1998 SSANGYONG MUSSO clock

1B3-36 OM600 ENGINE MECHANICAL
Setting (with cylinder head installed)
1. Remove the prechamber of No. 1 cylinder.
2. Position the piston of No.1 cylinder at BTDC 10.
3. Install the measuring device into the prechamber bore and
position the dial gauge with a preload of 5mm.
Dial Gauge 001 589 53 21 00
Depth Gauge 601 589 07 21 00
4. Slowly rotate the crankshaft in the direction of engine rotation
until the large pointer on the dial gauge stops (TDC position).
Notice
The position of TDC is when the large pointer on the dial
gauge is stopped before moving back.
5. remove the reinstall the measuring device and position the
dial gauge scale at ‘0’.
6. Slowly rotate the crankshaft in the direction of engine rotation
until the dial gauge has moved back (counterclockwise) by
3.65mm.
7. Insert fixing device into the sensor bracket.
Notice
The pin on the vibration damper must engage into the slot
of the fixing device.
Fixing Device 667 589 01 21 00
8. If the pin does not engage, adjust the setting of the sensor
bracket by removing and tightening of the sensor bracket
bolts.
Tightening Torque 10 Nm
Notice
The timing mark on the damper must be positioned at ATDC
20.

OM600 ENGINE CONTROLS 1F3-3
FUEL INJECTION PUMP CODING
Model Code
PES 4M 55C 320 RS 167
PES 5M 55C 320 RS 168
Fuel Injection Pump Code
Example)PES 5M 55C 320 RS 168
P Pump
E Self-Driven
S End Flange Mounting
5 Number of Cylinders (5EA)
M Pump Size
55 Element Diameter
C Modification Letter
320 Assembly Number
R Direction of Rotation (clockwise)
S188 Special Version
RSF Governor
R Governor
S Coil Spring
F Drive Governor
Component Location
1. Fuel Injection Pump
2. Vacuum Unit (Stop Unit)
3. Control Lever
4. PLA Vacuum Unit (Idle Speed Adjustment)
5. Governor
6. Fuel Pump
OM661 LA Engine
OM662 LA Engine

OM600 ENGINE CONTROLS 1F3-17
6. After adjustment, tighten the locking nut and place the
position marking with different color of paint.
Notice
If there are no changes in idle speed with PLA unit
adjustment, perform the service at a BOSCH Service Center.
7. Connect the vacuum pump to the PLA vacuum unit and
build up vacuum approx. 500mbar. If engine rpm increases
by approx. 100rpm, It is normal.
Vacuum Pump 001 589 73 21 00
8. Connect the vacuum line (4).
9. Switch on all ancillaries and check the idle speed.
5. Ensure not to damage the idle spring in the governor and
adjust idle speed by turning the PLA unit (5) slowly.
Notice
Do not rotate the PLA unit over ½ turn from the position
marking. If do, idle spring in the governor will be severely
damaged.Clockwise
Counterclockwise
RPM Decrease
RPM Increase

REAR DRIVE AXLE 3D-17
Inspection
lRemove the LSD assembly and check the pre-load torque.
lIf necessary, replace LSD assembly.
Procedure
1. Fix the right shaft of LSD to the special tool (A).
2. Install the special tool (B) to the left shaft and rotate
counterclockwise and check the pre-load torque.
Normal Torque 3.6 - 9.0kgm
Notice
If necessary, replace LSD assembly.

AUTOMATIC TRANSMISSION 5A-49
POWER FLOW - REVERSE
In Reverse, transmission drive is via the input shaft and the forward clutch cylinder to the hub of the C3 clutch. The
elements of the transmission function as follows :
lThe C3 clutch is engaged and drives the reverse sun gear in a clock-wise direction.
lThe B2 band is engaged and holds the planetary gear carrier stationary causing the long pinion to rotate anti-
clockwise about its axis on the pinion shaft.
lThe long pinion drives the internal ring fear in the same direction.
lThe internal ring being splined to the output shaft drives it in an anti-clockwise or reverse direction.
Control
To maintain this arrangement in the steady state
solenoids and valves are activated as follows:
lSolenoids S1 and S2 are switched off.
lLine pressure is directed through the reverse lockout valve to both the inner and outer apply areas of the rear
servo piston for B2 band application.
lLine pressure feeds the reverse oil circuit via the manual valve.
lReverse oil is routed from the manual valve to the C3 clutch.
lReverse oil is also applied to the spring end of the primary regulator valve to assist the spring and to boost the
line pressure value.
lAll other clutch and band apply circuits are open to exhaust.
Refer to figure 5.2 and table 5.3
Table 5.3 - Engaged Elements - Reverse
Gear State
ReverseC1
-C2
-C3
XC4
-B1
-B2
X1-2
OWC
-3-4
OWC
-LU
CLUTCH
- ELEMENTS ENGAGED

5A-50 AUTOMATIC TRANSMISSION
POWER FLOW - MANUAL 1
In Manual 1, transmission drive is via the input shaft
to the forward clutch cylinder. The elements of the
transmission function as follows :
lThe C2 clutch is engaged to drive the forward sun gear, via the 3-4 OWC.
lThe B2 band is engaged to hold the planetary gear carrier stationary.
lThe forward sun gear drives the short pinion anti-clockwise.
lThe short pinion drives the long pinion clockwise.
lThe long pinion rotating about its axis drives the internal ring gear and the output shaft in a clockwise or
forward direction.
lThe C4 clutch provides engine braking through the 3-4 OWC on overrun.
Control
To maintain this arrangement in the steady state solenoids and valves are activated as follows:
lSolenoids S1 and S2 are switched ON.
lThe 1-2,2-3, and 34 shift valves are held in their first gear positions by line 500 pressure.
lDrive (line pressure) oil from the manual valve engages the C2 clutch.
lLo-1st (line pressure) oil is routed through the 1-2 shift valve to the C4 clutch, and to the inner apply area of
the rear servo piston for B2 band application.
Refer to figure 5.3 and table 5.4.
Table 5.4 - Engaged Elements - Manual 1
Gear State
Manual 1C1
-C2
XC3
-C4
XB1
-B2
X1-2
OWC
-3-4
OWC
XLU
CLUTCH
- ELEMENTS ENGAGED

AUTOMATIC TRANSMISSION 5A-51
POWER FLOW - DRIVE 1
In Drive 1, transmission drive is via the input shaft to the forward clutch cylinder. The elements of the transmission
function as follows :
lThe C2 clutch is engaged to drive the forward sun gear.
lThe forward sun gear drives the short pinion anti-clockwise.
lThe short pinion drives the long pinion clockwise.
lThe 1-2 OWC prevents the planetary gear carrier from rotating under reaction force and the long pinion
rotates on its axis driving the internal ring gear and output shaft in a clockwise or forward direction.
lThere is no engine braking on overrun.
Control
To maintain this arrangement in the steady state solenoids and valves are activated as follows:
lSolenoids S1 and S2 are switched On.
lThe 1-2, 2-3, and 3-4 shift valves are held in their first gear positions by line 500 pressure.
lDrive (line pressure) oil from the manual valve engages the C2 clutch.
Refer to figure 5.4 and table 5.5
Table 5.5 - Engaged Elements - Drive 1
Gear State
Drive 1C1
-C2
XC3
-C4
-B1
-B2
-1-2
OWC
X3-4
OWC
XLU
CLUTCH
- ELEMENTS ENGAGED

5A-52 AUTOMATIC TRANSMISSION
POWER FLOW - DRIVE 2 AND MANUAL 2
In Drive 2 and Manual 2, transmission drive is via the input shaft and forward clutch cylinder. The elements of the
transmission function as follows :
lThe C2 clutch is applied to drive the forward sun gear.
lThe forward sun gear drives the short pinion anti-clockwise.
lThe short pinion drives the long pinion clockwise.
lThe B1 band is applied holding the reverse sun gear stationary therefore the long pinion ‘walks’ around the
reverse sun gear taking the internal ring gear and output shaft with it in a clockwise or forward direction.
lThe C4 clutch is applied to bypass the 3-4 OWC and provide engine braking on overrun.
Control
To maintain this arrangement in the steady state solenoids and valves are activated as follows: Solenoid S1 is
switched Off. S2 is switched On.
lSolonoid S1 is switched Off. S2 is switched On.
lDrive (line pressure) oil from the manual valve engages the C2 clutch.
lWhen S1 switches off , S1 oil pressure, which is derived from line 500 pressure, moves the 3-4 shift valve to
the left. At the same time S1 oil is directed to the 1-2 shift valve which moves the valve to the second gear
position.
l2nd oil (line pressure) from the 1-2 shift valve is directed to the band apply regulator valve, and to the 2-3 shift
valve.
lThe band apply regulator valve supplies 2nd oil (regulated to line pressure multiplied by the valve ratio) to the
band apply feed (BAF) circuit.
lBand apply feed oil is directed to:
- The outer apply area of the front servo
- The 1-2 shift valve to provide an exhaust port when the transmission is shifted to first gear
- The 3-4 shift valve for use when the transmission is shifted into fourth gear
lDrive (line pressure) is routed through the 3-4 shift valve to apply the C4 clutch.
Refer to figure 5.5 and table 5.6.
Table 5.6 - Engaged Elements - Drive 2 and Manual 2
Gear State
Drive 2 and Manual 2C1
-C2
XC3
-C4
XB1
XB2
-1-2
OWC
-3-4
OWC
XLU
CLUTCH
- ELEMENTS ENGAGED