1998 SSANGYONG MUSSO fuel

1F1-58 M162 ENGINE CONTROLS
FUEL PUMP
Requirements for Fuel Pump
ItemSpecified ValueItemSpecified Value
System Pressure
3.8 bar
Minimum Delivery at 8V 30 Litre/Hr
Maximum Pressure
8.5 bar (12 V)
Minimum Amount
of Fuel Supply
114 Liter/Hr (12 V, 3.8 bar, -
30 ~ +70°C)
Minimum Pressure5.0 bar (12 V)
Maximum Allowable Current 7.5 A
Nominal Voltage
12 V
Ambient Temperature
-30 ~ +70°C
1 Reservoir Tank
2 Fuel Sensor (float/arm)
3 Resistance
4 Wiring Connector
5 Fuel Supply Pipe
7 Float
10 Flange and Harness Assembly
11 Fuel Pump
12 Spring
13 Thermister Housing
14 Thermister
15 Resistor Card and Wiper
16 Float Arm
Operating Voltage 8 V
Maximum Amount
of Fuel Supply165 Liter/Hr (12V, 3.8 bar,
-30 ~ +70°C)

M162 ENGINE CONTROLS 1F1-59
1
2
3
4
1 Fuel Pump Connector Wiring
2 Fuel Return Pipe
3 Fuel Supply Pipe
4 Bolts5 Fuel Return Pipe
6 Fuel Supply Pipe
7 Float
8 Ground Stud (Sender "-")
COLOR
Pump "+"
Thermister "+"
Ground
Sender Unit "+"USE Harness Location & Connector
A
B
C
D
2.0 BR
0.5 W
2.0 B
0.5 RY

1F1-60 M162 ENGINE CONTROLS
Tools Required
661 589 00 46 00 Cap Remover
Removal & Installation Procedure
1. Disconnect the negative battery cable.
2. Disconnect the harness connector (1).
3. Disconnect the fuel supply (6) and return (5) pipes.
4. Using a special tool, Unscrew the eight fuel retaining bolts
and remove the pump from fuel tank.
Notice
Check the condition of the seal and replace if necessary.
Drain the fuel before removing the pump.

M162 ENGINE CONTROLS 1F1-61
Notice
Replace the fuel pump relay if the measured value is over
9A. Notice
Check the fuel filter and fuel line when the fuel delivery is
not within specified value.
Measure the Current Consumption of Fuel Pump
1. Remove the fuel pump relay from fuse and relay box in
trunk, and turn the ignition switch to "ON" position.
2. Using a multi-tester, measure the current consumption by
connecting the terminal No.1 and No.3 of pump.
Measure the Fuel Delivery From the Fuel Pump
1. Disconnect the return pipe from fuel distributor and insert
the appropriate hose into it.
2 . Place the hose end into the beaker with the minimum capacity
of 1Liter.
3. Turn the ignition switch to "ON" position.
4. Connect the terminal No.33 and No.5 of ECU with a service
wire.
5. Measure the fuel delivery from the fuel pump.
1Liter/max.35sec. Specifed Value
5 - 9A Specifed Value

1F1-62 M162 ENGINE CONTROLS
PURGE SWITCHOVER VALVE
1 Purge Switchover Valve
2 Line to Engine
3 Line to Canister
4 Canister
Functions
The fuel vaporization control system is installed to inhibit the
fuel vaporized gas from discharging into the atmosphere. The
fuel vaporized gas that is accumulated in the canister abstracts
through the purge switchover valve purification during the
engine combustion (except the decreasing mode) and coolant
temperature of over 80°C. For this reason, the ECU transacts
the engine speed, air inflow quantity, coolant temperature, and
intake temperature.
The purge switchover valve is activated by the ECU frequency
according with the engine rotating speed to adjust the
purification rate. The purification rate is determined by the
continuous valve opening interval.
The purge switchover valve is activated by the ECU for the
following conditions :
lCoolant temperature of over 80°C
lEngine speed of over 1000rpm
l2 Minutes after starting
lWhen the fuel cut-off mode is not activated

1F1-64 M162 ENGINE CONTROLS
VACUUM SYSTEM
1 Purge Control Valve
2 Molded Hose
3 Insulator
4 Fuel Tube
5 Molded Hose
6 Idle Regulator
7 Resonance Flap
8 Intake Manifold
9 Fuel Pressure Regulator10 Vacuum Line Rubber Hose
11 Vacuum Tube(Gray, 270mm)
12 Molded Hose
13 Rubber Cap
18 Rubber Hose
19 Vacuum Tube(Brown or Black, 770mm)
20 Rubber Hose
A To Canicter

1F1-72 M162 ENGINE CONTROLS
OXYGEN SENSOR
1 Electricity Wire
2 Oxygen Sensor Housing
3 Sensor Ceramic
4 Electrode (Internal)
5 Electrode (External)
6 Heating Coil
7 Open Space
8 Protector Tube
Functions
The oxygen sensor optimizes the combustion (Air-Fuel Ratio
14.7:1) and resets the Air-fuel ratio in the ECU after sensing
the amount of oxygen from the exhaust gases to diminish the
exhaust gases.
- Rich(<1) above approx. 450mV
- Lean(>1) below approx. 450mV
Locatoin of Sensor
Oxygen sensor is located on the front exhaust pipe.

SECTION 1F2
M161 ENGINE CONTROLS
TABLE OF CONTENTS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1F2-2
Fastener Tightening Specifications . . . . . . . . 1F2-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1F2-3
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1F2-3
Schematic and Routing Diagrams . . . . . . . 1F2-4
E23 ECU (MSE) . . . . . . . . . . . . . . . . . . . . . . 1F2-4
E23 ECU (HFM) . . . . . . . . . . . . . . . . . . . . . . 1F2-5
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 1F2-6
Self Diagnosis Socket Pin Numbers and
Descriptions . . . . . . . . . . . . . . . . . . . . . . . . 1F2-6
Self Diagnosis Failure Code (for E23 ENG) . 1F2-7
Test Box Connection . . . . . . . . . . . . . . . . . . 1F2-10
Fuel Injection System Test . . . . . . . . . . . . . 1F2-11
Ignition System Test . . . . . . . . . . . . . . . . . . 1F2-20
Idling Control and Electronic Pedal
System Test . . . . . . . . . . . . . . . . . . . . . . . 1F2-25
Air Conditioner Control System Test . . . . . . 1F2-27
Fuel Pressure and Internal Leakage Test . . 1F2-28
Fuel Pump Test . . . . . . . . . . . . . . . . . . . . . . 1F2-30Injector Test . . . . . . . . . . . . . . . . . . . . . . . . 1F2-32
Maintenance and Repair . . . . . . . . . . . . . 1F2-34
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 1F2-34
ECU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F2-34
Fuel Pressure Regulator . . . . . . . . . . . . . . 1F2-45
Fuel Distributor . . . . . . . . . . . . . . . . . . . . . . 1F2-49
Injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F2-54
Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 1F2-57
Fuel Pump . . . . . . . . . . . . . . . . . . . . . . . . . 1F2-58
Purge Switchover Valve . . . . . . . . . . . . . . . 1F2-62
Vacuum System . . . . . . . . . . . . . . . . . . . . . 1F2-64
Crankshaft Position Sensor . . . . . . . . . . . . 1F2-66
Camshaft Position Sensor . . . . . . . . . . . . . 1F2-68
Hot Film Air Mass (HFM) Sensor . . . . . . . . . 1F2-70
Oxygen Sensor . . . . . . . . . . . . . . . . . . . . . . 1F2-73
Knock Sensor . . . . . . . . . . . . . . . . . . . . . . . 1F2-75
Coolant Temperature Sensor . . . . . . . . . . . 1F2-76
Accelerator Pedal Module . . . . . . . . . . . . . . 1F2-79