1998 SSANGYONG MUSSO clock

1B1-20 M162 ENGINE MECHANICAL
Removal & Installation Procedure
1. Remove the belt pulley.
Installation Notice
2. Disconnect the hydraulic pipe of the power steering pump
and drain the oil.
3. Unscrew the bolts (arrows) and remove the steering pump.
Installation Notice Notice
Pull the tensioning pulley clockwise as shown in the figure.
4. Remove the compressor after disconnecting the wiring
connector and refrigerant pipe of A/C compressor.
Notice
Discharge all the refrigerant before removing the pipes.
Tightening Torque 40.5 - 49.5 Nm
Tightening Torque 22.5 - 27.5 Nm

M162 ENGINE MECHANICAL 1B1-25
POLY V - BELT
Preceding Work : Removal of cooling fan
1 Poly V-belt
Removal & Installation Procedure
1. Release the belt tension by turning the belt tensioning pulley
nut clockwise.
2. Remove the poly v-belt.
Notice
Check the belt for damage and tensioning pulley bearing
point for wear and replace them if necessary.
3. Install the belt by turning the nut of tensioning pulley
clockwise.
2 Belt Tensioning Pulley

M162 ENGINE MECHANICAL 1B1-27
TENSIONING DEVICE
Preceding Work : Removal of poly v-belt
1 Belt (L = 2245)
2 Bolt Combi(M8 x 14, 3 pieces) + Washer
.......................................................22.5-27.5Nm
Removal & Installation Procedure
1. Remove the poly v-belt.
2. Remove the tensioning pulley by turning its mounting nut
counter clockwise as shown in figure.
Installation Notice3 Water Pump Pulley
4 Nut
5 Tensioning Pulley
Tightening Torque 40.5 - 49.5 Nm

M162 ENGINE MECHANICAL 1B1-61
8 . Unscrew the intake side bolts (8, 11, 13, 14) and the exhaust
side bolts (1, 4, 6, 7).
9. Loosen the remaining bolts and unscrew the intake and
exhaust side camshaft bearing cap bolts.
Notice
Number the camshaft bearing cap bolts when removing
them, so that they don’t get mixed up.
10. Remove the intake and exhaust camshafts.
Installation Procedure
1. Turn the crankshaft and position the No. 1 cylinder piston
at BTDC 30°.
Notice
Turn the crankshaft in the direction of engine rotation.
3. Turn the camshaft using the wrench (special tool) so that
the intake camshaft adjustment hole lines up with the cylinder
head upper side (3 o’clock direction at the intake, 9 o’clock
direction at the exhaust).
Notice
Turn the crankshaft and adjust it to OT so that No. 1 cylinder’s
piston would be at TDC. Install the bearing caps according to the numbers on the
bearing caps.
Tightening Torque 22.5 - 27.5 Nm 2. Install the exhaust camshaft bearing caps (2, 3, 5) and the
intake camshaft bearing caps (9, 10, 12). Tighten the bolts
with specified torque and install the remaining bearing caps.
Notice

M162 ENGINE MECHANICAL 1B1-65
Adjustment Procedure
1. Position the No.1 cylinder to BTDC 30° .
2. Remove the chain tensioner.
3. Remove the exhaust camshaft sprocket.
4. Align the intake and exhaust camshaft flange hole with the
cylinder head upper surface.
lIntake Side : 3 o’clock direction
lExhaust Side : 9 o’clock direction
5. Secure the intake and exhaust camshaft.
6. Position the piston of No.1 cylinder at TDC (OT) by turning
the crankshaft.
7. Turn the camshaft adjuster of the intake camshaft to the
left as much as possible (cam adjuster ‘retarded’ position).
8. Install the chain to the intake camshaft sprocket.
Notice
Timing chain must be placed on the guide rail in gear case
cover. Tools Required
104 589 01 01 00Spanner
Inspection
1. Position the No.1 cylinder piston to TDC (OT) by turning
the crankshaft.
Notice
When the OT mark on vibration damper is aligned with timing
gear case cover, the intake and exhaust cam of cylinder
will make the slope to the center and will face up. In this
way, the adjustment hole of the intake and exhaust camshaft
will match in line with the cylinder head upper end, at 3
o’clock, and 9 o’clock direction each other.
2. Check the timing as below procedure;
- Check if the camshaft adjustment hole is positioned to 3
o’clock direction at the intake side and to 9 o’clock
direction at the exhaust side, respectively and align with
the cylinder head mating surface.
- At this condition, check if the OT mark on vibration
damper aligns with the marker on the timing gear case.

M161 ENGINE MECHANICAL 1B2-23
Removal & Installation Procedure
1. Remove the belt pulley after removal of poly v-belt.
Installation Notice
2. Disconnect the hydraulic pipe of the power steering pump
and drain the oil.
3. Unscrew the bolts (arrows) and remove the steering pump.
Installation Notice Notice
Pull the tensioning pulley counterclockwise as shown in the
figure.
4. Remove the compressor after disconnecting the wiring
connector and refrigerant pipe of A/C compressor.
Notice
Discharge all the refrigerant before removing the pipes.
Tightening Torque 40.5 - 49.5 Nm
Tightening Torque 22.5 - 27.5 Nm

1B2-28 M161 ENGINE MECHANICAL
POLY V-BELT
Preceding Work : Removal of cooling fan
1 Poly V-belt (2,155 mm)
2 Belt Tensioning Pulley
Removal & Installation Procedure
1. Release the belt tension by turning the stud on the cap with
12 sided wrench or spanner counterclockwise.
2. Remove the poly v-belt.
Notice
Check the belt for damage and tensioning pulley bearing
point for wear and replace them if necessary.
3. Install the belt after prying the tensioning pulley.
3 Belt Tensioner

1B2-30 M161 ENGINE MECHANICAL
TENSIONING DEVICE
Preceding Work : Removal of tensioning device shock absorber
1 Bolt (M8 x 75, 2 pieces) +
Washer ..........................................22.5-27.5 Nm
2 Bolt (M8 x 25, 1 pieces) +
Washer ..........................................22.5-27.5 Nm
Removal & Installation Procedure
1. Turn the stud bolt to counterclockwise.
2. Insert the pin (111 589 01 15 00) into the hole in tensioning
arm.
3. Unscrew the bolts (1, 2) and remove the tensioning device.
Installation Notice
4. Installation should follow the removal procedure in the
reverse order.3 Tensioning Device
4 Stud bolt
5 Tensioning Arm
Tightening Torque 22.5 - 27.5 Nm