1999 DODGE RAM battery

install, reverse removal procedure.
Removal & Installation (Ram Pickup - Front)
Blower motor resistor is located under glove box, attached to
blower motor housing. See Fig. 5. Disconnect negative battery cable.
Remove blower motor resistor connector. Remove resistor retaining
screws. Remove blower motor resistor. To install, reverse removal
procedure.
BLOWER MOTOR SWITCH (REAR)
Removal & Installation (Durango)
Disconnect negative battery cable. Pry above indentations at
outer perimeter of rear blower motor switch. Pull rear blower motor
switch and disconnect electrical connector. Remove rear blower motor
switch. To install, reverse removal procedure.
COMPRESSOR
Removal & Installation
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Disconnect
refrigerant lines and plug or cover all openings in A/C system.
2) Remove drive belt. Disconnect compressor electrical leads.
Remove compressor mounting nuts and bolts. Remove compressor. Drain
oil from compressor, and record amount of oil drained.
3) To install, reverse removal procedure. Using new
refrigerant oil, add to compressor the same amount of oil drained from
it. Evacuate and charge A/C system.
CONDENSER
NOTE: Before removing condenser, note location of radiator and
condenser air seals. If air seals are not installed properly,
A/C and engine cooling systems will not perform properly.
Removal
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Disconnect
A/C fittings at inlet and outlet of condenser. Plug or cover all
openings in A/C system.
2) On Dakota, remove bolts securing radiator and fan shroud
to inside of upper radiator crossmember. Remove top mounting bolts
securing condenser to upper crossmember. Tilt top of radiator and fan
shroud toward engine.
3) On Ram Pickup (gasoline engine), remove bolts securing
condenser upper mounting brackets to outside of upper radiator
crossmember. Tilt condenser away from engine compartment far enough to
grasp top of condenser with both hands. On Ram Pickup (diesel engine),\
remove bolts securing condenser to charge air cooler. On all models,
lift condenser assembly from vehicle.
Installation
To install, reverse removal procedure. Install new "O" rings
to fittings. Fill cooling system. Evacuate and charge A/C system.
EVAPORATOR CORE & HEATER CORE
Removal & Installation (Dakota & Durango - Front)
Remove instrument panel. See INSTRUMENT PANEL. Remove A/C-
heater assembly. See A/C-HEATER ASSEMBLY. With A/C-heater housing
removed, remove housing cover. Remove evaporator core or heater core

from housing. To install, reverse removal procedure. Install new "O"
rings to A/C fittings. Evacuate and charge A/C system.
Removal & Installation (Durango - Rear Evaporator Core)
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Remove
headliner from passenger compartment of vehicle. Remove sun visors and
sun visor arm supports.
2) Remove coat hooks, overhead assist handle and dome light.
If equipped, remove overhead console. Remove air outlet bezel from
rear A/C-heater assembly. Remove rear blower motor switch. Remove
upper liftgate opening trim. Disengage "A", "B", "C", and "D" pillar
trim as necessary to prevent trim panel interference.
3) Move second and third row seats to cargo position. Move
front seats to full recline position. Remove headliner fasteners.
Carefully bow headliner and remove through lift gate opening.
4) Disconnect "B" pillar drain hoses from "Y" fittings.
Disconnect "B" pillar refrigerant lines and plug or cover all openings
in A/C system. Remove lower A/C-heater assembly cover. Remove screws
securing refrigerant tube and retaining strap to right side of upper
housing cover. Remove evaporator core. To install, reverse removal
procedure. Install new "O" rings to A/C fittings. Evacuate and charge
A/C system.
Removal & Installation (Ram Pickup - Front)
1) Remove and disassemble A/C-heater housing. See
A/C-HEATER ASSEMBLY . Separate halves of A/C-heater housing and remove
top half. Remove evaporator or heater core from housing.
2) To install, reverse removal procedure. Install new "O"
rings to A/C fittings. Evacuate and charge A/C system. Fill cooling
system. On 5.9L diesel engine, engine is equipped with a one-way check
valve. DO NOT run engine while filling cooling system. Fill engine
with engine turned off.
INSTRUMENT PANEL
Removal & Installation (Dakota & Durango)
1) Disconnect negative battery cable. Disable air bag system.
See AIR BAG SYSTEM SAFETY article. Place front wheels in straight-
ahead position. Remove sill trim from both doorways. Remove kick panel
covers from both sides of vehicle. Remove mounting screws for hood
release handle.
2) Remove steering column trim panel and support bracket.
Remove tilt steering column lever (if equipped). Remove upper and
lower shrouds from steering column. Unplug driver's side air bag
module. Loosen multifunction switch wiring harness connector screw and
disconnect from switch. Screw will remain in connector.
3) Disconnect PRNDL cable. Disconnect shift cable from
steering column. Remove steering coupler lock pin. Remove toe plate
retaining screws. Remove steering column mounting bolts and remove
steering column from vehicle.
4) Remove screw from bulkhead wiring harness connector and
disconnect. Disconnect 2 body wiring harness connectors located next
to bulkhead connector. Disconnect 3 wiring harness connectors, from
junction block, located nearest to dash panel. Disconnect brake light
switch connector. Disconnect Rear Wheel Anti-Lock (RWAL) brake module
(if equipped), located near steering column support brackets.
5) Disconnect plastic retainer clip from parking brake
linkage rod, located at back of parking brake release handle. Remove
rod end from parking brake handle. Remove instrument panel center
support bracket. Unplug vacuum harness connector located at left end
of A/C-heater housing. Disconnect Air Bag Control Module (ACM)
connector.

6) Remove glove box. Reach through glove box opening and
disconnect antenna coaxial cable connector. Disconnect blower motor
connector located above glove box opening, near support brace for A/C-
heater housing. Disconnect radio ground strap. Loosen instrument panel
roll down bracket bolts about 2 turns, located at lower corners on
both sides of instrument panel. Remove 5 screws across top of dash
panel at base of windshield, removing center screw last.
7) Roll down instrument panel and install a temporary support
hook that is about 18" (457 mm) in length. Install hook from center
hole in instrument panel to center hole of dash panel. Pull lower
instrument panel outward until both roll down bracket bolts are in
slotted roll down position. Instrument panel should now be supported
and away from firewall.
8) Disconnect 2 door harness connectors, located on a bracket
near right end of instrument panel. Disconnect blower motor resistor.
Disconnect temperature control cable from A/C-heater housing and
remove from housing. See Fig. 5. Disconnect demister duct flexible
hose from A/C-heater housing.
9) Ensure instrument panel is free and clear for removal.
With the aid of an assistant, remove temporary support hook. Lift
instrument panel off of roll down bracket bolts and remove from
vehicle.
10) To install, reverse removal procedure. Ensure all wiring
and hoses are clear and not pinched. Tighten bolts and nuts to
specification. See TORQUE SPECIFICATIONS . Enable air bag system. See
AIR BAG SYSTEM SAFETY article.
Removal & Installation (Ram Pickup)
1) Disable air bag system. See AIR BAG SYSTEM SAFETY article.
Disconnect negative battery cable. Drain cooling system. Remove left
and right kick panel trim. Remove 5 screws and knee bolster/steering
column cover. Remove hood release and parking brake release handle
screws from lower instrument panel support. Remove 6 screws and
instrument panel support. Disconnect air bag connector at lower left
corner of instrument panel.
2) Pull PRNDL cable and twist to remove from position arm.
Push tab on bottom of cable retainer upward, then squeeze sides to
remove retainer from column. Remove tilt lever (tilt column only).
Remove both upper and lower shrouds from column. Remove lower fixed
column shroud. Loosen multifunction switch connector screw. Screw will
remain in connector.
3) Remove remaining steering column electrical connectors.
Remove air bag wiring harness from steering column wiring trough.
Remove wiring trough from steering column. Remove 3 toe plate nuts and
washers.
4) Remove 2 nuts and washers attaching steering column
bracket to instrument panel steering column support bracket. Allow
column to lower and rest on seat. Remove 2 screws from bottom of Air
Bag Control Module (ACM) cover. Remove 4 screws holding ACM to
transmission tunnel.
5) Disconnect wiring at ACM. Disconnect instrument panel left
side wiring connectors. Remove screw holding brake release to bottom
of instrument panel. Disconnect instrument panel right side wiring
connectors, which includes 2 connectors attached to A/C-heater
assembly housing, courtesy light connector, antenna cable and 2 body
connectors. Disconnect vacuum harness from A/C-heater system.
6) Remove 5 screws holding instrument panel to dash. Loosen
lower instrument panel pivot bolts. Roll instrument panel downward.
Remove instrument panel from vehicle.
7) To install, reverse removal procedure. Ensure all wiring
and hoses are clear and not pinched. Tighten bolts and nuts to
specification. See TORQUE SPECIFICATIONS . Enable air bag system. See
AIR BAG SYSTEM SAFETY article.

TEMPERATURE CONTROL CABLE R & I
Removal (Dakota & Durango)
Disconnect negative battery cable. Disconnect but DO NOT
remove instrument panel. See INSTRUMENT PANEL. Disconnect temperature
control cable from A/C-heater control panel. Disconnect temperature
control cable from flag retainer located at top of A/C-heater assembly
housing. See Fig. 7. Remove temperature control cable self-adjuster
clip and temperature control cable.
Installation
1) Before installing temperature control cable, ensure that
self-adjuster clip is positioned as indicated. See Fig. 8.
Measurements must be made with cable end bottomed against flag
retainer on A/C-heater control panel end of cable housing.
2) Measure distance between center of self-adjusting clip and
end of cable flag retainer. If distance is not as specified, adjust
self-adjuster clip. To complete installation, reverse removal
procedure.
Fig. 7: Removing Control Cable Flag From Receiver (Typical)
Courtesy of Chrysler Corp.
Fig. 8: Adjusting Temperature Control Cable (Dakota & Durango)
Courtesy of Chrysler Corp.

ORIFICE TUBE REPLACEMENT
CHRYSLER CORP.
Removal & Installation (Dakota)
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Disconnect
liquid line at condenser outlet tube. Cover open refrigerant fittings
to protect from moisture and dirt.
2) Using 2 wrenches, loosen tube fitting and separate front
half of liquid line from rear half of liquid line. Using needle nose
pliers, remove fixed orifice tube from rear half of liquid line. Note
fixed orifice tube orientation for correct installation.
3) To install, reverse removal procedure. Ensure fixed
orifice tube is positioned correctly. Evacuate, charge, and leak test
A/C system. Ensure A/C system operates properly.
NOTE: On Ram Pickup, if the fixed orifice tube is faulty or
plugged, the liquid line and orifice tube must be replaced as
an assembly.
Removal & Installation (Ram Pickup)
Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Disconnect
liquid line from evaporator inlet and condenser outlet tubes. Cover
open refrigerant fittings to protect from moisture and dirt.
Disconnect liquid line retaining clips. Remove liquid line and orifice
tube. To install, reverse removal procedure. Evacuate, charge, and
leak test A/C system. Ensure A/C system operates properly.
FORD MOTOR CO.
NOTE: Replace orifice tube whenever compressor is replaced. Fixed
orifice tube is located in the condenser-to-evaporator liquid
line.
NOTE: DO NOT use pliers to remove fixed orifice tube or twist
orifice tube in liquid line. Doing so will cause plastic
orifice tube body to break inside condenser-to-evaporator
liquid line.
Fixed Orifice Tube Replacement (Except Continental, Mustang &
Villager)
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. On Contour
and Mystique, move power steering fluid reservoir to one side without
disconnecting hoses.
2) On all models, disconnect condenser-to-evaporator
discharge (liquid) line. Remove and discard "O" rings from line. Pour
a small amount of refrigerant oil into inlet to lubricate orifice "O"
rings.
3) Insert orifice tube remover/installer into tube and turn
tool to right to engage tangs on orifice tube. See Fig. 18. Hold "T"
handle of tool and slowly tighten nut down onto discharge line to
slowly pull orifice tube out. If orifice tube breaks off when removal
is attempted, use orifice tube extractor to pull the broken section
out. See Fig. 19.
4) Ensure replacement orifice tube is fitted with "O" ring(s)\
lubricated with clean refrigerant oil. Insert tube with short end
toward evaporator, until seated. Reconnect high pressure line. On
Contour and Mystique, tighten connection to 18 ft. lbs. (24 N.m).

evaporator inlet line and "O" rings with refrigerant oil. Lubricate
orifice tube and "O" ring with refrigerant oil. Insert orifice tube
into evaporator inlet line with short screen toward condenser.
2) Tighten liquid line nut to 18 ft. lbs. (24 N.m). To
complete installation, reverse removal procedure. Evacuate, charge,
and test system for proper operation.
Removal ("F" Body)
Discharge A/C system, using approved recovery/recycling
equipment. Disconnect negative battery cable. Disconnect A/C pressure
switch connector. Use a backup wrench to hold evaporator fitting, and
loosen evaporator liquid line fitting. Remove bolt. Disconnect
evaporator liquid line. Remove and discard "O" rings. Using needle-
nose pliers, remove orifice tube from evaporator inlet line.
Installation
1) Clean evaporator line fitting with refrigerant oil. Coat
inside of inlet line and evaporator line "O" rings with refrigerant
oil. Lubricate orifice tube and "O" ring with refrigerant oil and
insert them into inlet line. Insert orifice tube into evaporator inlet
line with long screen inlet end toward condenser.
2) Tighten bolt to 12 ft. lbs. (16 N.m). Tighten evaporator
line fitting to 28 ft. lbs. (38 N.m). To complete installation,
reverse removal procedure. Evacuate, charge, and test system for
proper operation.
Removal ("J" & "N" Body)
1) Locate orifice tube. See ORIFICE TUBE LOCATION &
REMOVER/INSTALLER APPLICATION table. Discharge A/C system, using
approved recovery/recycling equipment. On "J" body, remove upper
closeout panel. On "N" body, raise and support vehicle. On all models,
disconnect condenser-to-evaporator line at condenser outlet and
discard "O" rings.
2) Disconnect condenser-to-evaporator line clip on right side
body rail, behind engine mount. Remove orifice tube using Orifice Tube
Remover/Installer (J-26549-E) or needle-nose pliers.
3) If difficulty is encountered during removal of a plugged
or restricted orifice tube, remove as much residue as possible. Using
a heat gun, carefully apply heat 1/4" from dimples on condenser inlet
line. Be careful not to overheat line.
4) If A/C pressure switch is located near orifice tube,
remove switch to protect it from heat. While heat is being applied,
grip orifice tube using orifice tube remover/installer or needle-nose
pliers. Use a turning motion along with a push-pull motion to loosen
and remove orifice tube.
Installation
1) Coat inside of condenser inlet line and "O" rings with
refrigerant oil. Lubricate orifice tube "O" ring with refrigerant oil
and insert into condenser inlet line. Insert orifice tube into
condenser inlet line with shorter screen toward evaporator.
2) Connect condenser-to-evaporator line clip on right side
body rail. Lubricate "O" rings and connect condenser inlet line.
Tighten condenser inlet line nut to 12 ft. lbs. (16 N.m). Install
closeout panel. Evacuate, charge, and test system for proper
operation.
Removal ("W" Body)
1) Locate orifice tube. See ORIFICE TUBE LOCATION &
REMOVER/INSTALLER APPLICATION table. Remove air cleaner and duct
assembly. Discharge A/C system, using approved recovery/recycling
equipment. Disconnect negative battery cable. Disconnect ABS modulator
and A/C pressure sensor/fan switch electrical connectors.

"U" Series ............ Condenser Outlet ................... N/A
(1) - In evaporator (liquid) inlet line, between service valves, above
accumulator.
( 2) - Cutlass and Malibu only.
( 3) - In evaporator (liquid) inlet line, between high-side service
valve and evaporator.









\









\









\









\









\









\









\








JEEP
NOTE: On Cherokee and Grand Cherokee, fixed orifice tube is located
in the liquid line. If the fixed orifice tube is faulty or
plugged, the liquid line and orifice tube must be replaced as
an assembly.
Removal & Installation (Cherokee & Grand Cherokee)
Disconnect battery negative cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Disconnect
liquid line retaining clips. Disconnect liquid line from evaporator
inlet and condenser outlet tubes. Cover open refrigerant fittings to
protect from moisture and dirt. Remove liquid line and orifice tube.
To install, reverse removal procedure. Evacuate, charge, and leak test
A/C system. Ensure A/C system operates properly.
Removal & Installation (Wrangler)
1) Disconnect battery negative cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Disconnect
liquid line at condenser outlet tube. Cover open refrigerant fittings
to protect from moisture and dirt.
2) Using needle nose pliers, remove fixed orifice tube from
condenser outlet tube. Note fixed orifice tube orientation for correct
installation. To install, reverse removal procedure. Ensure fixed
orifice tube is positioned correctly. Evacuate, charge, and leak test
A/C system. Ensure A/C system operates properly.
REFRIGERANT RECOVERY/RECYCLING
Refrigerant recovery/recycling equipment is used to remove
refrigerant from vehicle's A/C system without polluting atmosphere. To
remove and recycle refrigerant, ALWAYS follow instructions provided
with the refrigerant recovery/recycling equipment being used.
The removed refrigerant is filtered, dried and stored in a
tank within the recovery/recycling equipment until it is ready to be
pumped back into the vehicle's A/C system.
NOTE: Separate sets of hoses, manifold gauge set and refrigerant
recovery/recycling equipment MUST be used for R-12 and R-134a
systems. DO NOT mix R-12 and R-134a refrigerants, as their
refrigerant oils and desiccants are NOT compatible.
CHRYSLER CORP.
Manufacturer recommends using refrigerant recovery/recycling
equipment which meets SAE standard J1991 or J2210. Always follow
instructions provided with the recovery/recycling equipment being
used.
FORD MOTOR CO.
1) Connect hoses from Recovery/Recycling/Charging Center
(023-00150) to high-side and low-side service valves. See SERVICE


D - A D JU STM EN TS - D IE SEL

1999 D odge P ic ku p R 1500
1999 ENGINE PERFORMANCE
CHRY - On-Vehicle Adjustments - Trucks - Diesel
Ram Pickup
ENGINE MECHANICAL
Before performing any on-vehicle adjustments to fuel system,
ensure engine mechanical condition is okay.
VALVE CLEARANCE
NOTE: Valve clearance must be adjusted with engine temperature less
than 140F (60C).
1) Disconnect negative battery cables. Remove valve cover.
Remove fuel pump gear access cover, located at front of engine. Using
Engine Barring Tool (7471B), rotate engine to align pump gear mark
with TDC mark on gear housing cover. See Fig. 1.
Fig. 1: Rotating Engine
Courtesy of Chrysler Corp.
2) With cylinder No. 1 at TDC, check valve clearance on
proper valves. Perform STEP 1. See Fig. 2. See VALVE CLEARANCE