1999 DODGE RAM belt

\









\









\









\









\









\









\







Component Months Miles
Air Filter
Normal Service ......................... 24 ............. 30,000
Severe Service ........................ (2) ......... ( 3) 15,000
Coolant ................................. ( 4) ................ ( 4)
Drive Belt ............................... 48 ............. 60,000
Engine Oil
Normal Service ......................... 6 ................ 7500
Severe Service ........................ ( 2) ............... 3000
Engine Oil Filter
Normal Service ........................ 12 .............. 15,000
Severe Service ........................ ( 2) ............... 6000
PCV Valve (3.9L, 5.2L & 5.9L) ( 5)
Normal Service ........................ 48 .............. 60,000
Severe Service ........................ ( 2) ............. 30,000
Spark Plugs
Normal Service ........................ 24 .............. 30,000
Severe Service ........................ ( 2) ............. 30,000
Spark Plug Wires
Normal Service ........................ 48 .............. 60,000
Severe Service ........................ ( 2) ............. 60,000
Automatic Transmission Fluid,
Filter & Band Adjustment
Normal Service ........................ 30 .............. 37,500
Severe Service ........................ ( 2) ............. 12,000
Manual Transmission Fluid 3.9L
Normal Service ........................ 30 .............. 37,500
Severe Service ........................ ( 2) ............. 18,000
Transfer Case Fluid (4WD)
Normal Service ........................ 30 .............. 37,500
Severe Service ........................ ( 2) ............. 36,000
Front Differential Fluid (4WD) ( 6)
Severe Service ........................ ( 2) ............. 12,000
Rear Differential Fluid ( 6)
Severe Service ........................ ( 2) ............. 12,000
Repack Front Wheel Bearings
Normal Service ........................ 18 .............. 22,500
Severe Service ........................ ( 2) ............. 21,000
( 1) - Different interval may be required for normal and severe
service. Severe service is described as long periods of engine
idling, frequent short trip operation of less than 5 miles,
trailer towing, off-highway operation, snow removal operation,
or operating in dusty or excessively hot conditions.
( 2) - Monthly interval is not available from manufacturer.
( 3) - Inspect air filter every 15,000 miles and replace as necessary.
Replace at 30,000 miles unless previously replaced during
inspection.
( 4) - Replace coolant at 45,000 miles or 36 months whichever occurs
first. Replace coolant at 36 months regardless of mileage. After
first coolant change, replace coolant every 24 months or 30,000
miles thereafter.
( 5) - Inspect at scheduled interval and replace as necessary.
( 6) - Normal service interval is not available from manufacturer.
Manufacturer lists service schedule only under severe service
conditions.









\









\









\









\









\









\









\







REPLACEMENT INTERVALS (DURANGO) ( 1)








\









\









\









\









\









\









\







Component Months Miles

Coolant ............................ (4) ..................... ( 4)
Engine Oil
Normal Service .................... 6 ..................... 7500
Severe Service ................... ( 2) .................... 3000
Engine Oil Filter
Normal Service ................... 12 ................... 15,000
Severe Service ................... ( 2) .................... 6000
PCV Valve ( 5)
Normal Service ................... 48 ................... 60,000
Severe Service ................... ( 2) .................. 30,000
Spark Plugs
Normal Service ................... 24 ................... 30,000
Severe Service ................... ( 2) .................. 30,000
Spark Plug Wires
Normal Service ................... 48 ................... 60,000
Severe Service ................... ( 2) .................. 60,000
Automatic Transaxle Fluid,
Filter & Band Adjustment .......... ( 6) ..................... ( 6)
Rear Differential Fluid ( 7)
Severe Service ................... ( 2) .................. 12,000
Repack Front Wheel Bearings
Normal Service ................... 18 ................... 22,500
Severe Service ................... ( 2) .................. 21,000
( 1) - Different interval may be required for normal and severe
service. Severe service is described as long periods of engine
idling, frequent short trip operation of less than 5 miles,
trailer towing, or operating in dusty or excessively hot
conditions.
( 2) - Monthly interval is not available from manufacturer.
( 3) - Inspect air filter every 15,000 miles and replace as necessary.
Replace at 30,000 miles unless previously replaced during
inspection.
( 4) - Replace coolant at 45,000 miles or 36 months whichever occurs
first. Replace coolant at 36 months regardless of mileage. After
first coolant change, replace coolant every 24 months or 30,000
miles thereafter.
( 5) - Inspect at scheduled interval and replace as necessary.
( 6) - Normal service interval is not available from manufacturer.
Under severe service, change fluid, filter and adjust bands
every 12,000 miles.
( 7) - Normal service interval is not available from manufacturer.
Manufacturer lists service schedule only under severe service
conditions.









\









\









\









\









\









\









\







BELT ADJUSTMENT (Tension In Lbs. (kg) Using Belt Tension Gauge)








\









\









\









\









\









\









\







Application New Belt (1) Used Belt
Caravan
2.4L
A/C & Generator ...................... 190 (86) ...... 115 (52\
)
Power Steering ....................... 140 (64) ....... 90 (41\
)
3.0L
A/C .................................. 150 (68) ....... 80 (36\
)
Generator & Power Steering ............. ( 2) .............. ( 2)
3.3L & 3.8L ............................. ( 2) .............. ( 2)
Dakota
2.5L .................................. 200 (91) ...... 160 (73\
)
3.9L, 5.2L & 5.9L ....................... ( 2) .............. ( 2)
Durango
3.9L, 5.2L & 5.9L ....................... ( 2) .............. ( 2)

Ram Pickup, Ram Van & Ram Wagon ........... (2) .............. ( 2)
Town & Country
3.3L & 3.8L ............................. ( 2) .............. ( 2)
Voyager
2.4L
A/C & Generator ...................... 190 (86) ...... 115 (52\
)
Power Steering ....................... 140 (64) ....... 90 (41\
)
3.0L
A/C .................................. 150 (68) ....... 80 (36\
)
Generator & Power Steering ............. ( 2) .............. ( 2)
3.3L .................................... ( 2) .............. ( 2)
( 1) - Used belt is a belt that has been in service for more than 15
minutes.
( 2) - Automatic belt tensioner is used. Belt tension adjustment is not
required.









\









\









\









\









\









\









\







MECHANICAL CHECKS
ENGINE COMPRESSION
Ensure battery is fully charged. Warm engine to normal
operating temperature. Disconnect wire at ignition coil to prevent
engine from starting. Check engine compression with all spark plugs
removed and throttle wide open.
COMPRESSION SPECIFICATIONS









\









\









\









\









\









\









\







Application Specification
Compression Ratio
Caravan
2.4L ...................................................... 9.4:1
3.0L ...................................................... 8.9:1
3.3L ...................................................... 8.9:1
3.8L ...................................................... 9.6:1
Dakota & Durango ........................................... 9.1:1
Ram Pickup
3.9L, 5.2L & 5.9L (Gasoline) .............................. 9.1:1\
5.9L (Diesel) ............................................ 17.5:1\
8.0L ...................................................... 8.4:1
Ram Van & Ram Wagon ........................................ 9.1:1
Town & Country
3.3L ...................................................... 8.9:1
3.8L ...................................................... 9.6:1
Voyager
2.4L ...................................................... 9.4:1
3.0L ...................................................... 8.9:1
3.3L ...................................................... 8.9:1
Normal Compression Pressure
Caravan
2.4L ............................. 170-225 psi (11.9-15.7 kg/cm
)
3.0L ...................................... 178 psi (12.5 kg/cm)
3.3L & 3.8L ................................................. ( 1)
Dakota
2.5L .............................. 120-150 psi (8.4-10.5 kg/cm
)
3.9L, 5.2L & 5.9L ........................................... ( 1)
Durango ...................................................... ( 1)
Ram Pickup, Ram Van & Ram Wagon .............................. ( 1)
Town & Country ............................................... ( 1)
Voyager


STE ER IN G S YSTE M - P O W ER R EC IR CULA TIN G B ALL

1999 D odge P ic ku p R 1500
1998-99 STEERING
CHRY - Power Recirculating Ball - RWD Trucks
Dakota 4WD, Ram Pickup, Ram Van/Wagon
DESCRIPTION & OPERATION
The recirculating ball power steering system consists of
steering gear, steering linkage, pressure and return fluid hoses and
fittings, and a hydraulic steering pump with fluid reservoir.
The steering gear is a power assisted recirculating-ball type
that acts as a rolling thread between worm shaft and rack piston. See
Fig. 1 . When worm shaft is turned, the rack piston moves and piston
teeth mesh with sector shaft teeth, turning pitman arm, which turns
steering linkage.
The steering linkage consists of pitman arm, idler arm(s),
tie rods, center link and drag link (if equipped).
The power steering pump is a constant flow rate and
displacement, vane-type pump. Pump is connected to steering gear by
pressure and return hoses. On gasoline models, pump shaft has pressed
on belt-driven pulley.
On diesel models, power steering pump is bolted onto rear of
vacuum pump and is driven by a common shaft.
Fig. 1: Exploded View Of Saginaw Rotary Valve Power Steering Gear
Courtesy of Chrysler Corp.
TESTING

NOTE: Before testing, check fluid level, belt tension, pump pulley,
tire pressure and engine idle speed.
HYDRAULIC SYSTEM PRESSURE TEST
NOTE: Replacement fittings are required on Pressure Test Gauge(C
-3309E) for adapting to "O" ring type hose tube ends.
Idle Pressure Test
1) Remove high pressure hose at steering pump and connect a
spare hose to pump fitting. Connect opposite end of spare hose to
Pressure Test Gauge (C-3309E). Connect pressure hose from valve side
of steering gear to valve side of gauge. Valve must be installed on
outlet side of gauge. See Fig. 2.
2) Fully open shutoff valve on test gauge. With a thermometer
in fluid reservoir, start engine and warm fluid to 150-170
F (66-
77C). Turning wheels from stop-to-stop will aid in warming fluid. DO
NOT hold wheels against stop.
3) With engine at idle and gauge valve open, check initial
pressure. See POWER STEERING PUMP PRESSURE TEST SPECIFICATIONS table.
If pressure is greater than 125 psi (8.8 kg/cm

), check for restricted
hoses or crimped lines.
Fig. 2: Installing Pressure Gauge
Courtesy of Chrysler Corp.
POWER STEERING PUMP PRESSURE TEST SPECIFICATIONS
\
\
\
\
\
\
\

Application psi (kg/cm
FD)
Idle Pressure ...................................... 50-80 (3.5-5.6)\
Relief Pressure
Dakota (4WD) ........................................ 1450 (101.9\
)
Ram Pickup .......................................... 1450 (101.9)\
Ram Van/Wagon ........................................ 1400 (98.4)\
\
\
\
\
\
\
\

CAUTION: DO NOT leave shutoff valve closed more than 5 seconds, or
pump damage could result.

Relief Pressure Test
1) Close gauge shutoff valve completely 3 times. Record
highest pressure attained each time. All 3 readings must be greater
than specifications and within 50 psi (3.5 kg/cm

) of each other. See
POWER STEERING PUMP PRESSURE TEST SPECIFICATIONS table. If pressures
are not as specified, replace pump. See POWER STEERING PUMP (GASOLINE)\
or VACUUM/POWER STEERING PUMP (DIESEL) under REMOVAL & INSTALLATION.
CAUTION: DO NOT hold steering wheel against stops more than 4 seconds,
or pump damage may result.
2) Open test valve and turn steering wheel to left and right
stops. Record highest pressure attained at each stop. If output
pressures are not equal against each stop, gear is leaking internally
and must be replaced. See STEERING GEAR under REMOVAL & INSTALLATION.
Shut off engine, remove test gauge, and connect pressure hose.
LUBRICATION
CAPACITY
CAPACITY\
\
\
\
\
\
\

Models Pts. (L)\
Dakota (4WD) ............................................. 2.5 (1.2\
)
Ram Pickup & Ram Van/Wagon ............................... 2.7 (1.3)\
\
\
\
\
\
\
\

FLUID TYPE
CAUTION: DO NOT use Automatic Transmission Fluid (ATF).
Use Mopar Power Steering Fluid (4318055).
FLUID LEVEL CHECK
Check fluid level with engine cold and not running. Remove
fluid level dipstick on pump reservoir. Dipstick should indicate FULL
COLD with fluid temperature of 70-80
F (21-27C). If needed, add fluid
through dipstick opening, and recheck. DO NOT overfill.
HYDRAULIC SYSTEM BLEEDING
Fill power steering pump reservoir to specified level. Start
engine and slowly turn steering wheel to left and right, but DO NOT
contact steering stops in either direction. Stop engine. Inspect
reservoir fluid level and add fluid if necessary. Bleeding process may
have to be repeated several times to completely purge all air from
system.
ADJUSTMENTS
POWER STEERING PUMP BELT
Vehicles are equipped with dynamic tensioner. No adjustment
is required.
POWER STEERING PUMP PULLEY

After pulley installation, run the engine until warm. See
PUMP PULLEY under REMOVAL & INSTALLATION. If drive belt chirps, move
pulley outward approximately .020" (0.5 mm). If noise increases, press\
pulley inward .040" (1.0 mm). Ensure pulley does not contact mounting
bolts.
THRUST BEARING PRELOAD
NOTE: Manufacturer recommends removing steering gear from vehicle
before performing any adjustments.
1) Remove steering gear from vehicle. See STEERING GEAR under
REMOVAL & INSTALLATION. Ensure steering gear is empty of hydraulic
fluid. Rotate steering from stop-to-stop several times to drain fluid.
Loosen lock nut on adjuster plug. See Fig. 3. Using spanner wrench,
rotate adjuster plug clockwise until plug is seated in housing. Torque
will be approximately 20 ft. lbs. (27 N.m).
Fig. 3: Measuring Thrust Bearing Preload
Courtesy of Chrysler Corp.
2) Place reference mark on steering gear housing adjacent to
one hole in adjuster plug. Measure counterclockwise about 1/2" (13 mm)\

REMOVAL & INSTALLATION
CAUTION: When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may exist
until computer systems have completed a relearn cycle. See
the COMPUTER RELEARN PROCEDURES article in GENERAL
INFORMATION before disconnecting battery.
POWER STEERING PUMP (GASOLINE)
WARNING: DO NOT attempt to remove power steering pump without removing
power steering pump belt. Personal injury or pulley damage
could result.
Removal
1) Disconnect and isolate negative battery cable. To remove
serpentine belt, rotate tensioner clockwise and hold in place, slide
belt from tensioner pulley. Place drain pan under pump. Disconnect and
cap hoses.
2) Remove bracket-to-engine block bolts. Remove pump, pulley
and mounting bracket as an assembly. To allow access to pump screws,
remove pump pulley. See PUMP PULLEY. Remove bracket-to-pump screws.
Installation
To install pump, reverse removal procedure. Fill and bleed
system. See HYDRAULIC SYSTEM BLEEDING under LUBRICATION.
VACUUM/POWER STEERING PUMP (DIESEL)
Removal
1) Disconnect negative battery cable. Place drip pan under
vacuum/power steering pump. Disconnect and cap power brake booster
hose at vacuum pump and hydraulic lines at power steering pump.
Disconnect oil pressure sending unit electrical connector. Remove
sending unit from engine block and plug hole in block. Disconnect and
cap oil feed line from bottom of vacuum pump.
2) Remove vacuum/power steering pump-to-engine block nuts and
bolts, and mounting bracket. Remove upper pump bolt and remove pump.
Drain fluid from steering pump reservoir. Remove gaskets from mounting
surfaces.
CAUTION: DO NOT damage internal vacuum pump oil seal when separating
steering pump from vacuum pump. See Fig. 5.
3) Remove steering pump-to-vacuum pump bracket bolts.
Carefully slide steering pump from bracket. Remove 2 pump body
spacers. See Fig. 5.
NOTE: Steering pump housing and spacers must mate completely with
vacuum pump bracket.
Installation
1) Install 2 pump body spacers and rotate drive gear until
steering pump and vacuum pump drive splines align. See Fig. 5.
Carefully install steering pump on vacuum pump bracket to prevent
damaging oil seal.