Page 1547 of 3115
AB0119H10600 H01017
H01071H16278H16626
Side Squib LH
Airbag
Sensor
Assembly
SFL+SFL-
" u
DLC3ON
CGTCDTC B0117/45 Floor No. 1 Wire
DI-766
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
959 Author: Date:
2004 LAND CRUISER (RM1071U)
3 Check airbag sensor assembly.
PREPARATION:
(a) Connect the connector to the airbag sensor assembly.
(b) Using a service wire, connect SFL+ and SFL- of the floor
No. 1 wire connector on the side airbag assembly LH
(side squib LH) side.
(c) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0117/45 is not output.
HINT:
Codes other than code B0117/45 may be output at this time, but
they are not relevant to this check.
NG Replace airbag sensor assembly.
OK
Page 1548 of 3115
H10600 H01018 AB0119
H01071H11030
"u
TCAirbag
Sensor
Assembly Side Squib LH
DTC B0117/45 ON
DLC3
CG
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-767
960 Author: Date:
2004 LAND CRUISER (RM1071U)
4 Check side squib LH.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Connect the side airbag assembly LH (side squib LH)
connector.
(d) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0117/45 is not output.
HINT:
Codes other than code B0117/45 may be output at this time, but
they are not relevant to this check.
NG Replace side airbag assembly LH
(side squib LH).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check. If the malfunctioning part can not be
detected by the simulation method, replace all SRS components including the wire harness.
Page 1549 of 3115
H01016AB0119
H16277H16627
Side Squib LHAirbag
Sensor
Assembly
SFL+
(-)(+)
ON
Floor No. 1 Wire
DI-768
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
961 Author: Date:
2004 LAND CRUISER (RM1071U)
DTC B0118/46 Short in Side Squib LH Circuit (to B+)
CIRCUIT DESCRIPTION
The side squib LH circuit consists of the airbag sensor assembly and the side airbag assembly LH.
It causes the SRS to deploy when the SRS deployment conditions are satisfied.
For details of the function of each component, see OPERATION on page RS-3.
DTC B0118/46 is recorded when a B+ short is detected in the side squib LH circuit.
DTC No.DTC Detecting ConditionTrouble Area
B0118/46
Short in side squib LH circuit (to B+)
Side squib LH malfunction
Airbag sensor assembly malfunctionSide airbag assembly LH (Side squib LH)
Airbag sensor assembly
Floor No. 1 wire
HINT:
DTC B0118/46 is indicated only for the vehicle equipped with the side airbag.
WIRING DIAGRAM
See page DI-692.
INSPECTION PROCEDURE
1 Prepare for inspection (See step 1 on page DI-692).
2 Check floor No. 1 wire (side squib LH circuit).
CHECK:
(a) Turn the ignition switch to ON.
(b) Measure the voltage between the body ground and SFL+
of the floor No. 1 wire connector on the side airbag assem-
bly LH (side squib LH) side.
OK:
Voltage: Below 1 V
NG Repair or replace floor No. 1 wire.
OK
DI6PI-21
Page 1550 of 3115
AB0119H01017
H01072 H10600H16278H16628
Side Squib LH
Airbag
Sensor
Assembly
SFL+
CG
TCDTC B0118/46
" u
SFL-
ON
DLC3Floor No. 1 Wire
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-769
962 Author: Date:
2004 LAND CRUISER (RM1071U)
3 Check airbag sensor assembly.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Connect the connector to the airbag sensor assembly.
(d) Using a service wire, connect SFL+ and SFL- of the floor
No. 1 wire connector on the side airbag assembly LH
(side squib LH) side.
(e) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0118/46 is not output.
HINT:
Codes other than code B0118/46 may be output at this time, but
they are not relevant to this check.
NG Replace airbag sensor assembly.
OK
Page 1551 of 3115
H01018AB0119H01072H10600H13118
"uAirbag
Sensor
Assembly Side Squib LH
DTC B0118/46 ON
DLC3
TC CG
DI-770
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
963 Author: Date:
2004 LAND CRUISER (RM1071U)
4 Check side squib LH.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Connect the side airbag assembly LH (side squib LH)
connector.
(d) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0118/46 is not output.
HINT:
Codes other than code B0118/46 may be output at this time, but
they are not relevant to this check.
NG Replace side airbag assembly LH
(side squib LH).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check. If the malfunctioning part can not be
detected by the simulation method, replace all SRS components including the wire harness.
Page 1552 of 3115
H21792
B5 Buckle Switch LH
Airbag Sensor Assembly
BM2
1G19
C25LBE+
C2511
G
(*1) (*2) 3
*1: w/ Side Airbag
*2: w/o Side Airbag
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-771
964 Author: Date:
2004 LAND CRUISER (RM1071U)
DTC B0126/B0127/27 Seat Belt Buckle Switch LH
Malfunction
CIRCUIT DESCRIPTION
The seat belt buckle switch LH malfunction circuit consists of the airbag sensor assembly and the front seat
inner belt LH (seat belt buckle switch LH).
For details of the function of each component, see OPERATION on page RS-3.
DTC B0126/B0127/27 is recorded when a malfunction is detected in the seat belt buckle switch LH circuit.
DTC No.DTC Detecting ConditionTrouble Area
B0126/B0127/27Seat belt buckle switch LH circuit malfunction
Front seat inner belt LH (Seat belt buckle switch LH)
Airbag sensor assembly
Floor No. 1 wire
Front seat wire LH
WIRING DIAGRAM
DIB3R-01
Page 1553 of 3115
H20477H16861H21676
Seat Belt Buckle
Switch LHAirbag
Sensor
Assembly
w/o Side Airbag:
Airbag Sensor
Assemblyw/ Side Airbag:
Airbag Sensor
Assembly
LBE+
(+) (-)
(+) (-)LBE+
H20565AB0119H16860H21677
Seat Belt Buckle
Switch LHAirbag
Sensor
Assembly
w/o Side Airbag:
Airbag Sensor
Assemblyw/ Side Airbag:
Airbag Sensor
Assembly
LBE+
(+) (-)
(+) (-)LBE+
ON
DI-772
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
965 Author: Date:
2004 LAND CRUISER (RM1071U)
INSPECTION PROCEDURE
1 Prepare for inspection (See step 1 on page DI-692).
2 Check wire harness (to ground).
CHECK:
Measure the resistance between the body ground and LBE+ of
the connector on the airbag sensor assembly side between the
front seat inner belt LH (seat belt buckle switch LH) and the air-
bag sensor assembly.
OK:
Resistance: 1 MW or Higher
NG Go to step 7.
OK
3 Check wire harness (to B+).
PREPARATION:
Connect the negative (-) terminal cable to the battery, and wait
at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON.
(b) Measure the voltage between the body ground and LBE+
of the connector on the airbag sensor assembly side be-
tween the front seat inner belt LH (seat belt buckle switch
LH) and the airbag sensor assembly.
OK:
Voltage: Below 1 V
NG Go to step 8.
OK
Page 1554 of 3115
H20477H16861H21678
Seat Belt Buckle
Switch LHAirbag
Sensor
Assembly
w/ Side Airbag:
Airbag Sensor
Assembly w/o Side Airbag:
Airbag Sensor
Assembly
LBE+
(+)(-)
(+) (-)LBE+
H20477H16861H21678
Airbag
Sensor
Assembly
w/ Side Airbag:
Airbag Sensor
Assemblyw/o Side Airbag:
Airbag Sensor
Assembly
LBE+
(+)(-)
(+) (-)LBE+
Seat Belt
Buckle
Switch LH
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-773
966 Author: Date:
2004 LAND CRUISER (RM1071U)
4 Check front seat inner belt LH.
PREPARATION:
(a) Connect the connector of the front seat inner belt LH (seat
belt buckle switch LH).
(b) Unlock the seat belt for the driver's seat.
CHECK:
Measure the resistance between the body ground and LBE+ of
the connector on the airbag sensor assembly side between the
front seat inner belt LH (seat belt buckle switch LH) and the air-
bag sensor assembly.
OK:
Resistance: 1 kW - 1.6 kW
NG Replace front seat inner belt LH.
OK
5 Check front seat inner belt LH.
PREPARATION:
Lock the seat belt for the driver's seat.
CHECK:
Measure the resistance between the body ground and LBE+ of
the connector on the airbag sensor assembly side between the
front seat inner belt LH (seat belt buckle switch LH) and the air-
bag sensor assembly.
OK:
Resistance: 100 W - 500 W
NG Replace front seat inner belt LH.
OK
