Page 216 of 3115
- BODY ELECTRICALCOMBINATION METER
BE-65
2438 Author: Date:
C15 10 (D CTY SW) G dIgnition switch ON and driver door is openedBelow 1 VC15-10 (D-CTY SW) - GroundIgnition switch ON and driver door is closed10 - 14 V
C15 1 1 (IGN ) G dIgnition switch OFFBelow 1 VC15-1 1 (IGN+) - GroundIgnition switch ON10 - 14 V
C15-12 (ECU-B2) - GroundConstant10 - 14 V
C15 13 (ACC ) G dIgnition switch OFFBelow 1 VC15-13 (ACC+) - GroundIgnition switch ACC or ON10 - 14 V
C15-14 (DOOR+) - GroundConstant10 - 14 V
C15-15 (SP IN) - GroundIgnition switch ON and slowly move the wheelPulse signal is output below 1.5 V e
battery positive voltage
C15-16 (4P OUT) - GroundIgnition switch ON and slowly move the wheelPulse signal is output below 1.5 V e approx. 5 V
or below 1.5 V e battery positive voltage
If a circuit is not as specified, inspect the applicable circuit.
2. INSPECT SPEEDOMETER/ ON-VEHICLE
Using a speedometer tester, inspect the speedometer for allow-
able indication error and check the operation of the odometer.
HINT:
Tire wear and tire over or under inflation will increase the indica-
tion error.
USA (mph)CANADA (km/h)
Standard indication Allowable range Standard indication Allowable range
20 18 - 24 20 17 - 24
40 38 - 44 40 38 - 46
60 56 - 66 60 57.5 - 67
80 78 - 88 80 77 - 88
100 98 - 110 100 96 - 109
120 118 - 132 120 115 - 130
140 134 - 151.5
160 153 - 173
If error is excessive, replace the combination meter.
Page 255 of 3115
BE0FZ-19
I24653
I24654
6
I04197
BE-198
- BODY ELECTRICALHORN SYSTEM
2571 Author: Date:
2004 LAND CRUISER (RM1071U)
INSPECTION
1. INSPECT HORN SWITCH
(a) Disconnect the negative (-) terminal from the battery.
(b) Remove the left and right covers from the steering wheel.
(c) Using a torx socket wrench, loosen the 2 bolts.
(d) Pull up the horn pad and place it on the steering column,
as shown.
HINT:
Do not disconnect the connector from the horn pad.
(e) Disconnect the connector from the slip ring.
(f) Check that no continuity exists between terminal 6 of the
connector and body ground.
(g) Check that continuity exists between terminal 6 of the
connector and body ground when the horn contact plate
is pressed against the steering spoke assembly.
If continuity is not as specified, repair or replace the steering
wheel or wire harness as necessary.
(h) Install the horn pad in place and using a torx socket
wrench, torque the 2 bolts.
Torque:
7.1 N´m (72 kgf´cm, 62 in.´lbf)
(i) Install the left and right covers.
(j) Connect the negative (-) terminal to the battery.
2. INSPECT HORN OPERATION
Connect the positive (+) lead from the battery to the terminal
and negative (-) lead to the horn body and check that the horn
blows.
If operation is not as specified, replace the horn.
Page 412 of 3115
BO1KK-04
H18910
Reinforcement
Floor Brace
No. 1 BraceNo. 3 Heater to
Register Duct
Instrument PanelCenter Register
Radio With A/C Control Assembly
Front Ash Receptacle Retainer Center Lower
Cluster Finish Panel
Front Ash
Receptacle BoxLower No. 2
Panel
Glove Compartment Door
Rear Console Cup Holder Box Front
Console
Panel
Front
Console Box
Rear Console
Box
Rear Radio
Control Panel
Console Rear End Panel Combination Meter
Cluster Finish
Panel
LH Lower Panel
Lower No. 1 Panel No. 2 Heater to
Register Duct
Combination
Switch
Steering WheelSteering Wheel Pad
Front Pillar Garnish
Cowl Side Trim
Front Door Scuff Plate Front Assist Grip No. 4 Heater to
Register Duct
Front Pillar Garnish
Front Assist Grip
Cowl Side Trim
Front Door Scuff Plate
AA
A
A
BBB
C
C
C
C
CC
C
C
C
D
H
A
F
20 (204, 15)
EE
Glove Compartment
Door Damper
50 (510, 37)
BB
Rear Console BoxNo. 1 Under Cover
Console Box
Hole Cover
w/ Disc Player
Changer:
B
Column Cover
Transfer
Shift
Lever
Knob
: Specified torqueN´m (kgf´cm, ft´lbf)
H
H
H
H
I
I
EE
JJ
F
F
F
F
F
H
HH
H
H
BB
BB
HH
H
H
H
H
F
F
F
FF
D Front Console
Box bracket
- BODYINSTRUMENT PANEL
BO-81
2655 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTRUMENT PANEL
COMPONENTS
Page 420 of 3115
2 Clips
H21279
H18904
- BODYINSTRUMENT PANEL
BO-95
2669 Author: Date:
2004 LAND CRUISER (RM1071U)
28. INSTALL CLUSTER FINISH PANEL
Connect the connecter, then install the cluster finish panel.
29. INSTALL STEERING WHEEL
(See page SR-24 or SR-37)
30. INSTALL FRONT PILLAR GARNISH
(a) Install the front pillar garnish.
(b) Use the same manner described above to the other side.
31. INSTALL FRONT ASSIST GRIP
(a) Install the assist grip with the 2 screws, then install the 2
assist grip plugs.
(b) Use the same manner described above to the other side.
32. INSTALL FRONT DOOR OPENING TRIMS
33. INSTALL COWL SIDE TRIMS
34. INSTALL FRONT DOOR SCUFF PLATES
Page 423 of 3115
H18904
H21279
2 Clips
H21283
: 5 Clips
H21657
- BODYINSTRUMENT PANEL
BO-85
2659 Author: Date:
2004 LAND CRUISER (RM1071U)
8. REMOVE FRONT ASSIST GRIP
(a) Using a screwdriver, remove the assist grip plugs, then re-
move the 2 screws and assist grip.
HINT:
Tape up the screwdriver tip before use.
(b) Use the same manner described above to the other side.
9. REMOVE FRONT PILLAR GARNISH
(a) Using a screwdriver, remove the front pillar garnish.
HINT:
Tape up the screwdriver tip before use.
(b) Use the same manner described above to the other side.
10. REMOVE STEERING WHEEL
(See page SR-14 or SR-29)
11. REMOVE CLUSTER FINISH PANEL
Using a screwdriver, remove the cluster finish panel, then dis-
connect the connector.
HINT:
Tape up the screwdriver tip before use.
12. REMOVE HOOD LOCK CONTROL CABLE LEVER
AND FUEL LID CONTROL CABLE LEVER
(a) Remove the 2 screws and the hood lock control cable le-
ver.
(b) Remove the 2 screws and the fuel lid control cable lever.
13. REMOVE LOWER NO. 1 PANEL
(a) Remove the screw.
(b) Using a screwdriver, remove the lower No. 1 panel, then
disconnect the connectors.
HINT:
Tape up the screwdriver tip before use.
14. REMOVE LH LOWER PANEL
Remove the 3 bolts and the LH lower panel.
15. REMOVE COLUMN COVERS
Remove the 3 screws and the column covers.
16. REMOVE COMBINATION SWITCH
(a) Disconnect the connectors.
(b) Remove the clamp.
(c) Remove the 4 screws and the combination switch.
Page 439 of 3115
BO1J7-03
Spare Wheel
Carrier No.1 Lid
H18902
: Specified torqueN´m (kgf´cm, ft´lbf)
Rear Bumper Step Reinforcement
Extension
Mounting
Bracket
Rear Bumper CoverExtension Mounting Bracket
Reflex Reflector
4.9 (50, 43 in.´lbf)
19 (195, 14)
4.9 (50, 43 in.´lbf)
20 (204, 15)
20 (204, 15)
20 (204, 15)
Reflex Reflector
19 (195, 14)
Rear Bumper Lower Cover
12.5 (127, 11)
12.5 (127, 11)
20 (204, 15)
w/ Tow Hitch Receiver
Tow Hitch Receiver
85 (867, 63)
HINT:
REMOVAL: Remove the Tow hitch receiver
after loosening the rear bumper cover.
INSTALLATION: Install the Tow hitch receiver
after installing the rear bumper cover temporarily.
Rear Bumper Reinforcement20 (204, 15)
20 (204, 15)
85 (867, 63)
- BODYREAR BUMPER
BO-5
2579 Author: Date:
2004 LAND CRUISER (RM1071U)
REAR BUMPER
COMPONENTS
Page 480 of 3115
AB0158
SSTBattery
H04099
SST
SST
H04100
SST SST
- BODYSEAT BELT PRETENSIONER
BO-147
2721 Author: Date:
2004 LAND CRUISER (RM1071U)
HINT:
When scrapping a vehicle, activate the seat belt pretensioner
and scrap the vehicle with activated front seat outer belt still
installed.
NOTICE:
When disposing of the front seat outer belt (with seat
belt pretensioner) only, never use the customer's ve-
hicle to activate the seat belt pretensioner.
Be sure to follow the procedure given below when ac-
tivating the seat belt pretensioner.
HINT:
Have a battery ready as the power source to activate the seat
belt pretensioner.
(a) Remove the front seat outer belt (See page BO-137).
HINT:
Cut the belt near the seat belt retractor.
(b) Check functioning of SST (See step 1-(a)).
SST 09082-00700, 09082-00740
(c) Install the SST.
(1) Connect the 2 SST each other, then connect them
to the seat belt pretensioner.
SST 09082-00700, 09082-00740
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock.
(2) Place the front seat outer belt on the ground and
cover it with the disc wheel with tire.
NOTICE:
Place the front seat outer belt as shown in the illustration.
(3) Move the SST to at least 10 m (33 ft) away from the
disc wheel.
NOTICE:
Take care not to damage the SST wire harness.
Page 481 of 3115
R05181
10 m (33 ft) or more
H04101
BO-148
- BODYSEAT BELT PRETENSIONER
2722 Author: Date:
2004 LAND CRUISER (RM1071U)
(d) Activate the seat belt pretensioner.
(1) Connect the SST red clip to the battery positive (+)
terminal and black clip to the battery negative (-)
terminal.
(2) Check that no one is within 10 m (33 ft) area around
the disc wheel.
(3) Press the SST activation switch and activate the
seat belt pretensioner.
HINT:
The seat belt pretensioner operates simultaneously as the LED
of the SST activation switch lights up.
(e) Dispose of the front seat outer belt (with seat belt preten-
sioner).
CAUTION:
The front seat outer belt is very hot when the seat belt
pretensioner is activated, so leave it alone for at least
30 minutes after activation.
Use gloves and safety glasses when handling a front
seat outer belt with activated seat belt pretensioner.
Always wash your hands with water after completing
the operation.
Do not apply water, etc. to a front seat outer belt with
activated seat belt pretensioner.
(1) Remove the disc wheel and SST.
(2) Place the front seat outer belt in a vinyl bag, tie the
end tightly and dispose of it in the same way as oth-
er general parts disposal.
