1999 LAND ROVER DEFENDER warning

WIPERS AND WASHERS
5
REPAIR
9.Remove cable ties securing washer tube to
windscreen wiper rack tube.
10.Loosen fully 4 nuts securing backplates to wheel
boxes and remove windscreen wiper rack tubes.
11.Remove seals from wheel box spindles.
12.Remove 2 nuts securing wheel boxes and
remove sealing washers.
13.Carefully pull fascia support rail from bulkhead
sufficiently to remove wheel boxes.
Refit
14.Loosen fully but do not remove nuts securing
wheel box back plates.
15.Grease wheel boxes.
16.Fit wheel boxes, fit sealing washers and tighten
nuts to5 Nm (3.7 lbf.ft).
17.Fit spindle seals.
18.Fit wiper rack tubes and tighten wheel box back
plate nuts sufficiently to hold tubes. Tighten
wheel box back plate nuts to6 Nm (4 lbf.ft)
after fitting windscreen wiper motor.
19.Align washer tube to rack tube and secure with
cable ties.
20.Align fascia support rail and secure with screws.
21.Fit steering column support bracket and tighten
bolt and nut and bolt to45 Nm (33 lbf.ft).
22.Fit demister duct to tube, align relay bracket and
secure duct with screws.
23.Position heater fan switch and secure with
screws.
24.Fit wiper motor and drive rack.See this
Section.
25.Fit steering column nacelle.See STEERING,
Repair.
26.Connect battery negative lead.See
ELECTRICAL, Repair.RELAY - WIPER DELAY - FROM 02MY
Service repair no - 84.15.37
Remove
1.Disconnect battery negative lead.See
ELECTRICAL, Repair.
2.Remove 4 screws securing instrument pack and
release pack from fascia.
3.Disconnect 2 multiplugs from warning lamp
panel.
4.Disconnect instrument pack multiplug from main
harness.
5.Remove instrument pack.
ProCarManuals.com

86 - ELECTRICAL
CONTENTS
Page
LAMP ASSEMBLY - CENTRE HIGH MOUNTED STOP LIGHT (CHMSL) -
FROM 02MY 16......................................................................................................
FLASHER UNIT - HAZARD WARNING - FROM 02MY 16.....................................
RELAY - HEATED FRONT SCREEN - FROM 02MY 17........................................
RELAY - REAR FOG GUARD - FROM 02MY 18...................................................
RELAY - STARTER - FROM 02MY 19...................................................................
SWITCH - HEADLAMP LEVELLING - FROM 02MY 19.........................................
CIGAR LIGHTER - FRONT - FROM 02MY 20........................................................
ProCarManuals.com

ELECTRICAL
1
DESCRIPTION AND OPERATION SECURITY AND CENTRAL DOOR LOCKING
SYSTEM - FROM 02MY
The following description details the functionality and operation of the 10AS Security and Central Door Locking
(CDL) System fitted to 2002MY Defender. The system contains some new features and also retains some
features from previous Defender models. The alarm system and CDL system are controlled by the 10AS anti-theft
alarm ECU.
New door lock barrels are introduced and use the same key as the ignition switch barrel, thereby eliminating the
requirement for a separate key for the doors.
NOTE: Some markets will only have some of the features described and some will have no
security or central door locking functions.
The security system comprises the following components:
10AS anti-theft alarm ECU
Remote handset transmitters
Transponder coil
Volumetric sensor
CDL actuators
Bonnet switch
Driver’s door key barrel switch
Door switches
Bonnet switch
Battery Backed-Up Sounder (BBUS) or alarm sounder
Security LED
Engine immobilised warning lamp
Direction indicators
ProCarManuals.com

86ELECTRICAL
2
DESCRIPTION AND OPERATION SECURITY AND CENTRAL DOOR LOCKING
SYSTEM COMPONENTS - FROM 02MY
1.Engine immobilisation warning lamp
2.Security LED
3.Transponder coil
4.CDL actuators (tail door shown)
5.Immobilisation ECU (300Tdi models only)
6.Remote handset and key7.Door switches
8.Bonnet switch
9.Alarm sounder
10.Battery Backed Up Sounder (BBUS)
11.Anti-theft alarm ECU
12.Volumetric sensor
ProCarManuals.com

ELECTRICAL
3
DESCRIPTION AND OPERATION ANTI-THEFT ALARM - FROM 02MY
The alarm and immobilisation system on 2002MY Defender is similar to that used on Discovery Series I (LJ)
models from 1996MY. The alarm system comprises the anti-theft alarm ECU, bonnet and door switches and a
volumetric sensor.
Anti-Theft Alarm ECU
The anti-theft alarm ECU is located behind the instrument pack and receives a permanent battery supply via fuses
6 and 7 in the under seat fuse box. The ECU also receives a battery supply via the ignition switch position II and
fuse 1 in the passenger compartment fuse box. The ECU is connected to the various supporting components by
two harness connectors.
The ECU controls the alarm system (perimetric and volumetric security), CDL system, engine immobilisation
system (Td5 only) and various other vehicle functions including direction indicators and interior lamps.
The anti-theft alarm ECU incorporates an RF receiver and antenna for reception of RF signals from the remote
handset for locking and alarm arming. The antenna is unterminated at one end, and for optimum performance the
antenna must not be wound around adjoining harnesses.
The anti-theft alarm ECU operates at one of two frequencies which are identified by a label on the unit. The
frequencies are:
433 MHz - Europe, Gulf States, South Africa
315 MHz - North America, South East Asia, Japan, Australia.
The anti-theft alarm ECU also incorporates an integral inertia switch. In the event of an impact of sufficient severity
to trigger the inertia switch when the ignition is on, the ECU will unlock all doors and operate the hazard warning
lamps. The ECU will remain in this condition for a pre-programmed period of 2 minutes. To reinstate CDL
functionality and to deactivate the hazard warning lamps, the ignition should be turned off and then on after the 2
minute timer has expired.
NOTE: There is a separate inertia switch for fuel cut off.
ProCarManuals.com

ELECTRICAL
5
DESCRIPTION AND OPERATION Perimetric Protection
Perimetric protection is the monitoring of each opening door or bonnet to unauthorised intrusion. The anti-theft
alarm ECU uses the door and bonnet switches described previously to determine when illegal intrusion has
occurred.
If a door/bonnet is left open when the alarm system is armed, the ECU will determine a mislock situation which is
indicated by non operation of the hazard warning lamps. If the drivers door is left open, the security LED in the
instrument pack will be illuminated for the 10 second confirmation period. If any other door or the bonnet is left
open the security LED will remain off for the 10 second confirmation period. After the confirmation period, the LED
will revert to the 1Hz deterrent flash.
If the door/bonnetis subsequently closed, the hazard warning lamps will flash to show that full perimetric protection
is now invoked. The security LED will also resume the 10 second confirmation flash.
If only the bonnet is left open, all doors will have perimetric protection and volumetric protection will also be set. If
a door is left open, the volumetric protection is suspended until that door is subsequently closed.
Volumetric Protection
The vehicle alarm system can be armed with or without volumetric protection activated. If volumetric protection is
required, the vehicle must be locked using the lock button on the remote handset. If volumetric protection is not
required, because a pet is to be left in the vehicle for instance, the vehicle must be locked using the vehicle key in
the drivers door lock.
When the vehicle is locked using the remote handset, the volumetric sensor will wait for a period of 15 seconds
before arming. This allows time for the air in the vehicle to settle and prevent incorrect activation of the alarm.
If volumetric protection is set and there is a disturbance in the vehicle, i.e., a window left open or a moving object
in the vehicle, within the 15 second period, the volumetric sensor will not activate. The sensor must detect no
disturbance for the full 15 second period before arming.
ProCarManuals.com

86ELECTRICAL
8
DESCRIPTION AND OPERATION Visual and Audible Warnings
Audible and visual warnings are dependant on market legislation. The hazard warning lamps are controlled by two
outputs from the anti-theft alarm ECU; one for the LH lamps and one for the RH lamps. To illuminate the warning
lamps the output from the ECU is at battery voltage. When the lamps are off, the output is driven to earth.
When the alarm is armed the hazard warning lamps will flash three times to indicate that the system is active.
When the alarm is triggered the sounder will operate in either a pulsed or continuous tone (dependant on market
legislation) and the hazard warning lamps will flash at 0.5 second on/off intervals for 30 seconds. The alarm
system can be triggered for up to three times in any one alarm armed cycle. When the alarm system is disarmed
confirmation will be by one single flash of the hazard warning lamps for 0.3 seconds.
If the hazard warning lamps are active when an alarm trigger is active or the alarm is armed, the visual alarm
active visual warning using the hazard warning lamps will be cancelled.
In addition to the visual and audible warnings, the security LED in the instrument pack also displays alarm system
status information.
ProCarManuals.com

86ELECTRICAL
12
DESCRIPTION AND OPERATION IMMOBILISATION SYSTEM - FROM 02MY
Engine immobilisation is available on all 2002MY engine derivatives, although it is not available in selected
markets. On Td5 models, the immobilisation system is controlled directly by the anti-theft alarm ECU. On 300Tdi
models, the immobilisation system is controlled by an engine immobilisation ECU in conjunction with the anti-theft
alarm ECU.
When immobilisation occurs on Td5 models, engine crank is disabled by the anti-theft alarm ECU breaking the
earth path for the starter relay coil and the ECM disables the fuel pump relay and the glow plug relay.
When immobilisation occurs on 300Tdi models, engine crank is disabled by the anti-theft alarm ECU breaking the
earth path for the starter relay coil and the engine immobilisation ECU disables the fuel cut-off solenoid, the starter
motor solenoid and the glow plug relay.
Two types of immobilisation are available; passive and active.
Engine Immobilised Warning Lamp
The engine immobilised warning lamp is located in the instrument pack. The lamp is used by the anti-theft alarm
ECU to show that the engine is immobilised during an attempted engine start.
The warning lamp receives a battery supply from the ignition switch position I (aux) via the passenger
compartment fusebox. The anti-theft alarm ECU controls the warning lamp. When the warning lamp is not
required, the ECU supplies a battery supply to the warning lamp. When warning lamp operation is required, the
ECU provides an earth for the bulb.
If the ignition switch is moved to the crank position, but operation of the starter motor is prohibited and the engine
immobilised warning lamp flashes, then the anti-theft alarm ECU has not received the correct code from the
remote handset and the vehicle will remain immobilised. Ensure that the remote handset is in the proximity of the
transponder coil. If the remote handset is not available or inoperative, the immobilisation system can be disarmed
using the EKA procedure outlined later in this section.
If the ignition switch is turned to the crank position III and the remote handset is not in the proximity of the
transponder coil, engine immobilisation will remain active and the warning lamp will flash to inform the driver.
ProCarManuals.com