1999 BMW 525i Workshop Manual

Downloaded from www.Manualslib.com manuals search engine
WARNING -
E39 cars are fitted with side-impact airbags in the front doors
and optional side impact
airbags in the rear doors. When
servicing doors, always disconnect the negative
(-) battery
terminal. See
721 Airbag System (SRS) for cautions and
procedures relating to the
airbag system.
Door trim panel, removing and installing
Disconnect negative (-) battery cable.
CAUTION--
Prior to disconnecting the battem read the batfew discon-
nection cautions given in
001 General Cautions and warn-
ings.
Q Open door, and remove screw (arrow) located
in air
duct.
< Pry out seat memory switch and disconnect wiring harness.

Downloaded from www.Manualslib.com manuals search engine
411-8
Doors
< Pry off plastic plug (arrow) from door handle trim and remove
screw.
4 Carefully pry out window switch panel and disconnect elec-
trical harness plugs.
< Slide door handle through trim panel

Downloaded from www.Manualslib.com manuals search engine
I
< Unclip door panel from door perimeter using a plastic trim
panel tool. Pry panel retaining clips off one at a time.
- Lift bottom of door trim panel up and away from window trim
to release clips.
- Pull door panel upwards to release center mount clip.
- Disconnect radio speaker wiring harness.
- Remove door trim panel.
< Before installing door trim panel, replace any damaged plas-
tic clips (arrows).
NOTE-
Yellow door trim clips (white arrows) at front are longer than
white door trim clips (blaclc arrows).
4 Checlt if support clip for door bracltet remains on door (ar-
row).
4 If so, remove support clip from door and replace in bracltet on
door trim panel (arrow).
- Remainder of installation is reverse of removal. Note the fol-
lowing:
Align metal retainers on window sill with openings on top
of door panel.
Checlc door-lock mechanism and window for ease of
movement.

Downloaded from www.Manualslib.com manuals search engine
411-10
/Doors
Sill trim panels
Using a trim tool, gently pry up door sill trim. Starting at A-pil-
lar, press radius of trim downwards while sliding trim forward
off trim clips. Remove clips from body using pliers. Save for
installation.
Installation is reverse of removal. Replace any damaged
plastic parts or clips.

Downloaded from www.Manualslib.com manuals search engine
41 2 Trunk Lid. Tailgate
........................... General
......................... Trunk Lid
Trunlc lid. removing and installing ........
Trunk lid. adjusting ...................
Trunk lid support strut.
removing and installing
................
Tailgate (Sport Wagon Models) .....
Tailgate. emergency release ...........
Tailgate and window strut diagram .......
Window strut removal diagram .......... 412-8
Rear window gas strut.
removing and installing
................ 412-9
Tailgate gas strut. removing and installing
............... 412-10
Tailgate. removing and installing
........ 412-1 1
Rear window. removing and installing
.... 412-12
Rear window and tailgate. alignment
..... 412-13

Downloaded from www.Manualslib.com manuals search engine
41 2-2
Trunk Lid, Tailgate
This repair group covers trunk lid and tailgate removal and in-
stallation. Also included here are replacement proceduresfor
the gas-charged support struts that hold the trunk lid or tail-
gate in the open position.
NO JE -
The body is painted at the factory after assembly. Realign-
ment of body panels may expose unpainted metal. Paint all
exposed metal once the
work is complete.
Trunk lid, removing and installing
4 Raise trunlc lid.
Open tool ltit cover and remove screws attaching tool kit to
trunlc lid (black arrows).
Disconnect tool ltit cover retaining strap from
trunk lid and
remove tool kit.
Remove insulating liner expansion rivets (white arrows).
4 Pry out moulded trim cover (arrow).

Downloaded from www.Manualslib.com manuals search engine
Trunk Lid, Tailgate
4 Pry out trunk light and disconnect electrical harness plug
connector.
- Gently pry trunk liner away from lid and remove.
4 Disconnect Wiring connectors A, B and C. Remove wiring
harness by pulling through opening in lid frame
D.
While supporting trunk lid, loosen left and right top hinge fas-
teners (arrow
A) and remove lower fasteners (arrow B).
NOTE-
Before loosening hinge bolts, mark hinge and hinge bolt lo-
cations for
reins~alla~on
Lift trunk lid straight up to remove.
Installation is reverse of removal. If necessary, align trunk lid
to body as described in
Trunk lid, adjusting.

Downloaded from www.Manualslib.com manuals search engine
/~runk Lid, Tailgate
Trunk lid, adjusting
< Trunk lid must be parallel to both side panels and should be
mounted flush with body side panels
(arrows). Lid fit toler-
ance is
rt 1 mm (0.04 in).
- Raise trunlc lid and support in open position.
Turn trunk lid detent buffers in
4 Remove trunlc strut retaining clip (arrow) and disconnect
struts.
WARNING-
Make sure to suppori trunk lid before removing struts.