1999 DODGE RAM engine oil

Diagnostic Procedures
1) On AN and DN bodies, go to next step. On all except AN and
DN bodies, record freeze frame data. Use scan tool to read DTCs. If
DTC SPECIFIC GOOD TRIPS counter is not displayed or displayed count is
not "0", go to step 11). If DTC SPECIFIC GOOD TRIPS counter is
displayed and displayed count is "0", go to next step.
2) Turn ignition off. Disconnect PCM harness connectors.
Inspect connectors and terminals for damage. Repair as necessary. If
connectors and terminals are okay, measure resistance between
transmission temperature signal circuit at White PCM harness connector
C2 and ground circuit at Black PCM harness connector C1. If resistance
is less than 550 ohms, go to step 8). If resistance is 550 ohms or
more, go to next step.
3) If resistance is 550-2300 ohms, go to next step. If
resistance is greater than 2300 ohms, go to DTC P0713: TRANS TEMP
SENSOR VOLTAGE TOO HIGH.
4) Measure resistance of transmission temperature signal
circuit between ground and White PCM harness connector C2. If
resistance is 5 ohms or less, go to step 8). If resistance is greater
than 5 ohms, go to next step.
5) Reconnect all harness connectors. Using scan tool, read
TRANS TEMP voltage. If voltage is less than 1.5 volts, replace PCM. If
voltage is 1.5 volts or greater, go to step 7). On all other bodies,
go to next step.
6) Conditions required to set DTC P0712 are not present at
this time. DTC P0712 sets when transmission temperature sensor voltage
at PCM is less than 1.55 volts for 2.2 seconds. Possible causes are:
shorted transmission temperature sensor wiring, faulty connections,
faulty transmission temperature sensor or faulty PCM. Go to next step.
7) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
8) Disconnect transmission solenoid harness connector.
Inspect connector and terminals for damage. Repair as necessary. If
connector and terminals are okay, measure resistance between
transmission temperature signal circuit at White PCM harness connector
C2 and sensor ground circuit at Black PCM harness connector C1. If
resistance is less than 5 ohms, repair transmission temperature signal
circuit for short to ground circuit. If resistance is 5 ohms or
greater, go to next step.
9) Measure resistance between ground and transmission
temperature signal circuit at White PCM harness connector C2. If
resistance is less than 5 ohms, repair transmission temperature signal
circuit for short to ground. If resistance is 5 ohms or greater, go to
next step.
10) Reconnect transmission solenoid harness connector. Remove
transmission oil pan. Disconnect transmission pressure/temperature
sensor harness connector. Measure resistance between transmission
temperature signal circuit at White PCM harness connector C2 and
sensor ground circuit at Black PCM harness connector C1. If resistance
is less than 5 ohms, repair or replace transmission solenoid and
harness assembly. If resistance is 5 ohms or greater, go to next step.
11) Measure resistance between ground and transmission
temperature signal circuit at White PCM harness connector C2. If
resistance is less than 5 ohms, repair or replace transmission
solenoid and harness assembly. If resistance is 5 ohms or greater,
replace transmission pressure/temperature sensor.
DTC P0713: TRANS TEMP SENSOR VOLTAGE TOO HIGH
Circuit Description
Circuit is monitored continuously while key is on, and engine

2) If any DTCs listed are present, perform appropriate
test(s). See TORQUE CONVERTOR CLUTCH (TCC) TESTS table. If no DTCs a\
re
present, go to next step.
TORQUE CONVERTOR CLUTCH (TCC) TESTS









\









\









\









\









\









\









\







DTC DTC Message
P0122 (1) ................. THROTTLE POSITION SENSOR VOLTAGE TOO LOW
P0123 ( 1) ................ THROTTLE POSITION SENSOR VOLTAGE TOO HIGH
P1696 ( 1) .......................... PCM FAILURE EEPROM WRITE DENIED
P0743 ........ TORQUE CONVERTOR CLUTCH SOLENOID/TRANS RELAY CIRCUITS
( 2) ........................................................ MISFIRE
P0320 ( 1) ......................... NO CRANK REFERENCE SIGNAL AT PCM
( 1) - See appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.
( 2) - Perform appropriate misfire DTC test. See appropriate
SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.









\









\









\









\









\









\









\







3) Check transmission fluid for proper level and for any
debris. Fill or repair transmission as necessary. If fluid level and
condition are okay, go to next step.
4) Start engine. Using scan tool, perform TCC SYSTEM TEST. If
vehicle does not stall, go to step 9). If vehicle stalls, go to next
step.
5) Using scan tool, perform GOV and 3-4 SHIFT VALVE SYSTEM
TEST. Select 4th gear. If vehicle stalls, go to next step. If vehicle
does not stall, go to step 7).
6) Turn ignition off. Replace TCC solenoid. Using scan tool,
perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 4th gear. If
vehicle stalls, problem in internal. Check for blocked passage. If
vehicle does not stall, testing is complete.
7) Turn ignition off. Remove oil pump and inspect reaction
shaft, input shaft and input seal. Repair transmission as necessary.
See appropriate AUTOMATIC TRANSMISSION OVERHAUL article. If
transmission is okay, go to next step.
8) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
9) Turn ignition off. Connect a pressure gauge to
transmission cooler OUT port. Start engine. Using scan tool, perform
TCC SYSTEM TEST. If pressure increases when TCC is actuated, go to
next step. If pressure does not increase, repair leaks or blockage in
hydraulic circuit, or repair valve body as necessary.
10) Turn engine off. Remove oil pump and inspect reaction
shaft, input shaft and input seal. Repair transmission as necessary.
See appropriate AUTOMATIC TRANSMISSION OVERHAUL article. If
transmission is okay, there are no other potential causes remaining.
TCC is assumed to be defective. Replace torque converter.
DTC P0743: TORQUE CONV CLUTCH SOLENOID/TRANS RELAY CKT
NOTE: To test transmission temperature sensor, engine and
transmission temperature must be less than 85F (29C).
Circuit Description
Circuit is monitored continuously while key is on. Code sets
if voltage detected on Torque Converter Clutch (TCC) at the Powertrain\
Control Module (PCM) does not match desired voltage.
Possible Causes

switch sense circuit at O/D switch harness connector. If resistance is
less than 5 ohms, repair short to ground in O/D switch sense circuit.
If resistance is 5 ohms or greater, replace O/D off switch.
3) Conditions required to set DTC P0751 are not present at
this time. DTC P0751 sets if PCM senses O/D off switch input is held
low for 5 minutes or from time of closure or ignition on. Possible
causes are: faulty O/D OFF switch, shorted wire or faulty PCM. Inspect
all related wiring and connectors. Repair as necessary. If wiring and
connectors are okay, see INACTIVE DTC CONDITION under SELF-DIAGNOSTIC
SYSTEM. Testing is complete.
DTC P0753: TRANS 3-4 SHIFT SOLENOID/TRANS RELAY CIRCUITS
Circuit Description
Circuit is monitored continuously while key is on. Code sets
if voltage detected on 3-4 shift solenoid control circuit at the
Powertrain Control Module (PCM) does not match expected voltage.
Possible Causes
* Transmission mechanically defective.
* TPS codes set.
* Transmission 3-4 solenoid wiring harness defective.
* Transmission fluid burnt or oil pan has excessive debris.
* Shift control solenoid circuit shorted to ground.
* Solenoid and harness assembly defective.
* Transmission control relay output circuit open.
* Transmission control relay output circuit shorted to
ground.
* PCM defective.
Diagnostic Procedure (AN & DN Bodies)
1) If DTC P1765 is also set, go to DTC P1765: TRANS 12-VOLT
SUPPLY RELAY CNTRL CIRCUIT. If DTC P1765 is not set, go to next step.
2) Road test vehicle and reach a speed of 50 MPH. Depress
Overdrive (OD) switch 4 times so vehicle attempts to shift from 4th
gear to 3rd gear and back. If vehicle does not shift between 3rd and
4th gear, go to step 5). If vehicle shifts between 3rd and 4th gear,
go to next step.
3) Using scan tool, erase DTCs. Start engine. Using scan
tool, read DTCs while wiggling wiring harness between 3-4 shift
solenoid and PCM. If DTC P0753 resets, repair wiring harness as
necessary. If DTC P0753 does not reset, go to next step.
4) Using wiring diagram as a guide, inspect wiring and
connectors. Repair wiring harness as necessary. If wiring and
connectors are okay, see INACTIVE DTC CONDITION under SELF-DIAGNOSTIC
SYSTEM. Testing is complete.
5) Turn ignition off. Disconnect transmission solenoid
harness connector. Turn ignition on. Using scan tool, actuate
transmission control relay. Measure voltage between ground and
transmission relay output circuit at transmission solenoid harness
connector. If voltage does not switch from zero to greater than 10
volts, go to step 16). If voltage switches from zero to greater than
10 volts, go to next step.
6) Turn ignition off. Disconnect PCM harness connectors.
Inspect connectors and terminals for damage. Repair as necessary. If
connectors and terminals are okay, turn ignition on. Measure voltage
between ground and 3-4 shift solenoid control circuit at transmission
solenoid harness connector. If voltage is greater than 10 volts, go to
next step. If voltage is 10 volts or less, go to step 8).
7) Repair 3-4 shift solenoid control circuit for short to
voltage. Reconnect all disconnected harness connectors. Road test
vehicle and reach a speed of 50 MPH. Depress Overdrive (OD) switch 4

replace PCM and see INACTIVE DTC CONDITION under SELF-DIAGNOSTIC
SYSTEM. Testing is complete.
DTC P0783: 3-4 SHIFT SOL, NO RPM DROP @ 3-4 SHIFT
Circuit Description
Circuit is monitored continuously while key is on and engine
running. Code sets if expected RPM drop does not occur within 4
seconds of requested gear change by PCM. Test must fail 3 times to set
code.
Possible Causes
* Transmission mechanically defective.
* TPS codes set.
* Transmission 3-4 solenoid wiring harness defective.
* Transmission fluid burnt or oil pan has excessive debris.
Diagnostic Procedures
1) Using scan tool, read DTCs. On all bodies except AB and WJ
bodies, go to next step. On AB and WJ bodies, if DTC SPECIFIC GOOD
TRIPS counter is not displayed or displayed count is not "0", go to
step 6). If DTC SPECIFIC GOOD TRIPS counter is displayed and displayed
count is "0", indicating DTC still exists, go to next step.
2) If any DTCs listed are present, perform appropriate
test(s). See 3-4 SHIFT SOLENOID TESTS table. If no DTCs are present,
go to next step.
3-4 SHIFT SOLENOID TESTS









\









\









\









\









\









\









\







DTC Message Test
NO CAM SIGNAL AT PCM ..................................... ( 1) P0340
P/N SWITCH STUCK IN PARK OR IN GEAR .......................... P1899
Any Throttle Position Sensor (TPS) DTC ......................... ( 1)
TORQUE CONVERTOR CLUTCH SOLENOID/TRANS RELAY CIRCUITS ........ P0743
TRANS 12-VOLT SUPPLY RELAY CNTRL CIRCUIT ..................... P1765
TRANS 3-4 SHIFT SOLENOID/TRANS RELAY CIRCUITS ................ P0753
( 1) - See appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.









\









\









\









\









\









\









\







3) Check transmission fluid for proper level and for any
debris. Fill or repair transmission as necessary. If fluid level and
condition are okay, go to next step.
4) Connect a 0-300 psi (0-21 kg/cm
) pressure gauge to
transmission Overdrive (O/D) clutch pressure test port. Connect a
second 0-300 psi (0-21 kg/cm
) pressure gauge to transmission governor
pressure test port. See appropriate AUTOMATIC TRANSMISSION OVERHAUL
article. Ensure engine and transmission are at normal operating
temperature. With an assistant, test drive vehicle. Using scan tool,
select GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 4th gear while
monitoring pressure gauge. Governor pressure should rise to greater
than 20 psi (1.4 kg/cm
) and O/D pressure should rise to greater than
40 psi (2.8 kg/cm). If pressures are as specified, go to next step.
If pressures are not as specified, go to step 8).
5) Using wiring diagram as a guide, inspect wiring and
connectors. Repair wiring harness as necessary. If wiring and
connectors are okay, go to next step.
6) Using scan tool, erase DTCs. Start engine. Road test
vehicle at 0-55 MPH with a constant 20 percent throttle. Repeat road
test 4 times. Note if DTC P0783 resets. If DTC P0783 resets, repair
wiring harness as necessary. If DTC P0783 does not reset, go to next

step.
7) Turn engine off. Drain transmission fluid and remove oil
pan. Inspect oil pan for burnt oil and debris. Repair transmission as
necessary. See appropriate AUTOMATIC TRANSMISSION OVERHAUL article. If
transmission is okay, no problem is found at this time, see INACTIVE
DTC CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
8) Leave gauges connected. Replace 3-4 shift solenoid.
Replace transmission pan and fill with fluid. Start engine and allow
engine and transmission to reach normal operating temperature. Using
scan tool, select GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 4th gear
while monitoring pressure gauges. Governor pressure should rise to
greater than 20 psi (1.4 kg/cm
) and O/D pressure should rise to
greater than 40 psi (2.8 kg/cm). If pressures are as specified, no
problem is found at this time. Testing is complete. If pressures are
not as specified, see appropriate AUTOMATIC TRANSMISSION OVERHAUL
article, paying attention to seals and clutches related to O/D clutch.
DTC P1740: TCC OR O/D SOLENOID PERFORMANCE (BR BODY - DIESEL)
Circuit Description
Torque Converter Clutch (TCC) and overdrive clutch are tested\
when Powertrain Control Module (PCM) requests TCC engagement in 3rd
gear and overdrive. Code will set if expected RPM drop is not achieved
while attempting to engage TCC and/or overdrive. Code indicates
malfunctioning torque converter or overdrive clutch.
Possible Causes
* Fluid level or quality problem.
* Transmission wiring and connector defective.
* Transmission mechanically defective.
* Low fuel level.
* Trans temperature below 32
.
* Transfer case is in low range.
* Engine RPM trouble codes set.
* Misfire trouble code set (DTCs P0300-P0306).
* Output shaft speed trouble code set.
* PTO is engaged.
* TPS codes set (DTCs P0121-P0123).
* Torque converter defective.
Diagnostic Procedures
1) Using scan tool, read DTCs. If DTC SPECIFIC GOOD TRIPS
counter is not displayed or displayed count is not "0", go to step
16). If DTC SPECIFIC GOOD TRIPS counter is displayed and displayed
count is "0", go to next step.
2) If any DTCs listed are present, perform appropriate
test(s). See TCC OR O/D SOLENOID TESTS table. If no DTCs are present,
go to next step.
TCC OR O/D SOLENOID TESTS









\









\









\









\









\









\









\







DTC Message Test
CAMSHAFT POSITION SENSOR SIGNAL .......................... ( 1) P0341
P/N SWITCH STUCK IN PARK OR IN GEAR .......................... P1899
Any Throttle Position Sensor (TPS) DTC ......................... ( 1)
Any Misfire DTC ................................................ ( 1)
Any Engine RPM DTC ............................................. ( 1)
Any Output Shaft Speed Sensor DTC .............................. ( 1)
TRANS 12-VOLT SUPPLY RELAY CNTRL CIRCUIT ..................... P1765
TORQUE CONVERTOR CLUTCH SOLENOID/TRANS RELAY CIRCUITS ........ P0743
TRANS 3-4 SHIFT SOLENOID/TRANS RELAY CIRCUITS ................ P0753

(1) - See appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.








\









\









\









\









\









\









\







3) Ensure fuel tank is at least 1/4 full. If fuel level is
too low, correct fuel level and retest. If fuel level is okay, go to
next step.
4) Ensure transfer case is not in low range. Shift transfer
case out of low range. If transfer case is not in low range, go to
next step.
5) Ensure PTO is not engaged. Disengage PTO. If PTO is not
engaged, go to next step.
6) Ensure transmission fluid temperature is above 32
F (0C).
Warm transmission to normal operating temperature. If transmission
fluid temperature is above 32
F (0C), go to next step.
7) Turn ignition on. Using scan tool, build a custom display
with engine RPM, output shaft SPD, TCC solenoid, O/D solenoid and
throttle position. Set overdrive to off position. Road test vehicle
and reach a steady speed of 55 MPH with a minimum throttle opening
voltage of 1.15 volts for 20 seconds. Note shift patterns while
vehicle is attaining speed. If engine RPM is within 60 RPM of output
shaft speed RPM, go to next step. If engine RPM is not within 60 RPM
of output shaft speed RPM, go to step 15).
8) If output shaft speed RPM is greater than engine RPM, go
to next step. If output shaft speed RPM is equal to or less than
engine RPM, go to step 15).
9) Road test vehicle and reach a steady speed of 55 MPH and
engage overdrive. If engine RPM is 69 percent of output shaft speed,
go to step 15). If engine RPM is not 69 percent of output shaft speed,
go to next step.
10) Connect a 0-300 psi (0-21 kg/cm
) pressure gauge to
transmission Overdrive (O/D) clutch pressure test port. Connect a
second 0-300 psi (0-21 kg/cm
) pressure gauge to transmission governor
pressure test port. See appropriate AUTOMATIC TRANSMISSION OVERHAUL
article. Ensure engine and transmission are at normal operating
temperature. With an assistant, test drive vehicle. Using scan tool,
select GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 4th gear while
monitoring pressure gauge. Governor pressure should rise to greater
than 20 psi (1.4 kg/cm
) and O/D pressure should rise to greater than
40 psi (2.8 kg/cm). If pressures are as specified, go to next step.
If pressures are not as specified, go to step 13).
11) Check transmission fluid for proper level and for any
debris. Fill or repair transmission as necessary. If fluid level and
condition are okay, go to next step.
12) Drain transmission fluid and remove oil pan. If
transmission fluid is burnt or has excessive debris, repair as
necessary. If transmission fluid is okay, go to step 23).
13) Check transmission fluid for proper level and for any
debris. Fill or repair transmission as necessary. If fluid level and
condition are okay, go to next step.
14) Leave gauges connected. Replace 3-4 shift solenoid. Start
engine and allow engine and transmission to reach normal operating
temperature. Using scan tool, select GOV and 3-4 SHIFT VALVE SYSTEM
TEST. Select 4th gear while monitoring pressure gauges. Governor
pressure should rise to greater than 20 psi (1.4 kg/cm
) and O/D
pressure should rise to greater than 40 psi (2.8 kg/cm). If pressures
are as specified, testing is complete. If pressures are not as
specified, see appropriate AUTOMATIC TRANSMISSION OVERHAUL article,
paying attention to seals and clutches related to O/D clutch.
15) Check transmission fluid for proper level and for any
debris. Fill or repair transmission as necessary. If fluid level and
condition are okay, go to next step.
16) Start engine. Using scan tool, perform TCC SYSTEM TEST.

If engine stalls, go to next step. If engine does not stall, go to
step 19).
17) Using scan tool, select GOV and 3-4 SHIFT VALVE SYSTEM
TEST. Select 4th gear. If engine stalls, go to next step. If engine
does not stall, go to step 23).
18) Replace TCC solenoid. Perform GOV and 3-4 SHIFT VALVE
SYSTEM TEST. Select 4th gear. If engine stalls, repair internal
problem. Check for internally blocked passages. See appropriate
AUTOMATIC TRANSMISSION OVERHAUL article. If engine does not stall,
test is complete.
19) Turn ignition off. Remove oil pump. Inspect reaction
shaft, input shaft and input seal. If any parts are damaged, repair as
necessary and go to next step. If all parts are okay, replace torque
converter.
20) Start engine. Perform GOV and 3-4 SHIFT VALVE SYSTEM
TEST. Select 4th gear. If engine stalls, go to next step. If engine
does not stall, go to step 23).
21) Turn ignition off. Replace TCC solenoid. Start engine.
Perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 4th gear. If
engine stalls, repair internal problem. Check for internally blocked
passages. See appropriate AUTOMATIC TRANSMISSION OVERHAUL article. If
engine does not stall, go to next step.
22) Turn ignition off. Remove oil pump. Inspect reaction
shaft, input shaft and input seal. If any parts are damaged, repair as
necessary and replace torque converter. If all parts are okay, test is
complete.
23) Turn ignition off. Remove oil pump. Inspect reaction
shaft, input shaft and input seal. If any parts are damaged, repair as
necessary and replace torque converter. If all parts are okay, go to
next step.
24) Record freeze frame data to determine conditions when
code was set. Using wiring diagram as a guide, inspect wiring and
connectors. Repair wiring harness as necessary. If wiring and
connectors are okay, go to next step.
25) Using scan tool, erase DTCs. Start engine. Attempt to
duplicate data and reset code. Road test vehicle maintaining a
constant throttle opening voltage of 1.15 volts, reach a speed of 60
MPH. Repeat road test 4 times. Note if DTC P1740 resets. If DTC P1740
resets, there are no other possible causes remaining. Problem is
considered to be an intermittent problem in wiring harness connector
or wire. See INACTIVE DTC CONDITION under SELF-DIAGNOSTIC SYSTEM.
Repair wiring harness as necessary. If DTC P1740 does not reset,
testing is complete.
DTC P1756: GOV PRESS NOT EQUAL TO TARGET @ 15-20 PSI
Circuit Description
Circuit is monitored continuously while key is on and engine
running, not in Park or Neutral position or with Malfunction Indicator
Light (MIL) illuminated. Code sets if governor pressure sensor output
is not 15-30 psi (1.0-2.1 kg/cm
) when requested pressure is 20-25 psi
(1.4-1.7 kg/cm) for 2.2 seconds. Test must fail 5 times to set code.
Possible Causes
* Other transmission codes are set.
* Solenoid pack connector 5 volt supply circuit open.
* Governor pressure sensor defective.
* Transmission fluid burnt or oil pan has excessive debris.
* Governor pressure out of range.
* Transmission leaking internally.
Diagnostic Procedures

1) Using scan tool, read DTCs. On AN and DN bodies, go to
next step. On all except AN and DN bodies, if DTC SPECIFIC GOOD TRIPS
counter is not displayed or displayed count is not "0", go to step
15). If DTC SPECIFIC GOOD TRIPS counter is displayed and displayed
count is "0", go to next step.
2) Repair any other transmission related DTCs before
proceeding. See DIAGNOSTIC TROUBLE CODES (DTC) & DRB MESSAGES table.
If no other transmission related DTCs exist, go to next step.
3) Start engine. Allow engine to reach normal operating
temperature. Set parking brake, depress brake pedal and place gear
selector in "D" position. Using scan tool, read governor pressure
sensor value. If value is greater than 3 psi (.2 kg/cm
), go to next
step. If value is 3 psi (.2 kg/cm) or less, go to step 7).
4) Turn ignition off. Install a pressure gauge at
transmission governor pressure test port. See TESTING in appropriate
AUTOMATIC TRANSMISSION OVERHAUL article. Start engine. With gear
selector in "D” position, read gauge pressure. If pressure is
less than 5 psi (.3 kg/cm
), go to step 12). If pressure is 5 psi (.3
kg/cm) or greater, go to next step.
5) Turn engine off. Drain transmission fluid and remove oil
pan. Inspect oil pan for burnt oil and debris. Repair transmission as
necessary. See appropriate AUTOMATIC TRANSMISSION OVERHAUL article. If
transmission is okay, go to next step.
6) Replace governor pressure solenoid. Start engine. Read
gauge pressure. If pressure is less than 5 psi (.3 kg/cm
), testing is
complete. If pressure is 5 psi (.3 kg/cm) or greater, replace valve
body.
NOTE: Removing transmission control relay in the following step may
set other DTCs. Disregard these DTCs.
7) Place gear selector in Park. With engine still running,
remove transmission control relay. Depress brake pedal and place gear
selector in "D" position. Read governor pressure sensor value. If
value is 40-55 psi (2.8-3.9 kg/cm
), go to next step. If value is not
as specified, go to step 10).
8) Turn engine off. Install transmission control relay. Drive
vehicle at 25-30 MPH. Using scan tool, monitor governor actual
pressure and target pressure. If pressures do not stay consistently
within 5 psi (.3 kg/cm
) of each other within 3 seconds, go to next
step. If pressures stay consistently within 5 psi (.3 kg/cm) of each
other, test is complete.
9) Replace governor pressure solenoid. Drive vehicle at 25-30
MPH. Using scan tool, monitor governor actual pressure and target
pressure. If pressures do not stay consistently within 5 psi (.3
kg/cm
) of each other, repair internal transmission leakage problem.
If pressures stay consistently within 5 psi (.3 kg/cm) of each other,
testing is complete.
10) On all bodies except WJ body, go to next step. On WJ
body, turn ignition on, engine off. Measure voltage (backprobe)
between ground and 5-volt supply circuit at transmission solenoid
harness connector. If voltage is 4.5 volts or less, repair 5-volt
supply circuit for low voltage. If voltage is greater than 4.5 volts,
go to next step.
11) Turn ignition off. Install transmission control relay.
Install a pressure gauge at governor pressure test port. See TESTING
in appropriate AUTOMATIC TRANSMISSION OVERHAUL article. Start engine.
Remove transmission control relay. Depress brake pedal and place gear
selector in "D" position. Read gauge pressure. If pressure is 40-55
psi (2.8-3.9 kg/cm
), go to next step. If pressure is not as
specified, go to step 13).
12) Turn ignition off. Disconnect transmission solenoid
harness connector. Inspect connector and terminals for damage. Repair