remove engine acoustic
cover.
3.Remove cooling fan.See COOLING SYSTEM,
Repair.
4.Remove battery cover.
5.Disconnect battery negative lead.
6.Disconnect vacuum hose from EGR valve
7.Loosen clip screw and release air intake from
EGR valve.
8.Remove 4 bolts, release EGR valve from inlet
manifold and discard gasket.
9.Remove 2 bolts and release EGR valve clip from
cylinder head.
10.Remove and discard 2 Allen screws securing
EGR valve pipe to exhaust manifold.
11.Remove EGR valve assembly.
12.Remove clip and remove pipe from EGR valve.Refit
13.Clean EGR valve and mating face on pipe.
14.Position pipe to EGR valve, fit retaining clip and
finger tighten bolt.
15.Clean inlet manifold face.
16.Position EGR valve to inlet manifold using new
gasket and tighten bolts to10 Nm (7lbf.ft).
17.Position air intake hose and tighten clip screw.
18.Position EGR pipe bracket, fit bolts and finger
tighten.
19.Position EGR valve pipe to exhaust manifold and
finger tighten allen screws
20.Tighten EGR valve clip to5 Nm (3 lbf.ft).
21.Tighten EGR pipe bracket bolts to10 Nm (7
lbf.ft).
22.Tighten 2 Allen screws to10 Nm (7 lbf.ft).
23.Connect vacuum hose to EGR valve.
24.Fit cooling fan.See COOLING SYSTEM,
Repair.
25.Fit engine acoustic cover.
26.Reconnect battery negative lead.
27.Fit battery cover.
ProCarManuals.com