1999 DODGE RAM engine oil

Fig. 2: Identifying Oil Pan Gasket (36RH, 46RE & 47RE)
LUBRICATION
SERVICE INTERVALS
Transmission
Check transmission fluid level when performing other
underhood services. Under normal service conditions or severe service
conditions change transmission fluid, adjust bands and replace
transmission filter at specified interval. See TRANSMISSION SERVICING
INTERVALS table. Severe service conditions are conditions such as long
periods of engine idling, trailer towing, off-highway operation, snow
removal, or operating in dusty or excessively hot conditions.
TRANSMISSION SERVICING INTERVALS









\









\









\









\









\









\









\







Application Months Miles
Dakota & Durango
Normal Service ........................ 30 .............. 37,500
Severe Service ........................ ( 1) ............. 12,000

Transmission
Manufacturer recommends using Mopar ATF Plus Type 7176.
Manufacturer does not recommend using additives with transmission
fluid.
Transfer Case
Manufacturer recommends using Mopar ATF Plus Type 7176.
Power Take-Off (PTO) Adapter (Ram Pickup 2WD 2500 & 3500)
Manufacturer recommends using Mopar ATF Plus Type 7176.
FLUID CAPACITIES
TRANSMISSION REFILL CAPACITIES ( 1)








\









\









\









\









\









\









\







Application Refill Dry Fill
Qts. (L) Qts. (L\
)
Dakota & Durango
42RE, 44RE & 46RE ... ( 2) 1.5 (1.4) .... ( 3) 9.5-11.4 (9.0-10.8)
Ram Pickup
42RE ................ ( 2) 1.5 (1.4) .... ( 3) 8.5-11.0 (8.0-10.4)
46RE ................ ( 2) 1.5 (1.4) .... ( 3) 8.7-13.0 (8.2-12.3)
47RE ................ ( 2) 1.5 (1.4) .... ( 3) 8.7-16.9 (8.2-16.0)
Ram Van/Wagon
32RH & 36RH ......... ( 2) 1.5 (1.4) ...... ( 3) 8.5-9.0 (8.0-8.5)
46RE ................ ( 2) 1.5 (1.4) .. ( 3) 11.4-11.6 (10.8-11.0)
( 1) - Approximate quantity listed.
( 2) - Add fluid until fluid level is at MIN arrow mark on dipstick.
Start engine and allow engine to idle. With brakes applied,
shift transmission through all gears and back to Neutral. Add
additional fluid to bring fluid level to MIN mark on dipstick.
Recheck fluid level with transmission at normal operating
temperature. Adjust fluid level to MAX arrow mark on dipstick.
( 3) - Quantity may vary by type of oil cooler and oil cooler lines.









\









\









\









\









\









\









\







TRANSFER CASE REFILL CAPACITIES ( 1)








\









\









\









\









\









\









\







Application Pts. (L)\
Dakota & Durango
NV231 .................................................... 2.5 (1.2)\
NV242 .................................................... 2.8 (1.4)\
Ram Pickup
1500 ..................................................... 2.5 (1.2)\
2500 & 3500
2WD With Power Take-Off (PTO) Adapter ................. 9.0 (4.3\
)
5.9L Diesel & V10 ..................................... 6.5 (3.1)\
All Others ............................................ 5.0 (2.4)\
(1) - Approximate quantity listed.









\









\









\









\









\









\









\







POWER TAKE-OFF (PTO) ADAPTER REFILL CAPACITIES ( 1)








\









\









\









\









\









\









\







Application Pts. (L)\
Ram Pickup
2WD 2500 & 3500 ........................................ 4.6 (2.2)\

(1) - Approximate quantity listed.








\









\









\









\









\









\









\







DRAINING & FILLING
Transmission
1) Raise and support vehicle. Loosen oil pan bolts, allowing
fluid to drain from oil pan. Remove oil pan bolts, oil pan and gasket.
Remove oil filter bolts and oil filter from valve body.
2) Adjust kickdown band and low-reverse bands if necessary.
See KICKDOWN BAND and LOW-REVERSE BAND under ADJUSTMENTS.
3) Clean oil pan, magnet and all sealing surfaces. Install
NEW oil filter. Install and tighten oil filter bolts to specification.
See TORQUE SPECIFICATIONS.
4) Using NEW gasket, install oil pan. Install and tighten oil
pan bolts to specification. See TORQUE SPECIFICATIONS.
5) Add Mopar ATF Plus Type 7176 fluid until fluid level is at
MIN arrow mark on dipstick. Start engine and allow engine to idle.
With brakes applied, shift transmission through all gears and back to
Neutral.
6) Add additional fluid to bring fluid level to MIN mark on
dipstick. Recheck fluid level with transmission at normal operating
temperature. Adjust fluid level to MAX arrow mark on dipstick. DO NOT
overfill transmission.
Transfer Case
1) Ensure vehicle is parked on level surface. Remove transfer
case drain plug. Transfer case drain plug is located on rear of
transfer case at driver's side corner of transfer case. Allow fluid to
drain from transfer case.
2) Reinstall transfer case drain plug. Tighten transfer case
drain plug to specification. See TORQUE SPECIFICATIONS. Remove
transfer case fill plug from rear of transfer case. Transfer case fill
plug is located on rear of transfer case, just below identification
tag.
3) Fill transfer case with appropriate type of transfer case
fluid until fluid level is even with bottom of fill plug hole on
transfer case. See RECOMMENDED FLUID. Install and tighten transfer
case fill plug to specification. See TORQUE SPECIFICATIONS.
Power Take-Off (PTO) Adapter (Ram Pickup 2WD 2500 & 3500)
1) Ensure vehicle is parked on level surface. Remove drain
plug from rear of PTO adapter. See Fig. 3. Allow fluid to drain from
PTO adapter.
2) Reinstall drain plug. Tighten drain plug to specification.
See TORQUE SPECIFICATIONS. Remove fill plug from rear of PTO adapter.
See Fig. 3 .
3) Fill PTO adapter with appropriate type of fluid until
fluid level is even with bottom of fill plug hole on PTO adapter. See
RECOMMENDED FLUID. Install and tighten fill plug to specification. See
TORQUE SPECIFICATIONS.
ADJUSTMENTS
KICKDOWN BAND
1) Kickdown band is front band on transmission. Raise and
support vehicle. Loosen kickdown band adjusting screw lock nut while
preventing kickdown adjusting screw from rotating. Kickdown band
adjusting screw is located on side of transmission, near manual lever
shaft. See Fig. 4.
2) Back off kickdown band adjusting screw lock nut 5 turns.

1) Low-reverse band is rear band on transmission. Oil pan
must be removed from transmission to adjust low-reverse band. Raise
and support vehicle. Loosen oil pan bolts. Allow fluid to drain from
oil pan. Remove oil pan bolts, oil pan and gasket.
2) Loosen low-reverse band adjusting screw lock nut while
preventing low-reverse band adjusting screw from rotating. Low-reverse
band adjusting screw lock nut and low-reverse band adjusting screw are
located inside transmission, near low-reverse band. See Fig. 5.
3) Back off low-reverse band adjusting screw lock nut 5
turns. Ensure low-reverse band adjusting screw rotates freely in
transmission case.
4) Tighten low-reverse band adjusting screw to 72 INCH lbs.
(8.1 N.m). Back off low-reverse band adjusting screw specified amount
of turns. See LOW-REVERSE BAND ADJUSTMENT table. Hold low-reverse band
adjusting screw and tighten low-reverse band adjusting screw lock nut
to specification. See TORQUE SPECIFICATIONS.
LOW-REVERSE BAND ADJUSTMENT









\









\









\









\









\









\









\







Application Back Off Adjusting Screw
32RH ....................................................... 4 Turns
36H ........................................................ 2 Turns
42RE ....................................................... 4 Turns
44RE ....................................................... 4 Turns
46RE ....................................................... 2 Turns
47RE ....................................................... 3 Turns









\









\









\









\









\









\









\







5) Clean oil pan, magnet and all sealing surfaces. Using NEW
gasket, install oil pan. Install and tighten oil pan bolts to
specification. See TORQUE SPECIFICATIONS.
6) Add Mopar ATF Plus Type 7176 fluid until fluid level is at
MIN arrow mark on dipstick. Start engine and allow engine to idle.
With brakes applied, shift transmission through all gears and back to
Neutral.
7) Add additional fluid to bring fluid level to MIN mark on
dipstick. Recheck fluid level with transmission at normal operating
temperature. Adjust fluid level to MAX arrow mark on dipstick. DO NOT
overfill transmission.
Fig. 5: Locating Low-Reverse Band Adjusting Screw & Low-Reverse
Band Adjusting Screw Lock Nut
Courtesy of Chrysler Corp.
SHIFT CABLE

or bungie cord to secure transfer case shift lever in 2H position.
2) Raise and support vehicle. Loosen lock bolt at adjusting
swivel on shift rod. See Fig. 8. Ensure shift rod slides freely in
adjusting swivel. If shift rod fails to slide freely in adjusting
swivel, lubricate shift rod as necessary.
3) Ensure shift lever on transfer case is still in 2H
position. Tighten lock bolt. With all wheels off floor, start engine
and shift transfer case through all ranges to ensure proper operation.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS








\









\









\









\









\









\









\







Application Ft. Lbs. (N.m)\
Kickdown Band Adjusting Screw Lock Nut ..................... 30 (41)\
Low-Reverse Band Adjusting Screw Lock Nut .................. 25 (34)\
Oil Pan Bolt ............................................... 12 (16)\
PTO Adapter Drain Plug (Ram Pickup) ........................ 40 (54\
)
PTO Adapter Fill Plug (Ram Pickup) ......................... 40 (54\
)
Transfer Case Drain Plug ................................... 40 (54)\
Transfer Case Fill Plug .................................... 40 (54)\
INCH Lbs. (N.m)
Oil Filter Bolt ........................................... 35 (4.0)\









\









\









\









\









\









\









\

Transmission (Dakota)
Check transmission fluid level when performing other
underhood services. Under normal service conditions, change
transmission fluid at 30 months or 37,500 miles. Under severe service
conditions, change transmission fluid at 18,000 miles. Severe service
are conditions such as long periods of engine idling, trailer towing,
off-highway operation, snow removal, or operating in dusty or
excessively hot conditions.
Transmission (Ram Pickup)
Check transmission fluid level when performing other
underhood services. Fluid change service interval information is not
available from manufacturer.
Transfer Case
Check transfer case fluid level when performing other
underhood services. On Dakota and Light-Duty Pickup, change transfer
case fluid at 37,500 miles or 30 months. On Medium-Duty and Heavy-Duty
Pickup, change transfer case fluid at 36,000 miles or 36 months.
CHECKING FLUID LEVEL
Transmission (Dakota)
1) Park vehicle on level surface. Remove transmission fill
plug from side of transmission. On AX-15 transmission, transmission
fill plug is located on driver's side of transmission. On NV3500
transmission, transmission fill plug is located near front of
transmission on passenger's side of transmission.
2) On all transmissions, fluid level should even with bottom
of fill plug hole on side of transmission. Add appropriate type of
transmission fluid if necessary. See RECOMMENDED FLUID. Install and
tighten transaxle fill plug to specification. See TORQUE
SPECIFICATIONS.
Transmission (Ram Pickup)
1) Park vehicle on level surface. Remove transmission fill
plug from side of transmission. On NV3500 transmissions, transmission
fill plug is located near front of transmission on passenger's side of
transmission. On NV4500 transmissions, transmission fill plug is
located near rear of transmission on passenger's side of transmission.
2) On all transmissions, fluid level should even with bottom
of fill plug hole on side of transmission. Add appropriate type of
transmission fluid if necessary. See RECOMMENDED FLUID. Install and
tighten transaxle fill plug to specification. See TORQUE
SPECIFICATIONS.
Transfer Case
Park vehicle on level surface. Remove transfer case fill plug
from rear of transfer case. Fluid level should even with bottom of
transfer case fill plug hole on rear of transfer case. Add appropriate
type of transfer case fluid if necessary. See RECOMMENDED FLUID.
Install and tighten transfer case fill plug to specification. See
TORQUE SPECIFICATIONS.
RECOMMENDED FLUID
Transmission (Dakota)
On AX-15 transmissions, use API 75W-90 GL-3 gear oil. On
NV1500 and NV3500 transmissions, use ONLY Mopar M/T Lube Part No.
4761526.
Transmission (Ram Pickup)

3800 engines were suffering from exactly this. The point is that a
lack of detail could cause misdiagnosis.
As you might have guessed, a lab scope would not miss this.
RELATIONSHIP BETWEEN DWELL & DUTY CYCLE READINGS TABLE (1)









\









\









\









\









\









\







Dwell Meter (2) Duty Cycle Meter
1
.................................................... 1%
15 .................................................. 25%
30 .................................................. 50%
45 .................................................. 75%
60 ................................................. 100%
( 1) - These are just some examples for your understanding.
It is okay to fill in the gaps.
( 2) - Dwell meter on the six-cylinder scale.









\









\









\









\









\









\







THE TWO TYPES OF INJECTOR DRIVERS
OVERVIEW
There are two types of transistor driver circuits used to
operate electric fuel injectors: voltage controlled and current
controlled. The voltage controlled type is sometimes called a
"saturated switch" driver, while the current controlled type is
sometimes known as a "peak and hold" driver.
The basic difference between the two is the total resistance
of the injector circuit. Roughly speaking, if a particular leg in an
injector circuit has total resistance of 12 or more ohms, a voltage
control driver is used. If less than 12 ohms, a current control driver
is used.
It is a question of what is going to do the job of limiting
the current flow in the injector circuit; the inherent "high"
resistance in the injector circuit, or the transistor driver. Without
some form of control, the current flow through the injector would
cause the solenoid coil to overheat and result in a damaged injector.
VOLTAGE CONTROLLED CIRCUIT ("SATURATED SWITCH")
The voltage controlled driver inside the computer operates
much like a simple switch because it does not need to worry about
limiting current flow. Recall, this driver typically requires injector
circuits with a total leg resistance of 12 or more ohms.
The driver is either ON, closing/completing the circuit
(eliminating the voltage-drop), or OFF, opening the circuit (causing \
a
total voltage drop).
Some manufacturers call it a "saturated switch" driver. This
is because when switched ON, the driver allows the magnetic field in
the injector to build to saturation. This is the same "saturation"
property that you are familiar with for an ignition coil.
There are two ways "high" resistance can be built into an
injector circuit to limit current flow. One method uses an external
solenoid resistor and a low resistance injector, while the other uses
a high resistance injector without the solenoid resistor. See the left
side of Fig. 1.
In terms of injection opening time, the external resistor
voltage controlled circuit is somewhat faster than the voltage
controlled high resistance injector circuit. The trend, however, seems
to be moving toward use of this latter type of circuit due to its
lower cost and reliability. The ECU can compensate for slower opening

Fig. 1: Measuring Riding Height (Dakota & Durango 4WD)
Courtesy of Chrysler Corp.
JACKING & HOISTING
FLOOR JACK
CAUTION: DO NOT place jack under any part of vehicle underbody. DO NOT
attempt to raise one entire side of vehicle by placing a jack
midway between front and rear wheels, as permanent body
damage could occur. DO NOT place jack under an axle tube,
aluminum differential, steering linkage, engine or
transmission oil pan, fuel tank or front suspension arm.
Caravan, Town & Country, & Voyager
To raise front end, place floor jack under front crossmember
forward flange, inboard of lower control arm pivot. To raise rear end,
place floor jack under rear axle, next to leaf spring mount. See
Fig. 2 .