Page 47 of 3115
AC1IR-04
I24822
Radiator Grill
Engine Under Cover Condenser
Liquid Tube
O-Ring Upper Bracket
N´m (kgf´cm, ft´lbf): Specified torque
Non-reusable partLower Bracket
Center Bracket Discharge Hose
O-Ring
Engine Under Cover
10 (100, 7)
10 (100, 7)
22 (225, 16)
O-Ring
Discharge Hose
Center Bracket
Lower Bracket
A/T Oil Cooler
- AIR CONDITIONINGCONDENSER
AC-69
2794 Author: Date:
2004 LAND CRUISER (RM1071U)
COMPONENTS
Page 50 of 3115
AC1IS-04
I24817
I24818
AC-70
- AIR CONDITIONINGCONDENSER
2795 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. DISCHARGE REFRIGERANT FROM REFRIGERATION
SYSTEM
HINT:
At the time of installation, refer to the following items evacuate
air from the refrigeration system and charge system with the re-
frigerant and inspect for leaks of the refrigerant.
Specified amount: 1,050 ± 50 g (37.03 ± 1.76 oz.)
2. REMOVE RADIATOR GRILL
3. REMOVE A/T AIR COOLED OIL COOLER
(See page AT-17)
4. REMOVE ENGINE UNDER COVER
5. REMOVE DISCHARGE TUBE
(a) Remove the bolt and disconnect the tube from the con-
denser.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(b) Loosen the nut and remove the tube.
Torque: 22 N´m (225 kgf´cm, 16 ft´lbf)
NOTICE:
Cap the open fittings immediately to keep moisture or dirt
out of the system.
HINT:
At the time of installation, lubricate 2 new O-rings with com-
pressor oil and install them on the tube.
6. DISCONNECT LIQUID TUBE
Remove the bolt and disconnect the tube.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
NOTICE:
Cap the open fittings immediately to keep moisture or dirt
out of the system.
HINT:
At the time of installation, lubricate a new O-ring with compres-
sor oil and install them on the tube.
Page 56 of 3115
AC1LA-03
I06764
Antenna RelayNo.1 Cooler Cover
Evaporator O-RingSuction Tube
Liquid Tube
Clamp
Instrument Panel
Evaporator Temperature SensorEvaporatorExpansion Valve
N´m (kgf´cm, in.´lbf)Grommet
: Specified torque
3.4 (35, 30)
Clamp
O-Ring
O-Ring
Non-reusable part
Tube
AC-74
- AIR CONDITIONINGFRONT A/C EVAPORATOR
2799 Author: Date:
2004 LAND CRUISER (RM1071U)
COMPONENTS
Page 60 of 3115
I06743
AC1L9-05
I06744
- AIR CONDITIONINGFRONT A/C EVAPORATOR
AC-73
2798 Author: Date:
2004 LAND CRUISER (RM1071U)
FRONT A/C EVAPORATOR
ON-VEHICLE INSPECTION
1. INSPECT FOR LEAKAGE OF REFRIGERANT
(a) Remove the glove compartment door.
(b) Remove the lower No. 2 finish panel
(See page BO-84).
(c) Remove the No. 1 cooler cover.
(1) Disconnect the connector clamp.
(2) Remove the 8 screws and No. 1 cooler cover.
(d) Using a gas leak detector, check for leaks of refrigerant.
If there is a leakage of refrigerant, check the tightening torque
at the joints or check the evaporator.
(e) Install the No. 1 cooler cover.
2. INSPECT EXPANSION VALVE
(a) Check amount of gas during refrigeration cycle.
(b) Set on manifold gauge set.
(c) Operate A/C system at ºMAX. COOLº for approx. 5 min-
utes.
(d) Check expansion valve.
Check the low pressure reading drops to 0 kPa (0
kgf/cm
2, 0 psi).
If the low pressure reading is not as specified, replace the ex-
pansion valve with the tubes.
Page 62 of 3115
AC1LB-04
I06745
I07899
- AIR CONDITIONINGFRONT A/C EVAPORATOR
AC-75
2800 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. DISCHARGE REFRIGERANT FROM REFRIGERATION
SYSTEM
HINT:
At the time of installation, evacuate air from refrigeration system
and charge the system with the refrigerant and inspect for leaks
of the refrigerant.
Specified amount: 1,050 ± 50 g (37.03 ± 1.76 oz.)
2. DISCONNECT LIQUID AND SUCTION TUBES FROM
FRONT COOLING UNIT (See page AC-24)
3. REMOVE INSTRUMENT PANEL (See page BO-84)
4. REMOVE ANTENNA RELAY
(a) Disconnect the connector.
(b) Remove the 2 screws and the antenna relay.
5. REMOVE EVAPORATOR
(a) Disconnect the connector.
(b) Disconnect the connector clamp.
(c) Remove the 8 screws and the No .1 cooler cover.
(d) Pull out the evaporator.
Page 63 of 3115
AC1K5-06
I15820
Instrument Panel
Cooling UnitLiquid Tube
Clamp Suction Tube
O-Ring
Antenna Relay
No. 2 Brace No. 1 BraceReinforcement
O-RingClamp
Grommet
Tube Expansion Valve
Cooler Case
Cooler Case Evaporator Evaporator
Temperature Sensor
No. 1 Cooler Case O-Ring
O-Ring
N´m (kgf´cm, in.´lbf) : Specified Torque
Non reusable part
3.4 (35, 30)
- AIR CONDITIONINGFRONT COOLING UNIT
AC-23
2748 Author: Date:
2004 LAND CRUISER (RM1071U)
FRONT COOLING UNIT
COMPONENTS
Page 64 of 3115
AC1K7-06
I06697
I06698
I06699
AC-26
- AIR CONDITIONINGFRONT COOLING UNIT
2751 Author: Date:
2004 LAND CRUISER (RM1071U)
DISASSEMBLY
1. REMOVE EVAPORATOR
(a) Disconnect the connector clamp.
(b) Remove the 8 screws and No. 1 cooler cover.
(c) Pull out the evaporator
HINT:
At the time of reassembly, if evaporator is replaced, add com-
pressor oil to the evaporator.
Add: 40 cc (1.4 fl.oz.)
Compressor oil: ND-OIL 8 or equivalent
2. PULL OUT EVAPORATOR TEMPERATURE SENSOR
FROM EVAPORATOR
3. REMOVE EXPANSION VALVE
(a) Remove the grommet.
(b) Pry out the packing.
HINT:
At the time of reassembly, do not reuse the packing.
(c) Using a hexagon wrench (5.0 mm, 0.20 in.), remove the
2 bolts and separate the expansion valve, tube and evap-
orator.
Torque: 3.4 N´m (35 kgf´cm, 30 in.´lbf)
NOTICE:
Cap the open fittings immediately to keep moisture or dirt
out of the system.
HINT:
At the time of reassembly, lubricate 4 new O-rings with com-
pressor oil and install them in the tube.
4. REMOVE DRAIN HOSE
Page 81 of 3115
AC1LJ-04
I06818
- AIR CONDITIONINGPOWER TRANSISTOR (for Rear Heater)
AC-83
2808 Author: Date:
2004 LAND CRUISER (RM1071U)
POWER TRANSISTOR (for Rear
Heater)
INSPECTION
1. REMOVE FRONT SEATS
2. REMOVE REAR CONSOLE BOX
3. REMOVE FRONT CONSOLE BOX COVER
4. REMOVE LOWER CENTER CLUSTER FINISH PANEL
5. REMOVE FRONT DOOR SCUFF PLATES
6. REMOVE COWL SIDE TRIMS
7. REMOVE REAR DOOR SCUFF PATES
8. REMOVE CENTER PILLAR GARNISHES
9. REMOVE POWER TRANSISTOR
(a) Slide the floor carpet backward.
(b) Disconnect the connector.
(c) Remove the 2 screws and power transistor.
10. INSPECT POWER TRANSISTOR
Check the power transistor in the same way as for ºPOWER
TRANSISTOR (For Rear Cooler)º on page AC-82.
11. INSTALL POWER TRANSISTOR
12. INSTALL CENTER PILLAR GARNISHES
13. INSTALL REAR DOOR SCUFF PATES
14. INSTALL COWL SIDE TRIMS
15. INSTALL FRONT DOOR SCUFF PLATES
16. INSTALL LOWER CENTER CLUSTER FINISH PANEL
17. INSTALL FRONT CONSOLE BOX COVER
18. INSTALL REAR CONSOLE BOX
19. INSTALL FRONT SEATS
