1999 LAND ROVER DEFENDER air condition

COOLING SYSTEM
5
DESCRIPTION AND OPERATION A - EU 3 Models
B- Pre EU3 Models
GENERAL
The cooling system used on the Diesel engine is a pressure relief by-pass type system which allows coolant to
circulate around the engine block and heater circuit when the thermostat is closed. With coolant not passing
through the by-pass or the radiator promotes faster heater warm-up which in turn improves passenger comfort.
A coolant pump is mounted on a casting behind the PAS pump and is driven from the PAS pump at crankshaft
speed by the auxiliary drive belt. The pump mounting casting connects with passages in the cylinder block and
pumps coolant from the radiator through the cylinder block.
A viscous fan is attached to an idler pulley at the front of the engine. The fan is attached to a threaded spigot on
the pulley with a right hand threaded nut. The fan draws air through the radiator to assist in cooling when the
vehicle is stationary. The fan rotational speed is controlled relative to the running temperature of the engine by a
thermostatic valve regulated by a bi-metallic coil.
The cooling system uses a 50/50 mix of anti-freeze and water.
Thermostat Housing
A plastic thermostat housing is located behind the radiator. The housing has three connections which locate the
radiator bottom hose, top hose and coolant pump feed pipe. The housing contains a wax element thermostat and
a spring loaded by-pass flow valve.
Thermostat - Main valve
The thermostat is used to maintain the coolant at the optimum temperature for efficient combustion and to aid
engine warm-up. The thermostat is closed at temperatures below approximately 82°C (179°F). When the coolant
temperature reaches approximately 82°C the thermostat starts to open and is fully open at approximately 96°C
(204°F). In this condition the full flow of coolant is directed through the radiator.
The thermostat is exposed to 90% hot coolant from the engine on one side and 10% cold coolant returning from
the radiator bottom hose on the other side.
Hot coolant from the engine passes from the by-pass pipe through four sensing holes in the flow valve into a tube
surrounding 90% of the thermostat sensitive area. Cold coolant returning from the radiator, cooled by the ambient
air, conducts through 10% of the thermostat sensitive area.
In cold ambient temperatures, the engine temperature is raised approximately 10°C (50°F) to compensate for the
heat loss of 10% exposure to the cold coolant returning from the radiator bottom hose.
ProCarManuals.com

26COOLING SYSTEM
6
DESCRIPTION AND OPERATION By-pass flow valve
The by-pass flow valve is held closed by a light spring. It operates to further aid heater warm-up. When the main
valve is closed and the engine speed is below 1500 rev/min, the coolant pump does not produce sufficient flow
and pressure to open the valve. In this condition the valve prevents coolant circulating through the by-pass circuit
and forces the coolant through the heater matrix only. This provides a higher flow of warm coolant through the
heater matrix to improve passenger comfort in cold conditions.
When the engine speed increases above 1500 rev/min the coolant pump produces a greater flow and pressure
than the heater circuit can take. The pressure acts on the flow valve and overcomes the valve spring pressure,
opening the valve and limiting the pressure in the heater circuit. The valve modulates to provide maximum coolant
flow through the heater matrix and yet allowing excess coolant to flow into the by-pass circuit to provide the
engines cooling needs at higher engine rev/min.
Outlet Housing
A cast aluminium outlet housing is attached to the cylinder head with three bolts and sealed with a gasket. Coolant
leaves the engine through the outlet housing and is directed through a hose to the heater matrix, the radiator or
the by-pass circuit.
An Engine Coolant Temperature (ECT) sensor is installed in a threaded port on the side of the outlet housing. The
sensor monitors coolant temperature emerging from the engine and sends signals to the Engine Control Module
(ECM) for engine management and temperature gauge operation.
Expansion Tank
The expansion tank is located in the engine compartment. The tank is made from moulded plastic and attached to
brackets on the right hand inner wing. A maximum coolant when cold level is moulded onto the tank.
Excess coolant created by heat expansion is returned to the expansion tank from the radiator bleed pipe at the top
of the radiator. An outlet pipe is connected into the coolant pump feed hose and replaces the coolant displaced by
heat expansion into the system when the engine is cool.
The expansion tank is fitted with a sealed pressure cap. The cap contains a pressure relief valve which opens to
allow excessive pressure and coolant to vent through the overflow pipe. The relief valve is open at a pressure of
1.4 bar (20 lbf.in) and above.
Heater Matrix
The heater matrix is fitted in the heater assembly inside the passenger compartment. Two pipes pass through the
bulkhead into the engine compartment and provide coolant flow to and from the matrix. The pipes from the
bulkhead are connected to the matrix, sealed with’O’rings and clamped with circular rings.
The matrix is constructed from aluminium with two end tanks interconnected with tubes. Aluminium fins are
located between the tubes and conduct heat from the hot coolant flowing through the tubes. Air from the heater
assembly is warmed as it passes through the matrix fins. The warm air is then distributed in to the passenger
compartment as required.
When the engine is running, coolant from the engine is constantly circulated through the heater matrix.
ProCarManuals.com

COOLING SYSTEM
11
DESCRIPTION AND OPERATION OPERATION
Coolant Flow - Engine Warm Up
During warm up the coolant pump moves fluid through the cylinder block and it emerges from the outlet housing.
From the outlet housing, the warm coolant flow is prevented from flowing through the upper and lower radiators
because both thermostats are closed. The coolant is directed into the heater circuit.
Some coolant from the by-pass pipe can pass through small sensing holes in the flow valve. The warm coolant
enters a tube in the thermostat housing and surrounds 90% of the thermostat sensitive area. Cold coolant
returning from the radiator bottom hose conducts through 10% of the thermostat sensitive area. In cold ambient
temperatures the engine temperature can be raised by up to 10°C (50°F) to compensate for the heat loss of the
10% exposure to the cold coolant return from the radiator bottom hose.
At engine speeds below 1500 rev/min, the by-pass valve is closed only allowing the small flow through the sensing
holes. As the engine speed increases above 1500 rev/min, the greater flow and pressure from pump overcomes
the light spring and opens the by-pass flow valve. The flow valve opens to meet the engine’s cooling needs at
higher engine speeds and prevents excess pressure in the cooling system. With both thermostats closed,
maximum flow is directed through the heater circuit.
The heater matrix acts as a heat exchanger reducing the coolant temperature as it passes through the matrix.
Coolant emerges from the heater matrix and flows to the fuel cooler’T’connection via the heater return hose.
From the fuel cooler the coolant is directed into the coolant pump feed pipe and recirculated around the heater
circuit. In this condition the cooling system is operating at maximum heater performance.
Coolant Flow - Engine Hot
As the coolant temperature increases the main thermostat opens. This allows some coolant from the outlet
housing to flow through the top hose and into the radiator to be cooled. The hot coolant flows from the left tank in
the radiator, along the tubes to the right tank. The air flowing through the fins between the tubes cools the coolant
as it passes through the radiator.
A controlled flow of the lower temperature coolant is drawn by the pump and blended with hot coolant from the
by-pass and the heater return pipes in the pump feed pipe. The pump then passes this coolant, via the cylinder
block, to the oil cooler housing, cooling the engine oil before entering the block to cool the cylinders.
When the fuel temperature increases, the heat from the fuel conducts through the fuel cooler’T’connection and
causes the fuel thermostat to open. Coolant from the cylinder block flows through the oil cooler and via a pipe and
hose enters the lower radiator. The lower temperature coolant from the oil cooler housing is subjected to an
additional two passes through the lower radiator to further reduce the coolant temperature. From the lower radiator
the coolant flows , via a hose, to the fuel cooler.
As the hot fuel cools, travelling slowly forwards through the cooler, it meets the progressively colder coolant
travelling in the opposite direction from the lower radiator.
ProCarManuals.com

COOLING SYSTEM
1
ADJUSTMENT DRAIN AND REFILL
Service repair no - 26.10.01
WARNING: Hot coolant
Drain
1.Remove engine acoustic cover.
2.Visually check engine and cooling system for
signs of coolant leaks.
3.Examine hoses for signs of cracking, distortion
and security of connections.
4.Position drain tray to collect coolant.
5.Remove expansion tank filler cap.
6.Loosen clip screws securing air inlet hose to
intercooler and inlet manifold, release and
remove hose.
7.Release clip and disconnect bottom hose from
radiator.
8.Allow cooling system to drain.
9.Disconnect bottom hose from radiator.Refill
1.Flush system with water under low pressure.
2.Do not use water under high pressure as it could
damage the radiator.
3.Connect bottom hose to radiator and secure
hose with clip.
4.Prepare coolant to required concentration.
5.Position heater temperature control to maximum
hot position.
6.Remove bleed screw from top hose.
7.Fill system slowly through coolant expansion
tank until a steady flow of coolant is emitted from
the bleed hole in top hose.
8.Fit bleed screw to top hose.
9.Continue filling system until coolant level
reaches’MAX’mark on expansion tank.
10.Fit expansion tank filler cap.
11.Position air intake hose and tighten clip screws.
12.Start and run engine until normal running
temperature is reached.
13.If fitted, DO NOT operate air conditioning.
14.Switch off engine and allow to cool.
15.Check for leaks and top-up coolant to’MAX’
mark on expansion tank.
ProCarManuals.com

33CLUTCH
8
DESCRIPTION AND OPERATION The dual mass flywheel is bolted on the rear of the crankshaft with eight bolts. A dowel on the crankshaft flange
ensures that the flywheel is correctly located. A ring gear is fitted on the outer diameter of the flywheel. The ring
gear is not serviceable. Thirty blind holes are drilled in the outer diameter of the flywheel adjacent to the ring gear.
The holes are positioned at 10°intervals with four 20°spaces. The holes are used by the crankshaft position
sensor for engine management.
The dual mass flywheel is used to insulate the gearbox from torsional and transient vibrations produced by the
engine. The flywheel comprises primary and secondary flywheels with the drive between the two transferred by a
torsional damper which comprises four coil springs. The springs are located in the inside diameter of the primary
flywheel. Two of the springs are of smaller diameter and fit inside the larger diameter springs.
The primary flywheel locates the ring gear and is attached to the crankshaft flange with eight bolts. The two pairs
of coil springs are located in a recess in the flywheel between two riveted retainers. A roller bearing is pressed
onto the central boss of the primary flywheel and retained with a riveted plate. The bearing provides the mounting
for the secondary flywheel.
The secondary flywheel comprises two parts; an outer flywheel which provides the friction surface for the clutch
drive plate and an inner drive plate which transfers the drive from the primary flywheel, via the coil springs, to the
outer flywheel. The two components of the secondary flywheel are secured to each other with rivets. The inner
drive plate is located between the two pairs of coil springs and can rotate on the ball bearing in either direction
against the combined compression force of the four coil springs. Under high torque loading conditions the
secondary flywheel can rotate in either direction up to 70°in relation to the primary flywheel.
The operating face of the secondary flywheel is machined to provide a smooth surface for the drive plate to
engage on. Three dowels and six studs and nuts provide for the location and attachment of the pressure plate.
ProCarManuals.com

CHASSIS AND BODY
37
REPAIR
11.Remove 2 screws securing fuse cover and
remove cover.
12.Remove 7 screws securing lower edge of fascia
panel.
13.Remove footwell cover retaining plates.
14.Remove 2 nuts and remove lower fascia panel.
NOTE: Do not carry out further
dismantling if component is removed for
access only.
15.Remove 21 screws and release air duct cover.
16.Loosen trunnion screw, remove air distribution
cable and duct cover.Refit
17.Fit air distribution cable to duct cover and fit
inner cable to vent flap trunnion.
18.Tighten vent flap trunnion screw to6Nm(4
lbf.ft)and bend cable end to secure.
19.Fit duct cover to lower fascia and fit and tighten
screws.
20.Check condition of seal between heater and
lower fascia, if damaged replace.
21.Carefully fit lower fascia panel and ensure
harness route is correct.
22.Secure lower fascia panel with screws and
tighten nuts to10 Nm (7 lbf.ft).
23.Fit fuse cover and secure with screws.
24.Connect demister tubes to lower fascia panel.
25.Raise air distribution lever to screen demist
position and close footwell vent.
26.Connect air distribution cable to lever, tighten
grub screw and outer cable clamp.
27.Fit end cap to fascia and secure with screws.
28.Fit check strap covers and secure with screws.
29.Fit speakers.See ELECTRICAL, Repair.
30.Fit fascia closing panel.
31.Fit nut plate and fit screws to secure nut plate
and closing panel.
32.Fit knobs to air vent control levers.
33.Fit fascia console.See this Section.
34.Fit steering column nacelle.See STEERING,
Repair.
35.Connect battery negative lead.See
ELECTRICAL, Repair.
ProCarManuals.com

PANEL REPAIRS
1
INFORMATION BODY REPAIRS
Body shells are of riveted, bolted and welded
construction and are bolted to the chassis frame.
It is essential that design dimensions and strength are
restored in accident rectification. It is important that
neither structural weakness nor excessive local
stiffness are introduced into the vehicle during body or
chassis repair.
Repairs usually involve a combination of operations
ranging from straightening procedures to renewal of
either individual panels or panel assemblies. The
repairer will determine the repair method and this
decision will take into account a balance of economics
between labour and material costs and the availability
of repair facilities in both equipment and skills. It may
also involve considerations of vehicles down-time,
replacement vehicle availability and repair turn-around
time.
It is expected that a repairer will select the best and
most economic repair method possible, making use of
the facilities available. The instructions given are
intended to assist a skilled body repairer by expanding
approved procedures for panel replacement with the
objective of restoring the vehicle to a safe running
condition and effecting a repair which is visually
acceptable and which, even to the experienced eye,
does not advertise the fact that it has been damaged.
This does not necessarily mean that the repaired
vehicle will be identical in all respects with original
factory build. Repair facilities cannot always duplicate
methods of construction used during production.
The panel repairs shown in this section are all based
on a 110 Station Wagon. Therefore all illustrations
and text relate only to this model. Although certain
areas of the vehicle, such as the front end, are
relevant to all models.
Operations covered in this Manual do not include
reference to testing the vehicle after repair. It is
essential that work is inspected and suspension
geometry checked after completion and if necessary a
road test of the vehicle is carried out, particularly
where safety related items are concerned.Where major units have been disconnected or
removed, it is necessary to ensure that fluid levels are
checked and topped up when necessary. It is also
necessary to ensure that the repaired vehicle is in a
roadworthy condition in respect of tyre pressures,
lights, washer fluid etc.
Body repairs often involve the removal of mechanical
and electrical units as well as associated wiring.
Where this is necessary use the relevant section in
this manual.
Taking into consideration the differences in body
styles, steering and suspension systems as well as
engine and suspension layouts, the location of the
following components as applicable to a particular
vehicle is critical:
Front suspension upper damper
mountings.
Front suspension or sub frame mountings.
Engine mountings on RH and LH chassis
longitudinals.
Rear suspension upper damper mountings.
Rear suspension mountings or lower
pivots.
Steering rack mountings.
Additional points which can be used to check
alignment and assembly are:
Inner holes in crossmember - side - main
floor.
Holes in valance front assembly.
Body to chassis mounting holes.
Holes in rear floor.
Holes in rear lower panels or extension
rear floor.
Fuel tank mountings.
Apertures for windscreen, backlight, bonnet and doors
can be checked by offering up an undamaged
component as a gauge and also by measuring known
dimensions.See BODY DIMENSIONS section.
ProCarManuals.com

PANEL REPAIRS
3
INFORMATION ELECTRONIC CONTROL UNITS (ECU’s)
The ECU’s fitted to Defender vehicles make it
advisable to follow suitable precautions prior to
carrying out welding repair operations. All ECU’s must
be diconnected before any welding operations take
place. Harsh conditions of heat and vibration may be
generated during these operations which could cause
damage to the units.See ELECTRICAL
PRECAUTIONS section.
ProCarManuals.com