1999 LAND ROVER DEFENDER air condition

EMISSION CONTROL
9
DESCRIPTION AND OPERATION EGR MODULATOR
1.Port to vacuum source (white band)
2.Port to EGR valve (blue band)3.Port to atmosphere via in-line filter (green band)
4.Harness connector
The EGR modulator is located on a plate fixed to the inner RH front wing. The modulator is attached to the plate
by two studs, each with two nuts which secure the assembly to a rubber mounting, which helps reduce noise. The
modulator must be mounted vertically with the two vacuum ports uppermost.
Modulator operation is controlled by a signal from the ECM which determines the required amount of EGR needed
in response to inputs relating to air flow, engine operation, and ambient conditions. The modulator has a two pin
connector at its base to connect it to the ECM via the engine harness.
The modulator features three ports:
The top port is identified by a white band and connects to a T-piece in the vacuum line via a small bore light
brown plastic hose. The two other ports on the T-piece connect to the vacuum line hoses of black vinyl tubing
between the vacuum pump and the brake servo assembly attached to the bulkhead. The vacuum pump end of
the tubing terminates in a rubber elbow, which gives a vacuum tight seal on the suction port of the vacuum
pump. The brake servo end of the tubing terminates with a non-return valve in a plastic housing which plugs
into the front face of the brake servo housing.
The middle port is identified by a blue band, and connects to the suction port on the EGR valve through a small
bore blue plastic hose.
The lower port is identified by a green band and connects to atmosphere through an in-line filter via a small
bore green plastic hose.
The blue and brown vacuum hoses are protected by corrugated plastic sheaths. The ends of the hoses are fitted
with rubber boots to ensure vacuum tight seals at the component ports.
ProCarManuals.com

17EMISSION CONTROL
10
DESCRIPTION AND OPERATION INLET THROTTLE (ILT) MODULATOR
1.Port to vacuum source (white band)
2.Port to ILT valve (blue band)
3.Port to atmosphere via in-line filter (green band)
4.Harness connector (green)
The ILT modulator is located on a plate fixed to the inner wing on the RH side of the engine below the EGR
modulator. The modulator is attached to the plate by two through-studs, each with two nuts which secure the
modulator assembly to a rubber mounting which helps to reduce noise. The modulator must be mounted in the
vertical orientation with the two vacuum ports uppermost.
The modulator operation is controlled by a signal from the ECM which determines the required ratio of exhaust
gas to fresh inlet air needed in response to inputs relating to air flow and engine operating and ambient conditions.
The modulator has a green two-pin connector at its base to connect it to the ECM through the engine harness.
The ILT valve modulator features three ports:
The top port is identified by a white band and connects to a’T’-piece in the vacuum line via a small-bore brown
plastic hose where it is connected in parallel with the vacuum source line to the EGR valve modulator. The two
other ports on the’T’-piece connect vacuum line hoses of black vinyl tubing between the vacuum pump
attached to the alternator and the brake-servo assembly attached to the bulkhead.
The middle port is identified by a blue band and connects to the suction port on the ILT valve through a
small-bore blue plastic hose.
The lower port is identified by a green band and connects to atmosphere through an in-line filter via a green
plastic hose and a three-way connector positioned in-line between the modulators and the filter. The ILT
modulator hose is connected opposite to the two parallel ports at the three-way connector which connect the
vent lines to the EGR valve modulator and the in-line filter. The other port of the in-line filter vents directly to
atmosphere.
The blue and brown vacuum hoses are protected by corrugated plastic sheaths. The ends of the hoses are fitted
with rubber boots to ensure vacuum tight seals at the component ports.
ProCarManuals.com

17EMISSION CONTROL
14
DESCRIPTION AND OPERATION EGR SYSTEMS
There are two types of exhaust gas recirculation system used with the Td5 engine dependent on legislation and
market requirements, these are type 1 and type 2.
Type 1 EGR system is fitted to all Td5’s built up to the introduction of 2002 MY, except for Japanese specification
vehicles.
Type 2 EGR system is fitted to all Japanese specification vehicles and was introduced into European markets for
2002 MY to meet EU3 emission requirements. An additional feature introduced at 2002 MY is the EGR cooler,
which is bolted to the front of the cylinder head.
EGR System - Type 1
This EGR system features a modulator which is electrically controlled to modulate a vacuum source to the EGR
valve. The controlled vacuum opens the valve by the amount required to ensure the optimal proportion of exhaust
gas is allowed through to the inlet manifold to be combined with the fresh air intake. Control feedback is achieved
by monitoring the mass of fresh air flowing through the MAF sensor.
EGR modulator operation is controlled by a signal from the ECM, which determines the required amount of EGR
needed in response to inputs relating to air flow and engine operating and ambient conditions. The ECM is
low-side driven, sinking current returned from the vacuum modulator for switching operating condition.
The exhaust gases are routed from the exhaust manifold through a shaped metal pipe which connects to the
underside of the EGR valve. The pipe is held securely in position to the front of the cylinder head using a clamp
bracket. The EGR pipe is attached to a mating port at the front end of the exhaust manifold using 2 Allen screws,
and at the EGR valve assembly by a metal band clamp. The 2 Allen screws should be replaced every time the
EGR pipe is removed.
CAUTION: Extreme caution should be exercised when removing and refitting the EGR pipe to
avoid damage.
When a vacuum is applied to the EGR suction port, it causes a spindle with sealing disc (EGR valve) to be raised,
thus opening the port at the EGR pipe to allow the recirculated exhaust gas to pass through into the inlet manifold.
The valve is spring loaded so that when the vacuum is removed from the suction port the valve returns to its rest
position to tightly close the exhaust gas port.
By controlling the quantity of recirculated exhaust gas available in the inlet manifold, the optimum mix for the
prevailing engine operating conditions can be maintained. This ensures the intake gas to the combustion
chambers will have burning rate properties which will reduce NO
Xemissions to an acceptable level. Normally, full
recirculation is only applicable when NO
Xemissions are most prevalent.
ProCarManuals.com

EMISSION CONTROL
15
DESCRIPTION AND OPERATION EGR System - Type 2
This system features twin modulators mounted one above the other on a metal plate located on the inner wing at
the RH side of the engine. The modulators are electrically controlled by the engine management system and are
used to modulate a vacuum source to the EGR valve and a supplementary Inlet Throttle (ILT) valve; the two
valves are controlled to operate in tandem. The ILT valve vacuum pot is mounted adjacent to the EGR valve
housing and has a linkage which connects to a butterfly valve mounted in front of the EGR valve at the air intake
manifold.
The modulator operations are electrically controlled by signals from the engine management system which
determines the required volume of exhaust gas needed in response to inputs relating to air flow, engine operating
conditions and ambient parameters such as temperature and altitude. The engine management ECM switches on
the circuit by completing the path to ground, operating the vacuum modulators.
Pre EU3 models:The exhaust gases are routed from the exhaust manifold through a shaped metal pipe which
connects to the underside of the EGR valve. The pipe is held securely in position to the front of the engine cylinder
head using a metal clamp bracket. The EGR pipe is attached to a mating port at the front end of the exhaust
manifold using two Allen screws and at the EGR valve assembly by a metal band clamp. The two Allen screws
fixing the EGR pipe to the exhaust manifold should be replaced every time the EGR pipe is removed.
CAUTION: Extreme care should be exercised when removing and refitting the EGR pipe to avoid
damage.
EU3 models:The exhaust gases are routed from the exhaust manifold through the EGR cooler to the underside
of the EGR valve. The EGR cooler is bolted to the front of the engine cylinder head. An EGR pipe connects the
EGR cooler to the exhaust manifold and is secured by two Allen screws. The two Allen screws fixing the EGR pipe
to the exhaust manifold should be replaced every time the EGR pipe is removed. A second pipe connects the
EGR cooler to the EGR valve; this pipe is secured to the EGR valve by a clip, and to the cooler by two Allen
screws.
CAUTION: Extreme care should be exercised when removing and refitting the EGR pipe to avoid
damage. When refitting the EGR cooler, always tighten the pipe connections BEFORE tightening
the bolts securing the cooler to the cylinder head.
When a vacuum is applied to the EGR suction port, it causes a spindle with sealing disc (EGR valve) to be raised,
opening the port at the EGR pipe to allow the recirculated exhaust gas to pass through into the inlet manifold. The
valve is spring loaded so that when the vacuum is removed from the suction port, the valve returns to its rest
position to tightly close the exhaust gas port.
A vacuum is simultaneously applied to the inlet throttle (ILT) valve suction port which causes the butterfly valve in
the inlet manifold to close by means of a spindle and lever mechanism. Closing the butterfly valve limits the supply
of fresh intercooled air entering the inlet manifold and causes a depression within the inlet manifold to create a
greater suction at the open port to the EGR delivery pipe. In this condition a greater mass of recirculated exhaust
gas is drawn into the inlet manifold for use in the combustion process. When the vacuum is released from the ILT
valve suction port a spring returns the butterfly valve to its fully open position.
By controlling the quantities of recirculated exhaust gas and fresh intake air available in the inlet manifold, the
optimum mix for the prevailing engine operating conditions can be maintained which ensures the intake gas to the
combustion chambers will have burning rate properties which will reduce the NO
2emissions to an acceptable
level. Normally, full recirculation is only applicable when the NO
2emissions are most prevalent.
ProCarManuals.com

ENGINE MANAGEMENT SYSTEM
3
DESCRIPTION AND OPERATION 1.Mass Air Flow (MAF) sensor.
2.Engine Coolant Temperature (ECT) sensor.
3.Glow plugs.
4.Manifold Absolute Pressure (MAP) / Inlet Air Temperature (IAT) sensor.
5.Fuel pump relay.
6.Engine Control Module (ECM).
7.Air Conditioning (A/C) and cooling fan relay.
8.Fuel Temperature (FT) sensor.
9.Crankshaft Speed and Position (CKP) sensor.
10.Electronic Unit Injectors (EUI).
11.Ambient Air Pressure (AAP) sensor.
ProCarManuals.com

ENGINE MANAGEMENT SYSTEM
5
DESCRIPTION AND OPERATION DESCRIPTION
General
An engine control module (ECM) controls the five cylinder direct injection diesel engine, and works on the drive by
wire principal. This means there is no throttle cable, the ECM controls the drivers needs via a signal from the
Throttle Position (TP) sensor on the throttle pedal.
The ECM is a full authoritative diesel specific microprocessor that also incorporates features for air conditioning. In
addition, the ECM supplies output control for the Exhaust Gas Recirculation (EGR) and turbocharger boost
pressure. The ECM has a self diagnostic function, which is able to provide backup strategies for most sensor
failures.
The ECM processes information from the following input sources:
Mass Air Flow (MAF) sensor.
Ambient Air Pressure (AAP) sensor.
Manifold Absolute Pressure (MAP) / Inlet Air Temperature (IAT) sensor.
Engine Coolant Temperature (ECT) sensor.
Crankshaft Speed and Position (CKP) sensor.
Throttle Position (TP) sensor.
Fuel Temperature (FT) sensor.
Air conditioning request.
Air conditioning fan request.
Brake pedal switch.
Clutch pedal switch.
The input from the sensors constantly updates the ECM with the current operating condition of the engine. Once
the ECM has compared current information with stored information within its memory, it can make any adjustment
it requires to the operation of the engine via the following:
Air conditioning clutch relay.
Air conditioning cooling fan relay.
Electronic vacuum regulator solenoid.
Fuel pump relay.
Glow plug warning lamp.
Glow plugs.
Fuel injectors.
Main relay.
Turbocharger wastegate modulator.
Temperature gauge.
The ECM interfaces with the following:
Serial communication link.
Instrument pack.
ProCarManuals.com

ENGINE MANAGEMENT SYSTEM
7
DESCRIPTION AND OPERATION SENSOR - MASS AIR FLOW (MAF)
The MAF sensor is located in the intake system between the air filter housing and the turbocharger. The ECM
uses the information generated by the MAF sensor to control exhaust gas recirculation (EGR).
The MAF sensor works on the hot film principal. The MAF sensor has 2 sensing elements contained within a film.
One element is controlled at ambient temperature e.g. 25°C (77°F) while the other is heated to 200°C (360°F)
above this temperature e.g. 225°C (437°F). As air passes through the MAF sensor the hot film will be cooled.
The current required to keep the constant 200°C (360°F) difference provides a precise although non-linear signal
of the air drawn into the engine. The MAF sensor sends a voltage of between 0 and 5 volts to the ECM,
proportional to the mass of the incoming air. This calculation allows the ECM to set the EGR ratio for varying
operating conditions.
Inputs / Outputs
The MAF sensor receives battery voltage (C0149-3) via the ECM on a brown/orange wire. Signal output on a
slate/light green wire from the MAF sensor (C0149-2) to the ECM (C0158-11) is a variable voltage proportional to
the air drawn into the engine. The MAF sensor is provided an earth (C0149-1) via the ECM (C0158-20) on a
pink/black wire.
The MAF sensor can fail or supply an incorrect signal if one or more of the following occurs:
Sensor open circuit.
Short circuit to vehicle supply.
Short circuit to vehicle earth.
Contaminated sensor element.
Damaged sensor element.
Damaged wiring harness.
MAF sensor supplies incorrect signal (due to air leak or air inlet restriction).
In the event of a MAF sensor signal failure any of the following symptoms my be observed:
During driving, engine speed may dip before recovering.
Difficult starting.
Engine stalls after starting.
Delayed throttle response.
EGR inoperative.
Reduced engine performance.
MAF signal out of parameters.
In the event of a MAF sensor failure, the ECM will use a fixed default value from its memory.
ProCarManuals.com

18ENGINE MANAGEMENT SYSTEM
28
DESCRIPTION AND OPERATION OPERATION
Engine Management
The ECM controls the operation of the engine using stored information within its memory. This guarantees
optimum performance from the engine in terms of torque delivery, fuel consumption and exhaust emissions in all
operating conditions, while still giving optimum driveability.
The ECM will receive information from its sensors under all operating conditions, especially during:
Cold starting.
Hot starting.
Idle.
Wide open throttle.
Acceleration.
Adaptive strategy.
Backup strategy for sensor failures.
The ECM receives information from various sensors to determine the current operating state of the engine. The
ECM then refers this information to stored values in its memory and makes any necessary changes to optimise
air/fuel mixture and fuel injection timing. The ECM controls the air/fuel mixture and fuel injection timing via the
Electronic Unit Injectors (EUI), by the length of time the EUI’s are to inject fuel into the cylinder. This is a rolling
process and is called adaptive strategy. By using this adaptive strategy the ECM is able to control the engine to
give optimum driveability under all operating conditions.
During cold start conditions the ECM uses ECT information to allow more fuel to be injected into the cylinders.
This, combined with the glow plug timing strategy supplied by the ECM, facilitates good cold starting.
During hot start conditions, the ECM uses ECT and FT information to implement the optimum fuelling strategy to
facilitate good hot starting.
During idle and wide open throttle conditions, the ECM uses mapped information within its memory to respond to
input information from the TP sensor to implement the optimum fuelling strategy to facilitate idle and wide open
throttle.
To achieve an adaptive strategy for acceleration, the ECM uses input information from the CKP sensor, the TP
sensor, the ECT sensor, the MAP/IAT sensor, and the FT sensor. This is compared to mapped information within
its memory to implement the optimum fuelling strategy to facilitate acceleration.
Fuel Delivery / Injection Control
The fuel delivery/injection control delivers a precise amount of finely atomised fuel to mix with the air in the
combustion chamber to create a controlled explosion. To precisely control fuel delivery and control fuel injection,
the following input conditions must be met:
CKP information.
Injection timing map information.
FT information.
ECT information.
The ECM monitors the conditions required for optimum combustion of fuel in the cylinder from the various sensors
around the engine and then compares it against stored information. From this calculation, the ECM can adjust the
quantity and timing of the fuel being delivered into the cylinder. The ECM uses CKP information as follows:
To calculate engine speed.
To determine engine crankshaft position.
Engine speed and crankshaft position allows the ECM to determine fuel injection timing.
The ECM also uses ECT and FT information to allow optimum fuel delivery and injection control for all engine
coolant and fuel temperatures.
ProCarManuals.com