1999 DODGE RAM engine oil

DTCs from ABS and SRS modules.
Updating Secret Key Data
Connect scan tool to Data Link Connector (DLC) below driver's\
side of instrument panel. Go to ENGINE, then MISC menu on scan tool.
Place the SKIM in SECURED ACCESS MODE by using the appropriate
Personal Identification Number (PIN) for this vehicle. PIN may be
obtained from the owner, vehicle's invoice, or from the manufacturer.
Select UPDATE THE SECRET KEY DATA. The data will be transferred from
Smart Key Immobilizer Module (SKIM) to the PCM.
NOTE: If 3 attempts are made to enter the SECURED ACCESS MODE using
the incorrect Personal Identification Number (PIN), the
SECURED ACCESS MODE will be locked out for one hour. To exit
this locked-out mode, leave ignition switch in the ON
position for one hour with all accessories turned off. It may
be necessary to monitor battery state and connect a battery
charger.
FWD CARS & FWD VANS
Transaxle Shift Quality Quick Learn Procedure (All FWD Cars
Except Avenger & Sebring Coupe, & All FWD Vans)
1) Transaxle shift quality quick learn procedure must be
performed to provide proper transaxle operation if any of the
following have been done:
* Vehicle battery was disconnected.
* Transaxle assembly was replaced.
* Transmission Control Module (TCM) was replaced.
* Solenoid assembly was replaced.
* Valve body was reconditioned or replaced.
2) Transaxle shift quality quick learn procedure must be
performed using Chrysler's Diagnostic Readout Box III (DRB-III) scan
tool. Following conditions must be met when performing transaxle shift
quality quick learn procedure:
* Brakes must be applied.
* Engine speed must be greater than 500 RPM.
* Throttle position sensor angle must be less than 3 degrees.
* Shift lever must remain in designated position until prompted
to shift to overdrive.
* Shift lever must remain in overdrive after the shift to
overdrive until scan tool indicates procedure is complete.
* Calculated oil temperature must be within 60-200
F
(16-93C).
3) Connect scan tool to Data Link Connector (DLC) below
driver's side of instrument panel. For DLC location, see appropriate
SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.
4) Go to TRANSMISSION display on scan tool. Go to
MISCELLANEOUS display on scan tool. Select QUICK LEARN PROCEDURE
display on scan tool. Follow instructions displayed on scan tool to
perform transaxle shift quality quick learn procedure. Remove scan
tool.
Transaxle Shift Quality Quick Learn Procedure (Avenger &
Sebring Coupe)
1) Transaxle shift quality quick learn procedure must be
performed to provide proper transaxle operation after replacing or
overhauling transaxle. After transaxle work is completed, clear any
Diagnostic Trouble Codes (DTCs) as necessary. Connect Chrysler's


DRIV E A XLE - F B I S EM I- F LO ATIN G
1999 D odge P ic ku p R 1500
1998-99 DRIVE AXLES
CHRY - FBI Semi-Floating Axles
Ram Pickup
IDENTIFICATION
DRIVE AXLE APPLICATION








\









\









\









\









\









\









\







Application Axle Ring Axle
Model Gear Size Ratio
Front Axle ........ 216 FBI ......... 8.50" .. 3.54, 3.92 & 4.09
Front Axle ........ 248 FBI ......... 9.75" ........ 3.54 & 4.10









\









\









\









\









\









\









\







DESCRIPTION & OPERATION
The Front Beam-Design Iron (FBI) axles is of an iron center
casting (differential housing) with axle shaft tubes extending from
both sides. The tubes are pressed in to form a one-piece axle housing
and is a semi-floating design.
Axle contains an integral carrier with hypoid-type ring gear
and pinion with semi-floating axle shafts. Load is supported by hub
bearings. Axle shafts are retained by nuts at the hub bearings. Hub
bearings are bolted to steering knuckle at outboard end of axle tube
yoke. Hub bearings are serviced as an assembly. On vehicles equipped
with Anti-Lock (ABS) brakes, a brake sensor is mounted on knuckle
assemblies, and tone rings are pressed onto axle shaft.
Differential is a one-piece design and differential pinion
mate shaft is retained with a roll pin. Differential bearing preload
and ring gear backlash is adjusted by use of shims, and pinion bearing
preload is set and maintained by use of a collapsible spacer.
Axle shaft is engaged or disengaged by an axle vacuum shift
motor. Vacuum shift motor is operated by engine vacuum and is
controlled by a switch mounted on transfer case.
AXLE RATIO & IDENTIFICATION
NOTE: Axle ratio can be identified by axle identification tag
attached to axle housing cover. See IDENTIFICATION.
LUBRICATION
CAPACITY
DRIVE AXLE CAPACITY ( 1)








\









\









\









\









\









\









\







Application Pts. (L)\
216 FBI .................................................. 4.8 (2.3)\
248 FBI .................................................. 7.6 (3.6)\
(1) - Approximate drive axle capacity listed. Lubricant level should
be 1/2" below oil filler hole in axle housing cover.









\









\









\









\









\









\









\

(1) - Approximate drive axle capacity listed. Lubricant level should
be within 1/2" below bottom of oil filler hole in axle housing
cover.
( 2) - Add container of Mopar Gear Oil Friction Modifier when
refilling.









\









\









\









\









\









\









\







FLUID TYPE
Use SAE 80W-90 or SAE 90W hypoid gear lubricant with MIL-L-
2105-B and API GL-5 ratings. Also add a container of Mopar Gear Oil
Friction Modifier when refilling.
FLUID DRAIN & REFILL
1) With lubricant of rear axle assembly at normal operating
temperature, raise and support vehicle so rear wheels are free to
rotate. Clean around axle housing cover. Loosen axle housing cover
bolts. Drain lubricant from axle housing. Remove bolts and axle
housing cover.
2) Position differential so hole in differential case faces
down. Wipe all accessible areas of axle housing. Ensure sealing
surfaces on axle housing and cover are clean. Apply a 1/4" thick bead
of silicone sealant on inside of bolt holes and along sealing surfaces
on axle housing cover.
3) Install axle housing cover, axle identification tag and
retaining bolts. Tighten bolts to 30 ft. lbs. (41 N.m). Remove oil
filler plug. Add a container of Mopar Gear Oil Friction Modifier. Fill
axle with gear lube. Install oil filler plug. Lower vehicle.
TROUBLE SHOOTING
DIFFERENTIAL NOISE
1) Ensure differential lubricant is at normal operating
temperature. Road test vehicle. Note if differential noise exists in
turns, but not during straight-ahead driving. Probable cause is
incorrect or insufficient rear axle lubricant or additive.
2) Drain and refill rear axle. See FLUID DRAIN & REFILL under
LUBRICATION. Road test vehicle and note if noise still exists, it may
be necessary to disassemble rear axle so differential can be repaired.
See RBI FULL-FLOATING AXLES article for removal of differential case.
TESTING
NOTE: Power-Lok differential can be tested without removing
differential carrier from axle housing. Either test can be
used to check drive axle.
TEST I
1) Place blocks under both front wheels. Ensure engine is off
and transmission is in Neutral. Release parking brake. Raise one rear
wheel until it is completely clear of the floor. Remove wheel. Install
Adapter (6790) to wheel studs, and tighten securely.
2) Using torque wrench on adapter, rotate axle, and record
torque required. Repeat procedure for remaining rear wheel position.
If rotational torque for either rear wheel is less than 30 ft. lbs.
(41 N.m) or greater than 200 ft. lbs. (271 N.m), Power-Lok unit must\
be replaced or repaired.

Apply multipurpose lubricant (NLGI grade 2 EP) to "U" joints
and slip joint fittings.
INSPECTION
Abnormal vibration and noise can come from many driveline
sources. Drive shaft vibration/noise increases with vehicle speed
(MPH). A vibration that occurs within a specific speed is not caused
by drive shaft imbalance. Before overhauling driveline, check for
other causes/sources of possible vibration/noise.
TIRES & WHEELS
Check tire inflation and wheel balance. Check for foreign
objects in tread, damaged tread, mismatched tread patterns or
incorrect tire sizes. Check for bent wheels.
CENTER BEARING
Tighten drive shaft center bearing mounting bolts. If bearing
insulator is deteriorated or oil-soaked, or drive shaft can be moved
up/down in support, replace center bearing support assembly.
ENGINE & TRANSMISSION MOUNTS
Tighten mounting bolts. If rubber mounts are deteriorated or
broken, replace as needed.
DRIVE SHAFT(S)
Check drive shaft(s) for missing weights, broken welds, or
for dents affecting balance. Check for undercoating, mud, snow/ice on
drive shaft(s). Clean shafts thoroughly and test drive.
"U" JOINTS
Check for foreign material lodged in joints and flange/yokes.
Check for loose "U" joint-to-flange mounting bolts. Check for worn "U"
joint needle bearings. Check for Reddish-Brown rust-dust around "U"
joint caps. Replace "U" joints if necessary.
ADJUSTMENTS
CHECKING DRIVE SHAFT PHASING
One-Piece Drive Shafts
1) Ensure "U" joint flanges on either end of drive shaft are
in same plane. See Fig. 2. Drive shafts with slip joints between yokes
often have arrows to aid in alignment. If yokes are not in same plane,
disassemble slip joint from drive shaft splines. Install slip joint
back onto drive shaft splines, aligning "U" joint yokes. Test drive.
2) Single tube type drive shaft has slip joint on outside of
"U" joint yoke (at transmission end). If one-piece tube type drive
shaft yokes are out of alignment, the drive shaft is torque-twisted.
Drive shaft must be replaced.

FLANGES
FLEX PLATES
FLUID LEVEL INDICATORS
FLUIDS AND LUBRICANTS
FLYWHEELS
FORCE MOTORS
GUIDES
HALF SHAFTS
HOSES, LINES AND TUBES
HOUSINGS (BELL, CASE, TAIL (EXTENSION) AND AUXILIARY)
INTERMEDIATE SHAFT SUPPORT BEARINGS
KEY INTERLOCK SYSTEMS
LIMITED SLIPS
LINES
LINKAGES (EXTERNAL)
LOCKING HUB ASSEMBLIES
LOCKING HUB CONTROL KNOBS
LUBRICANTS
METAL-CLAD SEALS
METALASTIC JOINTS
MODULATOR PINS
MODULATORS
MOUNTS (ENGINE, TRANSAXLE AND TRANSMISSION)
ODOMETER DRIVES (MECHANICAL)
ODOMETER HEADS (MECHANICAL)
OIL PANS
PANS
PILOT HOLES
PRESSURE PLATES
PRESSURE SWITCHES
RACES
RUBBER JOINTS (METALASTIC)
SCREENS
SEALS
SEALS (METAL-CLAD)
SELECTOR INTERLOCK SYSTEMS
SERVOS
SHIFT INTERLOCK SYSTEMS (SELECTOR AND KEY INTERLOCK SYSTEMS)
SENSORS
SIDE COVERS
SLIP YOKES
SOLENOIDS
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)
SPEEDOMETER-DRIVEN GEAR HOUSINGS
SPEEDOMETER/ODOMETER DRIVES (MECHANICAL)
SPEEDOMETER/ODOMETER HEADS (MECHANICAL)
SPEEDOMETERS AND ODOMETERS (ELECTRONIC)
SWITCHES
TONE WHEELS
TOOTHED RINGS (TONE WHEELS)
TORQUE CONVERTERS
TRANSAXLE MOUNTS
TRANSDUCERS (TRANSMISSION)
TRANSMISSION COOLERS
TRANSMISSION MOUNTS
TRANSMISSION PANS
TRANSMISSION RANGE INDICATORS (PRNDL)
TUBES
UNIVERSAL JOINTS (CARDON OR CROSS TYPE)
VACUUM CONTROLS
VACUUM HOSES
VACUUM MOTORS
VACUUM-OPERATED SWITCHES

cylinder block, above oil
pan rail.
Engine Coolant Temperature
Sensor (Diesel) On front of cylinder head,
near thermostat housing.
Engine Coolant Temperature
Sensor (3.9L) In water jacket, at front of
intake manifold.

Sensor (8.0L) On thermostat housing.
Engine Oil Pressure Sensor
(Diesel) On left side of engine, near
ECM.
Engine Oil Pressure Sensor
(3.9L) Near distributor.
Engine Oil Pressure Sensor
(5.2L) Near distributor.
Engine Oil Pressure Sensor
(5.9L) Near distributor.

Engine Oil Pressure Sensor
(8.0L) Near oil filter.
Front Wheel Speed Sensors On left and right steering
knuckles.
Heated Oxygen Sensor (HO2S)
(Downstream) (3.9L) Near outlet end of catalytic\
converter.
Heated Oxygen Sensor (HO2S)
(Downstream) (5.2L) Near outlet end of catalytic\
converter.
Heated Oxygen Sensor (HO2S)
(Left Upstream) (5.9L Heavy Duty) In left exhaust manifold
downpipe.
Heated Oxygen Sensor (HO2S)
(Left Upstream) (8.0L) In left exhaust manifold
downpipe.
Heated Oxygen Sensor (HO2S)
(Post-Catalyst) (5.9L Medium Duty) Near outlet end of catalytic\
converter.
Heated Oxygen Sensor (HO2S)
(Post-Catalyst) (8.0L California) In exhaust pipe, rear of
catalytic converter.
Heated Oxygen Sensor (HO2S)
(Pre-Catalyst) (5.9L Medium Duty) At inlet of catalytic
converter.
Heated Oxygen Sensor (HO2S)
(Pre-Catalyst) (8.0L California) At inlet of catalytic
converter.
Heated Oxygen Sensor (HO2S)
(Right Upstream) (5.9L Heavy Duty) In right exhaust manifold
downpipe.
Heated Oxygen Sensor (HO2S)
(Right Upstream) (8.0L) In right exhaust manifold
downpipe.
Heated Oxygen Sensor (HO2S)
(Upstream) (3.9L) At inlet of catalytic
converter.
Heated Oxygen Sensor (HO2S)
(Upstream) (5.2L) At inlet of catalytic
converter.