1999 LAND ROVER DEFENDER warning

ELECTRICAL
15
DESCRIPTION AND OPERATION CENTRAL DOOR LOCKING (CDL) - FROM 02MY
The Central Door Locking (CDL) system is a new feature for 2002MY Defender.
NOTE: CDL operates all doors on Station Wagon and County Station Wagons. On all other
Defender 2002MY variants, CDL operates on the driver and front and rear passenger doors only.
General
CDL operates on all doors, including the tail door and is operated by pressing the appropriate button on the
remote handset, using the vehicle key in the drivers door lock or using the drivers door sill button.
The CDL system introduces electrically operated door latches which are controlled by the anti-theft alarm ECU,
located behind the instrument pack. The anti-theft ECU receives a permanent power supply from fuse 6 in the
passenger compartment fuse box. Each CDL latch motor is connected by two wires to the anti-theft ECU which
alternately supplies power and earth connections to drive each motor to the lock or unlock positions.
If the latch motors are continually operated in a short period of time, the anti-theft ECU will suspend all CDL latch
motor operation for 15 seconds to prevent the motors from overheating. Before suspension occurs the anti-theft
ECU ensures that all the doors are left in the unlocked condition.
If the vehicle is locked, and the key is in the ignition switch or the ignition is on and the anti-theft alarm ECU inertia
switch is tripped, all doors will be unlocked immediately and the hazard warning lamps will operate. To prevent
accidental relocking, all latch motors will be inhibited until the anti-theft ECU senses that the drivers door is
opened with the key removed from the ignition switch.
Locking of the vehicle using the remote handset is inhibited with the key in the ignition switch.
Slam Locking
With the introduction of CDL, slam locking of the drivers door is disabled. If an attempt is made to slam lock the
vehicle, the anti-theft alarm ECU will unlock all doors.
CDL Using the Drivers Door Sill Button
Each door has a sill button to allow that door to be individually locked from inside the vehicle. The drivers door sill
button has additional functionality which allows all doors to be locked from inside the vehicle from this one button.
When the driver door sill lock button is depressed, the CDL system enters a sill locked state, where all doors are
locked but immobilisation and perimetric and volumetric sensing is suspended. CDL using the drivers sill lock
button can be achieved with or without the key in the ignition switch and without the ignition being on.
If the CDL is in the sill locked state and the lock button on the remote handset is pressed, the volumetric and
perimetric functions of the alarm system will become active and active engine immobilisation will be invoked.
ProCarManuals.com

ELECTRICAL
17
DESCRIPTION AND OPERATION Interior Lamp Functionality
The anti-theft alarm ECU controls the interior lamp functionality. When the lamps are extinguished, they fade out
to the off condition over a 2 second period.
The lamps are turned on by:
Disarming the alarm using the remote handset
Opening any door.
When the lamps are on, they will be extinguished by the following actions:
If all doors are closed, the lamps will be extinguished after a 15 second delay period
If any door is left open, the lamps will be extinguished after an 8 minute delay period
If one of the above delay periods is active and the ignition is switched on or the alarm is armed, the lamps will
be extinguished.
ANTI-THEFT ALARM SYSTEM SELF TEST
The anti-theft alarm ECU has a self test feature which allows all alarm inputs to be tested. To enter self test mode
the following steps must be completed as follows:
1.Ensure that the driver’s door is closed and the driver’s window is open
2.Open the bonnet and with assistance depress and hold the bonnet switch
3.Release the bonnet switch and within 0.5 seconds turn the ignition switch on to position II
4.Quickly open the driver’s door
5.Turn the ignition switch to the off position
6.Turn the ignition switch back to position II
7.If the self test mode has been entered successfully, confirmation will be given by the alarm sounder. If the
ECU has not entered self test mode, repeat the above procedure.
Once in self test mode, the following test inputs will cause the security LED to illuminate and the engine
immobilised warning lamp and the hazard warning lamps to flash. When an input is operated, non illumination of
the security LED, the engine immobilised warning lamp and the hazard warning lamps indicates a fault for that
input.
Perform the following steps to test each input for correct operation:
Close and open the drivers door
Open and close each of the passenger doors and the tail door in turn
Close and open the bonnet (depress switch if bonnet still open)
With drivers door closed, lock and unlock the driver’s door using the vehicle key if spare key available. If spare
key is not available, operate driver’s sill button through open window
Press the unlock button of the remote handset. This enters the volumetric self test mode and all other inputs
will be disabled. Make a movement inside the vehicle. When the volumetric sensor is triggered the security
LED will flash.
To exit the self test mode, turn the ignition switch to the off position.
ProCarManuals.com

86ELECTRICAL
18
DESCRIPTION AND OPERATION FASCIA CONSOLE
1.Rear fog lamp switch
2.Rear wiper switch
3.Heated front screen switch (if fitted)
4.Hazard warning lamp switch
5.Heated rear window switch
6.Rear washer switch
7.Front fog lamps switch (if fitted)8.RH front window switch
9.RH heated front seat switch (if fitted)
10.Headlamp levelling control switch
11.Cigar lighter (if fitted)
12.LH heated front seat switch (if fitted)
13.LH front window switch
ProCarManuals.com

ELECTRICAL
19
DESCRIPTION AND OPERATION For 02MY a new fascia console has been introduced to accommodate the additional switches for electric windows
etc.
The console comprises a plastic moulding secured to the fascia with five screws. The new console allows existing
switches to be repositioned and has provided the opportunity to commonise the switches with other Land Rover
models. The switches and components located in the console are as follows:
Cigar lighter (if fitted)
Headlamp levelling control
LH and RH heated front seat switches (if fitted)
LH and RH front window lift switches
Front fog lamp switch (if fitted)
Rear fog lamp switch
Rear wash/wipe switch
Rear wiper switch
Hazard warning lamp switch
Heated rear window switch
Heated front screen switch (if fitted)
A central cut-out in the console provides for the installation of the radio, where fitted, or a coin tray for markets
without a standard radio installation.
ProCarManuals.com

86ELECTRICAL
26
DESCRIPTION AND OPERATION PASSENGER COMPARTMENT FUSE BOX
FROM 02MY
The increase in electrical systems on Defender 02MY vehicles has necessitated an increase in the number of
fuses required.
The passenger compartment fuse box now contains three rows of fuses instead of the previous two rows and
relays to control the CDL system, heated front screen, headlamps, anti-theft alarm ECU and seat heaters and
window lift system.
1.Fuse 8 - Anti-theft alarm ECU/BBUS (10A)
2.Fuse 9 - Front wiper motor and washer pump
(15A)
3.Fuse 10 - Rear wiper relay (10A)
4.Fuse 11 - ABS ECU (10A)
5.Fuse 12 - Engine Control Module (10A)
6.Fuse 13 - Brake pedal switch (10A)
7.Fuse 14 - Reverse lamp switch/Glowplugs (10A)
8.Fuse 15 - Miscellaneous relay control. See
Electrical Library (5A)
9.Fuse 16 - Cigar lighter/Heater blower (20A)
10.Fuse 17 - Radio (5A)
11.Fuse 18 - LH side lamps/trailer pick up (10A)
12.Fuse 19 - RH side lamps/trailer pick up (10A)
13.Fuse 20 - Headlamp levelling/Illumination (10A)
14.Fuse 21 - Direction indicators (10A)
15.Fuse 22 - RH headlamp dip beam (10A)
16.Fuse 23 - LH headlamp dip beam (10A)
17.Fuse 24 - RH headlamp main beam (10A)
18.Fuse 25 - LH headlamp main beam (10A)19.Fuse 26 - Rear fog lamp ECU (10A)
20.Fuse 27 - Alarm relay (10A)
21.Fuse 28 - Air conditioning blower relay (30A)
22.Fuse 29 - Air conditioning compressor
relay/cooling fan relay (20A)
23.Fuse 30 - Interior lamps/radio/alarm
LED/clock/diagnostic socket/tachometer (South
African vehicles only) (5A)
24.Fuse 31 - Hazard warning lamps (15A)
25.Fuse 32 - Heated rear window (20A)
26.Fuse 33 - Seat heat relay (20A)
27.Fuse 34 - RH window lift switch (20A)
28.Fuse 35 - LH window lift switch (20A)
29.Fuse 36 - Heated front screen (30A)
30.Relay - Heated Front Screen
31.Relay - Starter motor
32.Relay - Heated Rear Window
33.Relay - Headlamps
34.Relay - Anti-theft alarm
35.Relay - Seat heat/window lift
ProCarManuals.com

ELECTRICAL
7
REPAIR SPEAKER - FRONT
Service repair no - 86.50.15
Remove
1.Remove 4 screws securing speaker to fascia.
2.Release speaker from fascia and disconnect 2
Lucars.
3.Remove speaker.
Refit
4.Position speaker to fascia and connect Lucars.
5.Fit speaker to fascia and secure with screws.SWITCH - TRANSMISSION BRAKE
Service repair no - 86.65.45
Remove1.Release cover from transmission brake lever.
2.Remove 2 bolts and release transmission brake
lever from body.
3.Disconnect Lucar from transmission brake
warning switch.
4.Remove 2 screws securing switch from brake
lever and remove switch.
Refit
5.Fit switch to brake lever and tighten screws.
6.Connect switch Lucar.
7.Position brake lever and tighten bolts to22 Nm
(16 lbf.ft).
8.Position cover to brake lever.
ProCarManuals.com

86ELECTRICAL
16
REPAIR LAMP ASSEMBLY - CENTRE HIGH MOUNTED
STOP LIGHT (CHMSL) - FROM 02MY
Service repair no - 86.41.32
Remove
1.Open rear door.
2.Remove 2 screws and cover from CHMSL.
3.Remove insulated cover from Lucar connector,
release catch’s and disconnect Lucar’s taking
care not to damage screen element.
4.Remove nuts securing lamp to rear screen,
withdraw lamp assembly, collect seals and
washers.
5.Remove rubber backing pad, taking care not to
damage screen obscuration band.
Refit
6.Clean obscuration band and fit new backing pad.
7.Fit lamp assembly, seals and washers. Fit nuts
and tighten to3 Nm (2.2 lbf.ft).
8.Insulate Lucar connector.
9.Connect Lucars to heated rear screen.
10.Fit cover to CHMSL and secure with screws.FLASHER UNIT - HAZARD WARNING - FROM
02MY
Service repair no - 86.55.12
Service repair no - 86.55.15
NOTE: This procedure also covers
removal of the Heated Front Screen Timer
Relay, 86.55.15.
Remove
1.Disconnect battery negative lead.See this
Section.
2.Remove 4 screws securing instrument pack and
release pack from fascia.
3.Disconnect 2 multiplugs from warning lamp
panel.
4.Disconnect instrument pack multiplug from main
harness.
5.Remove instrument pack.
ProCarManuals.com

86ELECTRICAL
18
REPAIR RELAY - REAR FOG GUARD - FROM 02MY
Service repair no - 86.55.53
Remove
1.Disconnect battery negative lead.See this
Section.
2.Remove 4 screws securing instrument pack and
release pack from fascia.
3.Disconnect 2 multiplugs from warning lamp
panel.
4.Disconnect instrument pack multiplug from main
harness.
5.Remove instrument pack.
6.Remove screw securing relay bracket,
disconnect multiplug and remove relay.
Refit
7.Fit relay, connect multiplug and secure relay with
screw.
8.Position instrument pack and connect multiplugs.
9.Fit instrument pack to fascia and secure with
screws.
10.Connect battery negative lead.See this
Section.
ProCarManuals.com