Page 1084 of 3115
DI3CH-17
I25003
E5E6E7E8E9 DI-990
- DIAGNOSTICSCRUISE CONTROL SYSTEM
1183 Author: Date:
2004 LAND CRUISER (RM1071U)
TERMINALS OF ECM
Symbols (Terminals No.)Wiring ColorConditionSpecified condition
STP e E1GWBRDepress brake pedal10 - 16 VSTP e E1
(E8-19 e E7-1)G-W e BRRelease brake pedalBelow 1 V
Ignition switch ON10 - 16 V
Ignition switch ON
CANCEL switch hold ON3.6 - 7.2 V
Ignition switch ON
-/SET switch hold ON2.1 - 4.9 V
CCS e E1
(E8-24 e E7-1)L e BRIgnition switch ON
+/RES switch hold ON0.7 - 2.6 V
Ignition switch ONBl 1VIgnition switch ON
Main switch OFFBelow 1 V
Ignition switch ON10 14 VIgnition switch ON
Main switch ON10 - 14 V
ST1- e E1RGBRDepress brake pedalBelow 1 VST1 e E1
(E8-12 e E7-1)R-G e BRRelease brake pedal10 - 14 V
Page 1222 of 3115
- DIAGNOSTICSENGINE
DI-173
366 Author: Date:
2004 LAND CRUISER (RM1071U)
Be sure to check the value on the misfire counter after the repair.
1 Are there any other codes (besides DTC P0300, P0301, P0302, P0303, P0304
P0305, P0306, P0307 or P0308) being output?
PREPARATION:
(a) Connect the hand-held tester or the OBD II scan tool to the DLC3.
(b) Turn the ignition switch ON and push the hand-held tester or OBD II scan tool main switch ON.
(c) When using hand-held tester, enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTC using hand-held tester or the OBD II scan tool.
RESULT:
Display (DTC Output)Proceed to
ºP0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or
P0308ºA
ºP0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or
P0308º and other DTCsB
HINT:
If any other codes besides ºP0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308º are
output, perform the troubleshooting for those DTC.
B Go to relevant DTC chart (See page DI-36).
A
2 Check wire harness, connector and vacuum hose in engine room.
CHECK:
(a) Check the connection conditions of the wire harness and connector.
(b) Check for the disconnection, piping and brake of the vacuum hose.
NG Repair or replace, then confirm that there is no
misfire (See confirmation driving pattern).
OK
3 Check connection of PCV piping.
NG Repair or replace PCV piping.
OK
Page 1327 of 3115
DI-278
- DIAGNOSTICSENGINE
471 Author: Date:
2004 LAND CRUISER (RM1071U)
DTC P0504 Brake Switch ºAº/ºBº Correlation
CIRCUIT DESCRIPTION
In addition to turning on the stop lamps, the stop lamp switch signals are used for a variety of engine, trans-
mission, and suspension functions as well as being an input for diagnostic checks. It is important that the
switch operates properly, therefore this switch is designed with two complementary signal outputs: STP and
ST1-. The ECM analyzes these signal outputs to detect malfunctions in the stop lamp switch.
HINT:
Normal condition is as shown in the table.
SignalBrake pedal releasedIn transitionBrake pedal depressed
STPOFFONON
ST1-ONONOFF
DTC No.DTC Detection ConditionTrouble Area
P0504
Conditions (a), (b) and (c) continue for 0.5 sec. or more:
(a) Ignition switch ON
(b) Brake pedal released
(c) STP signal is OFF when the ST1- signal is OFFShort in stop lamp switch signal circuit
Stop lamp fuse
Stop lamp switch
ECM
DIC2K-01
Page 1329 of 3115
DI-280
- DIAGNOSTICSENGINE
473 Author: Date:
2004 LAND CRUISER (RM1071U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester or the OBD II scan tool. Freeze frame data records the
engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help deter-
mine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean
or rich, as well as other data from the time when a malfunction occurred.
Hand-held tester:
1 Check operation of stop light.
CHECK:
Check if the stop lights come on and go off normally when the brake pedal is operated and released.
NG Check and repair stop light circuit.
OK
2 Check STOP fuse.
PREPARATION:
Remove the STOP fuse from the cowl side J/B LH.
CHECK:
Check the continuity of the STOP fuse.
OK:
Continuity
NG Check for short in all harness and components
connected to STOP fuse.
OK
3 Check stop light switch (See page BE-50).
NG Replace stop light switch.
OK
Page 1330 of 3115
A19642
Brake Pedal
DepressedBrake Pedal
Release ON
() ()
ST1-(+)E8
E7
E1 (-)
- DIAGNOSTICSENGINE
DI-281
474 Author: Date:
2004 LAND CRUISER (RM1071U)
4 Check STP signal and ST1- voltage.
PREPARATION:
(a) Turn the ignition switch ON.
(b) Select the item ºDIAGNOSIS / ENHANCED OBD II /
DATA LIST / ALL / STOP LIGHT SWº.
CHECK:
Read the signal displayed on the hand-held tester.
OK:
Brake PedalSpecified Condition
DepressedSTP Signal ON
ReleasedSTP Signal OFF
CHECK:
Measure the voltage between the specified terminals of the E7
and E8 ECM connectors.
OK:
Tester ConnectionBrake PedalSpecified Condition
ST1- (E8-12) - DepressedBelow 1.5 VST1 (E8 12)
E1 (E7-1)
Released7.5 to 14 V
OK Check for intermittent problems (See page
DI-3).
NG
Page 1332 of 3115
- DIAGNOSTICSENGINE
DI-283
476 Author: Date:
2004 LAND CRUISER (RM1071U)
OBD II scan tool (excluding hand-held tester):
1 Check operation of stop light.
CHECK:
Check if the stop lights come on and go off normally when the brake pedal is operated and released.
NG Check and repair stop light circuit.
OK
2 Check STOP fuse.
PREPARATION:
Remove the STOP fuse from the cowl side J/B LH.
CHECK:
Check the continuity of the STOP fuse.
OK:
Continuity
NG Check for short in all harness and components
connected to STOP fuse.
OK
3 Check stop light switch (See page BE-50).
NG Replace stop light switch.
OK
Page 1333 of 3115
A19642
Brake Pedal
DepressedBrake Pedal
Release
STP ON
() ()
ST1-(+)
(+) E8
E7
E1 (-)
DI-284
- DIAGNOSTICSENGINE
477 Author: Date:
2004 LAND CRUISER (RM1071U)
4 Check STP signal.
PREPARATION:
Turn the ignition switch ON.
CHECK:
Measure the voltage between the specified terminals of the E7
and E8 ECM connectors.
OK:
Tester ConnectionBrake Pedal PositionSpecified Condition
STP (E8 19) E1 (E7 1)Depressed7.5 to 14 VSTP (E8-19) - E1 (E7-1)ReleasedBelow 1.5 V
ST1- (E8-12) - DepressedBelow 1.5 VST1 (E8 12)
E1 (E7-1)
Released7.5 to 14 V
OK Check for intermittent problems
(See page DI-3).
NG
Page 1401 of 3115
DI-42
- DIAGNOSTICSENGINE
235 Author: Date:
2004 LAND CRUISER (RM1071U)P0442
(DI-245)
Evaporative Emission Control
System Leak Detected (Small
Leak)
After the negative pressure introduction has been completed, if
the pressure in the EVAP system sharply increases.
Hose or tube cracked, holed, damaged or loose seal ((3) in
Fig. 1)
Fuel tank cap incorrectly installed
Fuel tank cap cracked or damaged
Vacuum hose cracked, holed, blocked, damaged or discon-
nected ((1), (2), (4), (5), (6), (7), (8) and (9) in Fig. 1)
Fuel tank cracked, holed or damaged
Charcoal canister cracked, holed or damaged
Open or short in vapor pressure sensor circuit
Vapor pressure sensor
ECM
P0446
(DI-222)Evaporative Emission Control
System Vent Control CircuitSame as DTC No. P0441
P0451
(DI-268)Evaporative Emission Control
System Pressure Sensor/Switch
Range/PerformanceOpen or short in vapor pressure sensor circuit
Vapor pressure sensor
ECM
P0452
(DI-268)Evaporative Emission Control
System Pressure Sensor/Switch
Low InputOpen in vapor pressure sensor circuit
Vapor pressure sensor
ECM
P0453
(DI-268)Evaporative Emission Control
System Pressure Sensor/Switch
High InputShort in vapor pressure sensor circuit
Vapor pressure sensor
ECM
P0455
(DI-245)Evaporative Emission Control
System Leak Detected (Gross
Leak)
Same as DTC No. P0442
P0456
(DI-245)Evaporative Emission Control
System Leak Detected (Very
Small Leak)
Same as DTC No. P0442
P0500
(DI-274)Vehicle Speed Sensor ºAºCombination meter
Open or short in vehicle speed sensor circuit
P0503
(DI-274)Vehicle Speed Sensor ºAº Inter-
mittent/Erratic/High
Oen or short in vehicle s eed sensor circuit
Vehicle speed sensor
ECM-
P0504
(DI-278)Brake Switch ºAº/ºBº Correlation
Short in stop lamp switch signal circuit
STOP fuse
Stop lamp switch
ECM
-
P0505
(DI-286)Idle Air Control System
Air induction system
Electric throttle control system
PCV hose connection
P0560
(DI-290)System Voltage
Back-up power source circuit
EFI or ECD No. 1 fuse
ECM
P0571
(DI-993)Brake Switch ºAº Circuit
Stop light switch signal circuit
Stop light switch
ECM
-
P0604
(DI-294)Internal Control Module Random
Access Memory (RAM) ErrorECM
P0606
(DI-294)ECM/PCM ProcessorECM
P0607
(DI-294)Control Module PerformanceECM
