Page 24 of 3115
- AIR CONDITIONINGAIR CONDITIONING SYSTEM
AC-9
2734 Author: Date:
2004 LAND CRUISER (RM1071U)
3. INSPECT IDLE-UP SPEED
(a) Warm up engine
(b) Inspect idle-up speed when following conditions are es-
tablished.
Test conditions:
Fan speed selector at ºHIº position
Temperature control dial at ºCOOLº position
A/C switch ON
Put gear shift in neutral
Magnetic clutch conditionIdle-up speed
Magnetic clutch not engaged700 ± 50 rpm
Magnetic clutch engaged780 ± 50 rpm
If idle speed is not as specified, check the idle control system.
4. INSPECT FOR LEAKAGE OF REFRIGERANT
(a) Stop engine.
(b) Secure good ventilation (The gas leak detector may not
react to volatile gases which are not refrigerant, such as
evaporated gasoline and exhaust gas)
(c) Repeat the test 2 or 3 times
(d) Make sure that there is some refrigerant remaining in the
refrigeration system.
When compressor is OFF: approx. 392 - 588 kPa (4 - 6
kgf´cm
2, 57 - 85 psi)
(e) Bring the gas leak detector close to the drain hose before
performing the test.
HINT:
After the blower motor stops, leave the cooling for more
than 15 minutes.
Expose the gas leak detector sensor under the drain
hose.
When bring the gas leak detector close to the drain hose,
make sure that the gas leak detector does not react to the
volatile gases.
If gas leaks are detected, lift up the vehicle.
(f) If gas leaks are not detected on the drain hose, remove
the blower resistor from the cooling unit. Then insert the
gas leak detector sensor into the unit to perform the test.
(g) Disconnect the connector and leave the pressure switch
for approx. 20 minutes. Then bring the gas leak detector
close to the pressure switch to perform the test.
(h) Bring the gas leak detector close to the refrigerant lines.
Page 43 of 3115
AC1IP-04
I06811
I06808
- AIR CONDITIONINGCOMPRESSOR AND MAGNETIC CLUTCH
AC-67
2792 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
1. INSTALL COMPRESSOR
(a) Install the compressor with 3 bolts.
Torque: 49 N´m (500 kgf´cm, 36 ft´lbf)
(b) Connect the connector.
2. INSTALL FRONT DRIVE SHAFT LH
(See page SA-33)
3. CONNECT DISCHARGE AND SUCTION HOSES
(a) Lubricate 2 new O-rings with compressor oil and install
them to the hoses.
(b) Connect the both hoses with 2 bolts.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
NOTICE:
Hose should be connected immediately after the caps have
been removed.
4. INSTALL AND CHECK DRIVE BELT
(See page AC-17 and AC-15)
5. CONNECT NEGATIVE (-) TERMINAL CABLE TO BAT-
TERY
6. EVACUATE AIR FROM REFRIGERATION SYSTEM
AND CHARGE SYSTEM WITH REFRIGERANT
Specified amount: 1,050 ± 50 g (37.03 ± 1.76 oz.)
7. INSPECT FOR LEAKAGE OF REFRIGERANT
Using a gas leak detector, check for leaks of the refrigerant.
If there is a leakage, check the tightening torque at the joints.
8. INSPECT A/C OPERATION
Page 46 of 3115
AC1IM-03
I06808
I06811
AC-62
- AIR CONDITIONINGCOMPRESSOR AND MAGNETIC CLUTCH
2787 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. RUN ENGINE AT IDLE SPEED WITH A/C ON FOR
APPROX. 10 MINUTES
2. STOP ENGINE
3. DISCONNECT NEGATIVE (- ) TERMINAL CABLE
FROM BATTERY
4. DISCHARGE REFRIGERANT FROM REFRIGERATION
SYSTEM
5. REMOVE ENGINE UNDER COVER
6. REMOVE DRIVE BELT (See page AC-16)
7. DISCONNECT DISCHARGE AND SUCTION HOSES
Remove the 2 bolts and disconnect the both hoses.
NOTICE:
Cap the open fittings immediately to keep moisture or dirt
out of the system.
8. REMOVE FRONT DRIVE SHAFT LH
(See page SA-26)
9. REMOVE COMPRESSOR
(a) Disconnect the connector.
(b) Remove the 3 bolts and the compressor.
Page 50 of 3115
AC1IS-04
I24817
I24818
AC-70
- AIR CONDITIONINGCONDENSER
2795 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. DISCHARGE REFRIGERANT FROM REFRIGERATION
SYSTEM
HINT:
At the time of installation, refer to the following items evacuate
air from the refrigeration system and charge system with the re-
frigerant and inspect for leaks of the refrigerant.
Specified amount: 1,050 ± 50 g (37.03 ± 1.76 oz.)
2. REMOVE RADIATOR GRILL
3. REMOVE A/T AIR COOLED OIL COOLER
(See page AT-17)
4. REMOVE ENGINE UNDER COVER
5. REMOVE DISCHARGE TUBE
(a) Remove the bolt and disconnect the tube from the con-
denser.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(b) Loosen the nut and remove the tube.
Torque: 22 N´m (225 kgf´cm, 16 ft´lbf)
NOTICE:
Cap the open fittings immediately to keep moisture or dirt
out of the system.
HINT:
At the time of installation, lubricate 2 new O-rings with com-
pressor oil and install them on the tube.
6. DISCONNECT LIQUID TUBE
Remove the bolt and disconnect the tube.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
NOTICE:
Cap the open fittings immediately to keep moisture or dirt
out of the system.
HINT:
At the time of installation, lubricate a new O-ring with compres-
sor oil and install them on the tube.
Page 60 of 3115
I06743
AC1L9-05
I06744
- AIR CONDITIONINGFRONT A/C EVAPORATOR
AC-73
2798 Author: Date:
2004 LAND CRUISER (RM1071U)
FRONT A/C EVAPORATOR
ON-VEHICLE INSPECTION
1. INSPECT FOR LEAKAGE OF REFRIGERANT
(a) Remove the glove compartment door.
(b) Remove the lower No. 2 finish panel
(See page BO-84).
(c) Remove the No. 1 cooler cover.
(1) Disconnect the connector clamp.
(2) Remove the 8 screws and No. 1 cooler cover.
(d) Using a gas leak detector, check for leaks of refrigerant.
If there is a leakage of refrigerant, check the tightening torque
at the joints or check the evaporator.
(e) Install the No. 1 cooler cover.
2. INSPECT EXPANSION VALVE
(a) Check amount of gas during refrigeration cycle.
(b) Set on manifold gauge set.
(c) Operate A/C system at ºMAX. COOLº for approx. 5 min-
utes.
(d) Check expansion valve.
Check the low pressure reading drops to 0 kPa (0
kgf/cm
2, 0 psi).
If the low pressure reading is not as specified, replace the ex-
pansion valve with the tubes.
Page 62 of 3115
AC1LB-04
I06745
I07899
- AIR CONDITIONINGFRONT A/C EVAPORATOR
AC-75
2800 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. DISCHARGE REFRIGERANT FROM REFRIGERATION
SYSTEM
HINT:
At the time of installation, evacuate air from refrigeration system
and charge the system with the refrigerant and inspect for leaks
of the refrigerant.
Specified amount: 1,050 ± 50 g (37.03 ± 1.76 oz.)
2. DISCONNECT LIQUID AND SUCTION TUBES FROM
FRONT COOLING UNIT (See page AC-24)
3. REMOVE INSTRUMENT PANEL (See page BO-84)
4. REMOVE ANTENNA RELAY
(a) Disconnect the connector.
(b) Remove the 2 screws and the antenna relay.
5. REMOVE EVAPORATOR
(a) Disconnect the connector.
(b) Disconnect the connector clamp.
(c) Remove the 8 screws and the No .1 cooler cover.
(d) Pull out the evaporator.
Page 67 of 3115
AC1K6-04
I07892
I03838
SST
I03839
SST
SST Push Pull
Release
Lever
I06878
CorrectWrong AC-24
- AIR CONDITIONINGFRONT COOLING UNIT
2749 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. DISCHARGE REFRIGERANT FROM REFRIGERATION
SYSTEM
HINT:
At the time of installation, first evacuate air from refrigeration
system.
Then, charge the system with the refrigerant and inspect for
leaks of the refrigerant.
Specified amount: 1,050 ± 50 g (37.03 ± 1.76 oz.)
2. DISCONNECT LIQUID AND SUCTION TUBES
(a) Using SST, remove the 2 piping clamps.
SST 09870-00025 (Liquid tube)
09870-00015 (Suction tube)
(1) Insert SST to piping clamp.
HINT:
Confirm the direction of the piping clamp claw and SST referring
to the illustration on the caution label.
(2) Push down SST and release the clamp lock.
NOTICE:
Be careful not to deform the tubes when pushing SST.
(3) Pull SST slightly and push the release lever, then re-
move the piping clamp with SST.
(4) Remove the piping clamp from SST.
(b) Disconnect the both tubes.
NOTICE:
Cap the open fittings immediately to keep moisture or dirt
out of the system.
HINT:
At the time of installation:
Lubricate 4 new O-rings with compressor oil and install
them to the tubes.
After connection, check the fitting for claw of the piping
clamp.
3. REMOVE INSTRUMENT PANEL AND REINFORCE-
MENT (See page BO-84)
Page 85 of 3115
AC1JE-04
I25169
AC-92
- AIR CONDITIONINGPRESSURE SWITCH
2817 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. DISCHARGE REFRIGERANT FROM REFRIGERATION
SYSTEM
HINT:
At the time of installation, evacuate air from refrigeration system
and charge system with refrigerant and inspect for leakage of
refrigerant.
Specified amount: 1,050 ± 50 g (37.03 ± 1.76 oz.)
2. REMOVE RADIATOR GRILL
3. REMOVE PRESSURE SWITCH FROM LIQUID TUBE
Disconnect the connector and remove the pressure switch.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
HINT:
Lock the switch mount on the tube with an open-end
wrench, be careful not to deform the tube, and remove the
switch.
At the time of installation, lubricate a new O-ring with
compressor oil and install the switch.
