1998 TOYOTA 4RUNNER Owners Manual

4RUNNER (1998)
Booster battery
Positive terminal (º+º mark)
Positive terminal (º+º mark)
Jumper cable Discharged battery
4. Make the cable connections in the order a, b, c, d.
a. Connect the clamp of the posi-
tive (red) jumper cable to the posi-
tive (
) terminal on the discharged
battery.
b. Connect the clamp at the other
end of the positive (red) jumper
cable to the positive (
) terminal
on the booster battery.

4RUNNER (1998)
Discharged battery Jumper cable
Negative terminal
(º-º mark)
Booster battery
c. Connect the clamp of the nega-
tive (black) jumper cable to the
negative (
) terminal on the
booster battery.
d. Connect the clamp at the other
end of the negative (black) jumper
cable to a solid, stationary, un-
painted, metallic point of the ve-
hicle with the discharged battery.
The recommended connecting
points are shown in the following
illustrations:

4RUNNER (1998)
Connecting point for 5VZ- FE engine
Connecting point for 3RZ- FE engine
Do not connect it to or near any
part that moves when the engine is
cranked.

4RUNNER (1998)
CAUTION
When making the connections, to
avoid serious injury, do not lean
over the battery or accidentally
let the jumper cables or clamps
touch anything except the correct
battery terminals or the ground.
5. Start your engine in the normal
way. After starting, run it at about
2000 rpm for several minutes with
the accelerator pedal lightly de-
pressed.
6. Carefully disconnect the cables in the exact reverse order: the nega-
tive cable and then the positive
cable.
7. Carefully dispose of the battery cover clothsÐthey may now con-
tain sulfuric acid.
8. If removed, replace all the battery vent plugs.
If the cause of your battery discharg-
ing is not apparent (for example,
lights left on), you should have it
checked. If your engine stalls while driving...
1. Reduce your speed gradually, keep- ing a straight line. Move cautiously
off the road to a safe place.
2. Turn on your emergency flashers.
3. Try starting the engine again.
If the engine will not start, see ºIf
your vehicle will not startº.
CAUTION
If the engine is not running, the
power assist for the brakes and
steering will not work so steering
and braking will be much harder
than usual.
If your vehicle overheats
If your engine coolant temperature
gauge indicates overheating, if you
experience a loss of power, or if
you hear a loud knocking or ping-
ing noise, the engine has probably
overheated. You should follow this
procedure... 1. Pull safely off the road, stop the vehicle and turn on your emergen-
cy flashers. Put the transmission in
ºPº (automatic) or neutral (manual)
and apply the parking brake. Turn
off the air conditioning if it is being
used.
2. If coolant or steam is boiling out of the radiator or reservoir, stop the
engine. Wait until the steam sub-
sides before opening the hood. If
there is no coolant boiling over or
steam, leave the engine running.
CAUTION
To help avoid personal injury,
keep the hood closed until there
is no steam. Escaping steam or
coolant is a sign of very high
pressure.
If your engine stalls while
driving

4RUNNER (1998)
3. Visually check to see if the engine drive belt (fan belt) is broken or
loose. Look for obvious coolant
leaks from the radiator, hoses, and
under the vehicle. However, note
that water draining from the air
conditioning is normal if it has
been used.
CAUTION
When the engine is running, keep
hands and clothing away from the
moving fan and engine drive
belts.
4. If the engine drive belt is brokenor the coolant is leaking, stop the
engine immediately. Call a Toyota
dealer for assistance.
5. If the engine drive belt is O.K. and there are no obvious leaks, you
may help the engine cool down
more quickly by running it at about
1500 rpm for a few minutes with
the accelerator pedal lightly de-
pressed.
6. Check the coolant reservoir. If it is dry, add coolant to the reservoir
while the engine is running. Fill it
about half full.
CAUTION
Do not attempt to remove the ra-
diator cap when the engine and
radiator are hot. Serious injury
could result from scalding hot
fluid and steam blown out under
pressure.
7. After the engine coolant tempera-ture has cooled to normal, again
check the coolant level in the res-
ervoir. If necessary, bring it up to
half full again. Serious coolant loss
indicates a leak in the system. You
should have it checked as soon as
possible at your Toyota dealer. If you have a flat tireÐ
1. Reduce your speed gradually, keep- ing a straight line. Move cautiously
off the road to a safe place well
away from the traffic. Avoid stop-
ping on the center divider of a
highway. Park on a level spot with
firm ground.
2. Stop the engine and turn on your emergency flashers.
3. Firmly set the parking brake and put the transmission in ºPº (auto-
matic) or reverse (manual).
4. Have everyone get out of the ve- hicle on the side away from traffic.
5. Read the following instructions thoroughly.
CAUTION
When jacking, be sure to observe
the following to reduce the possi-
bility of personal injury: Follow jacking instructions.
Do not start or run the engine
while your vehicle is supported
by the jack.

4RUNNER (1998)
Stop the vehicle on a level firm
ground, firmly set the parking
brake and put the transmission
in ºPº (automatic) or reverse
(manual). Block the wheel diag-
onally opposite to the one be-
ing changed if necessary.
Make sure to set the jack prop-
erly in the jack point. Raising
the vehicle with jack improperly
positioned will damage the ve-
hicle or may allow the vehicle
to fall off the jack and cause
personal injury.
Never get under the vehicle
when the vehicle is supported
by the jack alone.
Use the jack only for lifting
your vehicle during wheel
changing.
Do not raise the vehicle with
someone in the vehicle.
When raising the vehicle, do
not put an object on or under
the jack.
Raise the vehicle only high
enough to remove and change
the tire.NOTICE
Do not continue driving with a
deflated tire. Driving even a shortdistance can damage a tire be-yond repair.
ÐRequired tools and spare
tire

4RUNNER (1998)
Cover
(on some models)
1. Get the required tools and spare tire.
1. Tool bag
2. Jack handle
3. Jack
To prepare yourself for an emergency,
you should fam iliarize yourself with
the use of the jack, each of the tools
and their storage locations.

4RUNNER (1998)
Turn the jack joint by hand.
To remove: Turn the joint in direction
1 until the jack is free.
To store: Turn the joint in direction 2
until the jack is firmly secured to pre-
vent it flying forward during a collision
or sudden braking.