1999 LAND ROVER DEFENDER air condition

GENERAL FITTING REMINDERS
3
INFORMATION BALL AND ROLLER BEARINGS
CAUTION: Never refit a ball or roller
bearing without first ensuring that it is in a
fully serviceable condition.
1.Remove all traces of lubricant from bearing
under inspection by washing in a suitable
degreaser; maintain absolute cleanliness
throughout operations.
2.Inspect visually for markings of any form on
rolling elements, raceways, outer surface of
outer rings or inner surface of inner rings. Reject
any bearings found to be marked, since any
marking in these areas indicates onset of wear.
3.Holding inner race between finger and thumb of
one hand, spin outer race and check that it
revolves absolutely smoothly. Repeat, holding
outer race and spinning inner race.
4.Rotate outer ring gently with a reciprocating
motion, while holding inner ring; feel for any
check or obstruction to rotation, and reject
bearing if action is not perfectly smooth.
5.Lubricate bearing generously with lubricant
appropriate to installation.
6.Inspect shaft and bearing housing for
discolouration or other marking suggesting that
movement has taken place between bearing and
seatings. (This is particularly to be expected if
related markings were found in operation 2).
7.Ensure that shaft and housing are clean and free
from burrs before fitting bearing.8.If one bearing assembly of a pair shows an
imperfection it is generally advisable to replace
both with new bearings; an exception could be
made if the faulty bearing had covered a low
mileage, and it could be established that
damage was confined to it only.
9.When fitting bearing to shaft, apply force only to
inner ring of bearing, and only to outer ring when
fitting into housing, as shown above.
10.In the case of grease lubricated bearings (e.g.
hub bearings) fill space between bearing and
outer seal with recommended grade of grease
before fitting seal.
11.Always mark components of separable bearings
(e.g. taper roller bearings) in dismantling, to
ensure correct reassembly. Never fit new rollers
in a used outer ring, always fit a complete new
bearing assembly.
ProCarManuals.com

GENERAL FITTING REMINDERS
5
INFORMATION JOINTS AND JOINT FACES
1.Always use correct gaskets where they are
specified.
2.Use jointing compound only when
recommended. Otherwise fit joints dry.
3.When jointing compound is used, apply in a thin
uniform film to metal surfaces; take great care to
prevent it from entering oilways, pipes or blind
tapped holes.
4.Remove all traces of old jointing materials prior
to reassembly. Do not use a tool which could
damage joint faces.
5.Inspect joint faces for scratches or burrs and
remove with a fine file or oil stone; do not allow
removed material or dirt to enter tapped holes or
enclosed parts.
6.Blow out any pipes, channels or crevices with
compressed air, fit new’O’rings or seals
displaced by air blast.FLEXIBLE HYDRAULIC PIPES, HOSES
1.Before removing any brake or power steering
hose, clean end fittings and area surrounding
them as thoroughly as possible.
2.Obtain appropriate plugs or caps before
detaching hose end fittings, so that ports can be
immediately covered to exclude dirt.
3.Clean hose externally and blow through with
airline. Examine carefully for cracks, separation
of plies, security of end fittings and external
damage. Reject any hose found faulty.
4.When refitting hose, ensure that no unnecessary
bends are introduced, and that hose is not
twisted before or during tightening of union nuts.
5.Containers for hydraulic fluid must be kept
absolutely clean.
6.Do not store brake fluid in an unsealed
container. It will absorb water, and fluid in this
condition would be dangerous to use due to a
lowering of its boiling point.
7.Do not allow brake fluid to be contaminated with
mineral oil, or use a container which has
previously contained mineral oil.
8.Do not re-use brake fluid bled from system.
9.Always use clean brake fluid to clean hydraulic
components.
10.Fit a cap to seal a hydraulic union and a plug to
its socket after removal to prevent ingress of dirt.
11.Absolute cleanliness must be observed with
hydraulic components at all times.
12.After any work on hydraulic systems, inspect
carefully for leaks underneath the vehicle while a
second operator applies maximum pressure to
the brakes (engine running) and operates the
steering.
ProCarManuals.com

09LUBRICANTS, FLUIDS AND CAPACITIES
2
INFORMATION Propeller shaft Front
and RearNLGI - 2 Multi-purpose Lithium based GREASE
Lubrication nipples
(hubs, ball joints
etc.)
Seat slides
Door lock striker
Brake and clutch
reservoirsBrake fluids having a minimum boiling point of 260°C (500°F) and complying with
FMVSS 116 DOT4
Engine coolant Use Texaco XLC long life coolant. Use one part anti-freeze to one part water for
protection down to -36°C (-33°F).
IMPORTANT: Coolant solution must not fall below 50% anti-freeze otherwise
damage to engine is liable to occur. Maximun concentration is 60%.
Battery lugs, Petroleum jelly.
Earthing surfacesNOTE: Do not use Silicone Grease
where paint has
been removed
Air Conditioning
System Refrigerant Use only refrigerant R134a
Compressor Oil ND-OIL 8
LUBRICATION PRACTICE
Use a high quality oil of the correct viscosity range and service classification in the engine during maintenance and
when topping up. The use of oil not to the correct specification can lead to high oil and fuel consumption and
ultimately to damaged components.
Oil to the correct specification contains additives which disperse the corrosive acids formed by combustion and
prevent the formation of sludge which can block the oilways. Additional oil additives should not be used. Always
adhere to the recommended servicing intervals.
WARNING: Many liquids and other substances used in motor vehicles are poisonous. They must
not be consumed and must be kept away from open wounds. These substances, among others,
include anti-freeze, windscreen washer additives, lubricants and various adhesives.
ProCarManuals.com

10 - MAINTENANCE
CONTENTS
Page
MAINTENANCE
UNDERBONNET VIEW - Td5 1..............................................................................
SEATS AND SEAT BELTS 2..................................................................................
LAMPS, HORNS AND WARNING INDICATORS 2................................................
WIPERS AND WASHERS 3...................................................................................
HANDBRAKE 3.......................................................................................................
BATTERY CONDITION - Td5 4..............................................................................
HANDSET BATTERY 5...........................................................................................
HEADLAMP ALIGNMENT 5....................................................................................
ROAD WHEELS 6...................................................................................................
TYRE PRESSURES, CONDITION AND TREAD DEPTH 6....................................
BRAKE PADS, CALIPERS AND DISCS 7..............................................................
ROAD WHEEL SPEED SENSOR HARNESS - Td5 7............................................
FUEL FILTER ELEMENT 8.....................................................................................
FUEL FILTER SEDIMENTER - Td5 8.....................................................................
INTERCOOLER / COOLING SYSTEM 9................................................................
AMBIENT AIR PRESSURE (AAP) SENSOR - Td5 9..............................................
DOOR LOCKS AND HINGES 10............................................................................
ENGINE COOLANT 10...........................................................................................
BRAKE FLUID 11....................................................................................................
AIR FILTER ELEMENT AND DUMP VALVE 11.....................................................
AUXILIARY DRIVE BELT 12...................................................................................
PAS FLUID, CLUTCH FLUID AND SCREEN WASHER LEVELS 12.....................
STEERING BOX 13................................................................................................
ENGINE OIL 14.......................................................................................................
CENTRIFUGE ROTOR - Td5 14.............................................................................
FULL FLOW OIL FILTER 15...................................................................................
GEARBOX OIL 15...................................................................................................
TRANSFER BOX OIL 16.........................................................................................
FRONT AND REAR AXLE OIL 17..........................................................................
PROPELLER SHAFTS 18.......................................................................................
CLUTCH PIPES AND UNIONS 18..........................................................................
PAS PIPES AND UNIONS 19.................................................................................
ENGINE, GEARBOX, TRANSFER BOX AND AXLES 19.......................................
EXHAUST SYSTEM 20...........................................................................................
STEERING BOX AND SUSPENSION 20...............................................................
STEERING BALL JOINTS 21.................................................................................
SHOCK ABSORBERS 22.......................................................................................
TOWING BRACKET 22...........................................................................................
ENGINE AND TRANSMISSION MOUNTINGS 23..................................................
ProCarManuals.com

10MAINTENANCE
4
MAINTENANCE BATTERY CONDITION - Td5
Remove
1.Remove drivers seat base.
2.Release clip securing battery cover.
3.Remove battery cover.
NOTE: The vehicle may be fitted with an
alarm and immobilisation system. To
prevent the alarm from sounding, it is
important that the following procedure is used
when disconnecting the battery.
4.Turn the ignition switch to position’II’, and then
to position’0’.
5.Remove the ignition key.
6.Disconnect the vehicle -ve terminal within 15
seconds.
NOTE: Always disconnect the -ve terminal
first. When replacing, connect the +ve
terminal first.
Check
The battery fitted to Td5 models is designed to be
maintenance free, so topping-up is not possible. On
the top of the battery is a battery indicator. When the
indicator shows:
GREEN - The battery is in a good state of charge.
DARK (turning to black) - The battery needs
charging.
CLEAR (or light yellow) - The battery needs
replacing. Do not charge the battery or jump start
the vehicle in this condition.
If the green dot is missing, the battery needs
charging.
NOTE: If the indicator shows clear or
yellow, tap the indicator with the handle of
a screwdriver to disperse any air bubbles.
If the indicator colour remains unchanged, the
battery will need replacing.
Refit
7.Clean and grease battery terminals and leads
with petroleum jelly.
8.Connect leads to battery (+ve first) and tighten
clamp bolts.
9.Fit battery cover and secure with clip.
10.Fit drivers seat base.
ProCarManuals.com

MAINTENANCE
9
MAINTENANCE INTERCOOLER / COOLING SYSTEM
1.Visually check for any obstructions in the
radiator and intercooler matrix and remove
debris as necessary.
2.Visually check fan blades for damage.
3.Check cooling, intercooler and heating systems
for leaks, hoses and oil pipes for security and
condition.
4.Check accessible hose clips for tightness.
5.Check coolant level, top-up if necessary
Cooling System Top-Up
1.With engine cold, remove expansion tank filler
cap.
2.Top-up with recommended mixture of coolant
until level reaches mark on expansion tank.
3.Fit expansion tank filler cap.
Intercooler Flush
1.Remove intercooler.See FUEL SYSTEM,
Repair.
2.Flush intercooler element using Unicorn
Chemicals’C’Solve following the manufaturers
instructions.
3.Thoroughly dry intercooler ensuring that no trace
of solvent remains in the element.
4.Refit intercooler.See FUEL SYSTEM, Repair.AMBIENT AIR PRESSURE (AAP) SENSOR - Td5
1.Check ambient air pressure sensor for damage.
ProCarManuals.com

10MAINTENANCE
20
MAINTENANCE EXHAUST SYSTEM
1.Visually check condition of exhaust system for
signs of damage.
2.Check condition of exhaust heat shields.
3.Check exhaust system is firmly secured and
check condition of exhaust mounting rubbers,
clamps and brackets.STEERING BOX AND SUSPENSION
1.Check steering box fixings. Tighten if necessary
to81 Nm (60 lbf.ft).
2.Check LH and RH front radius arm fixings.
Tighten if necessary.See FRONT
SUSPENSION, Repair.
3.Check Panhard rod fixings. Tighten if necessary.
See FRONT SUSPENSION, Repair.
4.Check all rear axle fixings. Tighten if necessary.
ProCarManuals.com

MAINTENANCE
23
MAINTENANCE ENGINE AND TRANSMISSION MOUNTINGS
1.Check condition of front LH engine mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
2.Check condition of front RH engine mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
3.Check condition of rear LH gearbox mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
4.Check condition of rear RH gearbox mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.ROAD TEST
There are two purposes for conducting a road test.
Firstly, to ensure the work completed within the
dealership meets the standards required as layed
down by dealership processes. Secondly, for a skilled
technician to assess the general condition of the
vehicle and report any conditions that the customer
should be made aware of.
CAUTION: Two wheel roller tests must not
be carried out. Four wheel roller tests
must be restricted to 3 mph (5 kph).
1.Check for correct operation of starter switch.
Ensure the engine starts in a correct manner.
Leave the engine running.
2.With vehicle stationary, turn steering from lock to
lock. Check for smooth operation and ensure
there is no undue noise from the power steering
pump or drive belt.
3.Depress clutch and select all gears in turn.
Check for smooth notch free engagement.
4.Drive vehicle on a short road test. Check all
vehicle systems for correct operation. Pay
particular attention to:
Engine noise
Gearbox noise
Suspension noise
Body noise
Braking system operation
Gear selection
Engine performance
5.Check for correct operation of all instruments
and warning devices where practical.
6.After road test, carry out a final inspection of the
vehicle on vehicle ramps.
7.Check all underbonnet fluid levels and top-up if
necessary.
ProCarManuals.com