1998 SSANGYONG MUSSO battery

0B-4 GENERAL INFORMATION
Specifications
RACK & PINION
0 - 4 mm
2°30’± 30’
0° ± 30’
1L Application
Gear Type
Wheel Alignment:
Front Toe-in
Front Caster
Front Camber
Oil Capacity
Steering System
Application
Front Type
Rear Type
Suspension
Specifications
Double Wishbone
5 - Link
Application
Fuel Pump Type
Fuel Filter Type
Fuel Capacity
Specifications
Electric Motor Pump
Cartridge
70 L
Fuel System
Lubricating Type
Oil Pump Type
Oil Filter Type
Oil Capacity (L) (Including Oil Filter)
Lubricating System
661LA
8.0662NA
9.0662LA
9.52.0L DOHC
7.22.3L DOHC
7.53.2L DOHC
8.2
External Gear pump
Combination(Full & Part)
Full Flow
Cooling Type
Coolant Capacity (L)
Radiator Type
Water Pump Type
Cooling System
661LA
9.5-10662NA
10.5662LA
10.5-112.0L DOHC
10.52.3L DOHC
10.53.2L DOHC
11.3
Forced Circulation
Centrifugal
Application
Battery (MF)
Generator
Starter
Electric System
661LA
75A
2.2kw662NA
75A
2.2kw662LA
75A
2.2kw2.0L DOHC
115A
1.2kw2.3L DOHC
115A
1.2kw3.2L DOHC
115A
1.7kw
12V - 90AH12V - 75AH

GENERAL INFORMATION 0B-15
GENERAL DESCRIPTION
AND SYSTEM OPERATION
GENERAL REPAIR INSTRUCTIONS
lIf a floor jack is used, the following precautions are
recommended.
lPark the vehicle on level ground, “block” the front or
rear wheels, set the jack against the frame, raise the
vehicle and support it with chassis stands and then
perform the service operation.
lBefore performing the service operation, disconnect
the negative battery cable in order to reduce the
chance of cable damaged and burning due to short-
cir cuiting.
lUse a cover on the body, the seats and the floor to
protect them against damage and contamination.
lHandle brake fluid and antifreeze solution with care
as they can cause paint damage.
lThe use of proper tools, and the recommended
essential and available tools where specified, are
important for efficient and reliable performance of
the service repairs.lUse genuine DAEWOO parts.
lDiscard used cotter pins, gaskets, O-rings, oil seals,
lock washers and self-locking nuts. Prepare new ones
for installation. Normal function of these parts cannot
be maintained if these parts are reused.
lKeep the disassembled parts neatly in groups to
facilitate proper and smooth reassembly.
lKeep attaching bolts and nuts separated, as they
vary in hardness and design depending on the
position of the installation.
lClean the parts before inspection or reassembly.
lAlso clean the oil parts, etc. Use compressed air to
make certain they are free of restrictions.
lLubricate rotating and sliding faces of parts with oil
or grease before installation.
lWhen necessary, use a sealer on gaskets to prevent
leakage.
lCarefully observe all specifications for bolt and nut
torques.
lWhen service operation is completed, make a final
check to be sure service was done properly and the
problem was corrected.

1A1-12 GENERAL ENGINE INFORMATION
Leakage Test
1. Warm the engine up to normal operating temperature.
2. Disconnect the negative battery cable.
3. Remove the spark plugs.
4. Check the coolant level by opening the coolant surge tank
cap and replenish if insufficient.
5. Open the engine oil filler cap.
6. Connect the tester to air pressure line and adjust the scale
of tester.
7. Install the connecting hose to spark plug hole.
9. Connect the connecting hose to tester and measure the
leakage volume after blowing up 5bar of compressed air.
Notice
Measure the leakage volume in the completely opening
condition of throttle valve by pulling the acceleration cable.
10. Perform the pressure test according to the firing order.
Notice
Firing Order : 1 - 5 - 3 - 6 - 2 - 4
11. Compare the leakage pressure with the specifications.8. Position the piston of No.1 cylinder at TDC by rotating the
crankshaft.

GENERAL ENGINE INFORMATION 1A1-13
GENERAL INFORMATION
CLEANLINESS AND CARE
An automobile engine is a combination of many
machined, honed, polished and lapped surfaces with
tolerances that are measured in the ten-thousanths of
an inch. When any internal engine parts are serviced,
care and cleanliness are important. A liberal coating of
enigne oil should be applied to friction areas during
assembly, to protect and lubricate the surfaces on initial
operation. Proper cleaning and protection of machined
surfaces and friction areas is part of the repair
procedure. This is considered standard shop practice
even if not specifically stated.
Whenever valve train components are removed for
service, they should be kept in order. They should be
installed in the same locations, and with the same mating
surfaces, as when they were removed.Battery cables should be disconnected before any major
work is performed on the engine. Failure to disconnect
cables may result in damage to wire harness or other
electrical parts.
ON-ENGINE SERVICE
Caution: Disconnect the negative battery cable
before removing or installing any electrical unit, or
when a tool or equipment could easily come in
contact with exposed electrical terminals.
Disconnecting this cable will help prevent personal
injury and damage to the vehicle. The ignition must
also be in LOCK unless otherwise noted.
Notice: Any time the air cleaner is removed, the intake
opening should be covered. This will protect against
accidental entrance of foreign material, which could
follow the intake passage into the cylinder and cause
extensive damage when the engine is started.

GENERAL ENGINE INFORMATION 1A2-13
Leakage Test
1. Warm the engine up to normal operating temperature.
2. Disconnect the negative battery cable.
3. Remove the spark plugs.
4. Check the coolant level by opening the coolant surge tank
cap and replenish if insufficient.
5. Open the engine oil filler cap.
6. Connect the tester to air pressure line and adjust the scale
of tester.
7. Install the connecting hose to spark plug hole.
9. Connect the connecting hose to tester and measure the
leakage volume after blowing up 5bar of compressed air.
Notice
Measure the leakage volume in the completely opening
condition of throttle valve by pulling the acceleration cable.
10. Perform the pressure test according to the firing order.
Notice
Firing Order : 1 - 3 - 4 - 2
11. Compare the leakage pressure with the specifications.8. Position the piston of No.1 cylinder at TDC by rotating the
crankshaft.

1A2-14 GENERAL ENGINE INFORMATION
GENERAL INFORMATION
CLEANLINESS AND CARE
An automobile engine is a combination of many
machined, honed, polished and lapped surfaces with
tolerances that are measured in the ten-thousanths of
an inch. When any internal engine parts are serviced,
care and cleanliness are important. A liberal coating of
enigne oil should be applied to friction areas during
assembly, to protect and lubricate the surfaces on initial
operation. Proper cleaning and protection of machined
surfaces and friction areas is part of the repair
procedure. This is considered standard shop practice
even if not specifically stated.
Whenever valve train components are removed for
service, they should be kept in order. They should be
installed in the same locations, and with the same mating
surfaces, as when they were removed.
Battery cables should be disconnected before any major
work is performed on the engine. Failure to disconnect
cables may result in damage to wire harness or other
electrical parts.
ON-ENGINE SERVICE
Caution: Disconnect the negative battery cable be-
fore removing or installing any electrical unit, or
when a tool or equipment could easily come in con-
tact with exposed electrical terminals. Disconnect-
ing this cable will help prevent personal injury and
damage to the vehicle. The ignition must also be in
LOCK unless otherwise noted.
Notice: Any time the air cleaner is removed, the intake
opening should be covered. This will protect against
accidental entrance of foreign material, which could
follow the intake passage into the cylinder and cause
extensive damage when the engine is started.

GENERAL ENGINE INFORMATION 1A3-15
GENERAL INFORMATION
CLEANLINESS AND CARE
An automobile engine is a combination of many
machined, honed, polished and lapped surfaces with
tolerances that are measured in the ten-thousanths
of an inch. When any internal engine parts are
serviced, care and cleanliness are important. A liberal
coating of enigne oil should be applied to friction areas
during assembly, to protect and lubricate the surfaces
on initial operation. Proper cleaning and protection
of machined surfaces and friction areas is part fo the
repair procedure. This is considered standard shop
practice even if not specifically stated.
Whenever valve train components are removed for
service, they should be kept in order. They should be
installed in the same locations, and with the same
mating surfaces, as when they were removed.Battery cables should be disconnected before any
major work is performed on the engine. Failure to
disconnect cables may result in damage to wire
harness or other electrical parts.
ON-ENGINE SERVICE
Caution: Disconnect the negative battery cable
before removing or installing any electrical unit,
or when a tool or equipment could easily come in
contact with exposed electrical terminals.
Disconnecting this cable will help prevent
personal injury and damage to the vehicle. The
ignition must also be in LOCK unless otherwise
noted.
Notice: Any time the air cleaner is removed, the intake
opening should be covered. This will protect against
accidental entrance of foreign material, which could
follow the intake passage into the cylinder and cause
extensive damage when the engine is started.

SECTION 1B1
M162 ENGINE MECHANICAL
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1B1-2
Fastener Tightening Specifications . . . . . . . . 1B1-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1B1-4
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1B1-4
Maintenance and Repair . . . . . . . . . . . . . . 1B1-8
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1B1-8
Engine Assembly . . . . . . . . . . . . . . . . . . . . . 1B1-8
Crankcase Ventilation System . . . . . . . . . . 1B1-16
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-18
Power Steering Pump and A/C Bracket . . . 1B1-19
Hydraulic Engine Mounting Insulator . . . . . . 1B1-22
Poly V-Belt . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-25
Tensioning Device . . . . . . . . . . . . . . . . . . . . 1B1-27
Poly V-Belt Inspection . . . . . . . . . . . . . . . . . 1B1-29
Cylinder Head Cover . . . . . . . . . . . . . . . . . 1B1-31
Cylinder Head Front Cover . . . . . . . . . . . . . 1B1-33
Cylinder Head . . . . . . . . . . . . . . . . . . . . . . . 1B1-35
Timing Gear Case Cover . . . . . . . . . . . . . . 1B1-38
Crankshaft Sealing Rear Cover . . . . . . . . . 1B1-40
Belt Pulley and Vibration Damper . . . . . . . . 1B1-42
Crankshaft Front Radial Seal . . . . . . . . . . . 1B1-45
Crankshaft Rear Radial Seal . . . . . . . . . . . 1B1-46
Crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-47
Flywheel / Driven Plate . . . . . . . . . . . . . . . . 1B1-53
Camshaft Adjuster . . . . . . . . . . . . . . . . . . . 1B1-55
Camshaft Sprocket Bolt . . . . . . . . . . . . . . . 1B1-58
Camshaft . . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-59
TABLE OF CONTENTS
Camshaft Timing Position . . . . . . . . . . . . . . 1B1-64
Valve Spring . . . . . . . . . . . . . . . . . . . . . . . . 1B1-67
Valve Stem Seal . . . . . . . . . . . . . . . . . . . . . 1B1-71
Chain Tensioner . . . . . . . . . . . . . . . . . . . . . 1B1-72
Timing Chain . . . . . . . . . . . . . . . . . . . . . . . . 1B1-75
Tensioning Rail . . . . . . . . . . . . . . . . . . . . . . 1B1-80
Cylinder Head Guide Rail . . . . . . . . . . . . . . 1B1-81
Crankcase Guide Rail . . . . . . . . . . . . . . . . . 1B1-82
Crankshaft Sprocket . . . . . . . . . . . . . . . . . . 1B1-83
Piston . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-85
Connecting Rod . . . . . . . . . . . . . . . . . . . . . 1B1-88
Piston Ring . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-90
Engine Oil Specification . . . . . . . . . . . . . . . 1B1-92
Oil Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-93
Engine Oil and Oil Filter Element . . . . . . . . 1B1-95
Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-97
Oil Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-99
Oil Pressure Relief Valve . . . . . . . . . . . . . 1B1-101
Oil Non-Return Valve . . . . . . . . . . . . . . . . 1B1-102
Oil Dipstick Guide Tube . . . . . . . . . . . . . . 1B1-103
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . 1B1-104
Oil Gallery in Crankcase . . . . . . . . . . . . . . 1B1-104
Oil Gallery in Cylinder Head . . . . . . . . . . . 1B1-106
Core Plugs in Crankcase . . . . . . . . . . . . . 1B1-109
Cylinder Bore . . . . . . . . . . . . . . . . . . . . . . 1B1-111
Crankcase Mating Surface . . . . . . . . . . . . 1B1-113
Cylinder Head Mating Surface . . . . . . . . . 1B1-115