Page 2688 of 3115
RS0BO-08
H20940
- SUPPLEMENTAL RESTRAINT SYSTEMAIRBAG SENSOR ASSEMBLY
RS-73
2348 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
NOTICE:
Never use SRS parts from another vehicle. When re-
placing parts, replace them with new parts.
Never reuse the airbag sensor assembly involved in
a collision when the airbag has deployed.
Never repair a sensor in order to reuse it.
HINT:
For step 2 to 6, refer to page BO-91.
1. INSTALL AIRBAG SENSOR ASSEMBLY
(a) Install the airbag sensor assembly with the 3 bolts.
Torque: 17.5 N´m (178 kgf´cm, 13 ft´lbf)
(b) Connect the airbag sensor connectors.
NOTICE:
Connection of the connector is done after the sensor
assembly has been installed.
Make sure the sensor assembly is installed with the
specified torque.
If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.
When installing the sensor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.
After installing, shake the sensor assembly to check
that there is no looseness.
2. INSTALL CENTER LOWER INSTRUMENT CLUSTER
FINISH PANEL ASSEMBLY
3. INSTALL FRONT CONSOLE BOX
4. INSTALL REAR CONSOLE BOX WITH CONSOLE
REAR END PANEL
5. INSTALL UPPER CONSOLE PANEL
6. INSTALL TRANSFER SHIFT LEVER KNOB
7. INSTALL FRONT SEAT (See page BO-1 17)
8. INSPECT SRS WARNING LIGHT (See page DI-692)
Page 2689 of 3115
RS0BL-08
H20940
RS-70
- SUPPLEMENTAL RESTRAINT SYSTEMAIRBAG SENSOR ASSEMBLY
2345 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
NOTICE:
Do not open the cover or the case of the ECU and various
electrical devices unless absolutely necessary.
(If the IC terminals are touched, the IC may be destroyed by
static electricity.)
HINT:
For step 2 to 6, refer to page BO-84.
1. REMOVE FRONT SEAT (See page BO-105)
2. REMOVE TRANSFER SHIFT LEVER KNOB
3. REMOVE UPPER CONSOLE PANEL
4. REMOVE REAR CONSOLE BOX WITH CONSOLE
REAR END PANEL
5. REMOVE FRONT CONSOLE BOX
6. REMOVE CENTER LOWER CLUSTER FINISH PANEL
ASSEMBLY
7. REMOVE AIRBAG SENSOR ASSEMBLY
(a) Disconnect the airbag sensor connectors.
NOTICE:
Disconnect the connectors with the airbag sensor assem-
bly installed.
(b) Remove the 3 bolts and the airbag sensor assembly.
Page 2690 of 3115
RS0BN-01
RS-72
- SUPPLEMENTAL RESTRAINT SYSTEMAIRBAG SENSOR ASSEMBLY
2347 Author: Date:
2004 LAND CRUISER (RM1071U)
REPLACEMENT
REPLACEMENT REQUIREMENTS
In the following cases, replace the airbag sensor assembly.
If the SRS has been deployed in a collision.
If the airbag sensor assembly has been found to be faulty in troubleshooting.
If the airbag sensor assembly has been dropped.
CAUTION:
For removal and installation of the airbag sensor assembly, see page RS-70 and RS-73. Be sure to
follow the correct procedure.
Page 2702 of 3115
RS0SH-04
H20947N´m (kgf´cm, ft´lbf) : Specified torque
17.5 (178, 13)
42 (428, 31)
Striker Plate
Rear Mat Set Plate
Quarter Trim Panel
Rear Door Scuff PlateRear No. 2 Seat Rear Door Opening Trim Weatherstrip
Rear Seat Belt Anchor
Curtain Shield Airbag Sensor Assembly
Striker Plate
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG SENSOR ASSEMBLY
RS-85
2360 Author: Date:
2004 LAND CRUISER (RM1071U)
CURTAIN SHIELD AIRBAG SENSOR ASSEMBLY
COMPONENTS
Page 2703 of 3115
RS0SJ-03
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG SENSOR ASSEMBLY
RS-87
2362 Author: Date:
2004 LAND CRUISER (RM1071U)
INSPECTION
1. Vehicle not involved in collision:
INSPECT SUPPLEMENTAL RESTRAINT SYSTEM
Do a diagnostic system check (See page DI-692).
2. Vehicle involved in collision and airbag is not deployed:
INSPECT SUPPLEMENTAL RESTRAINT SYSTEM
Do a diagnostic system check (See page DI-692).
3. Vehicle involved in collision and airbag is deployed:
INSPECT SUPPLEMENTAL RESTRAINT SYSTEM
Replace the curtain shield airbag sensor assembly (See page RS-85).
Page 2704 of 3115
RS0SL-04
H20948
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG SENSOR ASSEMBLY
RS-89
2364 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
NOTICE:
Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.
Never reuse the curtain shield airbag sensor assem-
bly involved in a collision when the airbag has
deployed.
Never repair a sensor in order to reuse it.
HINT:
For step 2 to 8, refer to page BO-101.
1. INSTALL CURTAIN SHIELD AIRBAG SENSOR AS-
SEMBLY
(a) Install the curtain shield airbag sensor assembly with the
2 bolts.
Torque: 17.5 N´m (178 kgf´cm, 13 ft´lbf)
(b) Connect the connector.
NOTICE:
Connection of the connector is done after the sensor
assembly has been installed.
Make sure that the sensor assembly is installed with
the specified torque.
If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.
When installing the sensor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.
After installation, shake the sensor assembly to
check that there is no looseness.
2. INSTALL QUARTER TRIM PANEL
3. INSTALL STRIKER PLATES
4. INSTALL REAR NO. 2 SEAT
5. INSTALL REAR MAT SET PLATE
6. INSTALL REAR SEAT BELT ANCHOR
7. INSTALL REAR DOOR OPENING TRIM
8. INSTALL REAR DOOR SCUFF PLATE
9. INSPECT SRS WARNING LIGHT (See page DI-692)
Page 2705 of 3115
RS0SI-04
H20948
RS-86
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG SENSOR ASSEMBLY
2361 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
NOTICE:
Do not open the cover or the case of the ECU and vari-
ous electrical devices unless absolutely necessary.
(If the IC terminals are touched, the IC may be de-
stroyed by static electricity.)
If the wiring connector of the SRS is disconnected
and the ignition switch is at ON position, DTCs will be
recorded.
HINT:
For the step 1 to 7, refer to page BO-97.
1. REMOVE REAR DOOR SCUFF PLATE
2. REMOVE REAR DOOR OPENING TRIM
3. REMOVE REAR SEAT BELT ANCHOR
4. REMOVE REAR MAT SET PLATE
5. REMOVE REAR NO. 2 SEAT
6. REMOVE STRIKER PLATES
7. REMOVE QUARTER TRIM PANEL
8. REMOVE CURTAIN SHIELD AIRBAG SENSOR AS-
SEMBLY
(a) Disconnect the connector.
NOTICE:
Disconnect the connector with the sensor assembly
installed.
(b) Remove the 2 bolts and curtain shield airbag sensor as-
sembly.
Page 2706 of 3115
RS0SK-02
RS-88
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG SENSOR ASSEMBLY
2363 Author: Date:
2004 LAND CRUISER (RM1071U)
REPLACEMENT
REPLACEMENT REQUIREMENTS
In the following cases, replace the curtain shield airbag sensor assembly.
If the curtain shield airbag sensor assembly has been deployed in a collision.
If the curtain shield airbag sensor assembly has been found to be faulty in troubleshooting.
If the curtain shield airbag sensor assembly has been dropped.
CAUTION:
For removal and installation of the curtain shield airbag sensor assembly, see page RS-86 and
RS-89. Be sure to follow the correct procedure.
