1998 SSANGYONG MUSSO battery

SECTION 1E1
M162 ENGINE ELECTRICAL
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1E1-1
Alternator Specifications . . . . . . . . . . . . . . . . 1E1-1
Starting Motor Specifications . . . . . . . . . . . . 1E1-2
Battery Specifications . . . . . . . . . . . . . . . . . . 1E1-2
Fastener Tightening Specifications . . . . . . . . 1E1-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1E1-3
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1E1-3
Maintenance and Repair . . . . . . . . . . . . . . 1E1-4
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1E1-4
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E1-4
Starting Motor . . . . . . . . . . . . . . . . . . . . . . . . 1E1-5
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E1-6
Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . 1E1-7
Ignition Cable . . . . . . . . . . . . . . . . . . . . . . . . 1E1-9
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . 1E1-12
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E1-12
SPECIFICATIONS
ALTERNATOR SPECIFICATIONS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
TABLE OF CONTENTS
Application
Output Voltage
Current
Resistance Between Rotor Core and Slip RingDescription
12 - 14 V
115 A
¥ W

1E1-2 M162 ENGINE ELECTRICAL
N·m
14 - 18
4 - 5
45 - 50
12 - 15
6 - 7
35 - 48
12 - 18
12 - 18
12 - 18
9 - 11
9 - 11
25 - 30
STARTING MOTOR SPECIFICATIONS
Application
Voltage
Output PowerDescription
12 V
1.7 KW
BATTERY SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application
Capacity
Specific Gravity
Max. Tolerance Between CellsDescription
75 AH
³ 1.24
³ 0.04
Application
Alternator Terminal B+Nut
Alternator Terminal D+Nut
Alternator Combinction Bolt
Battery Cable Nut on Starting Motor
Electric Wire Nut on Starting Motor
Starting Motor Mounting Nut
Battery Mounting Bracket Nut
Battery Negative Cable
Battery Positive Cable
Ignition Cable Cover Bolt
Ignition Cable Bolt
Spark plug

1E1-4 M162 ENGINE ELECTRICAL
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
ALTERNATOR
Preceding Work : Removal of the drivebelt
Removal & Installation Procedure
1. Disconnect the negative battery terminal.
2. Unscrew the nut and disconnect the terminal (1).
Installation Notice
1 Terminal (B+)
2 Terminal (D+)
3 Combination Bolt
4 Alternator
3. Unscrew the nut and disconnect the terminal (2).
Installation Notice
Tightening Torque 14 - 18 Nm
4. Unscrew the combination bolt (3).
Installation Notice
Tightening Torque 4 - 5 Nm
5. Remove the alternator.
6. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 42 - 50 Nm

M162 ENGINE ELECTRICAL 1E1-5
3 Fixing Bolt
4 Starting Motor
4. Unscrew the mounting bolts (3) of starting motor.
Installation Notice
5. Remove the starting motor.
6. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 35 - 48 Nm
STARTING MOTOR
Removal & Installation Procedure
1. Disconnect the ground cable.
2. Unscrew the nut and disconnect the battery cable(1).
Installation Notice
1 Battery Cable
2 Engine Electric Wire
3. Unscrew the nut and disconnect the engine electric wire
(2).
Installation Notice
Tightening Torque 12 - 15 Nm
Tightening Torque 6 - 7 Nm

1E1-6 M162 ENGINE ELECTRICAL
BATTERY
1 Cable Terminal (-)
2 Cable Terminal Cap (-)
3 Cable Terminal Cap (+)
4 Nut
5 Fuseblink Box
6 Terminal (+)7 Battery holddown Bracket
8 Battery Clamp Bolt
9 Battery
10 Sub Tray
11 Battery Tray
Removal & Installation Procedure
Notice
lDisconnect the battery negative cable first.
lInsert the clamp bolt (8) into the battery tray hole (11)
from inside when installing.

1E1-10 M162 ENGINE ELECTRICAL
Functions
1. Firing order : 1-5-3-6-2-4
2. The ignition cables are located on the cylinder head cover.
Each ignition coil provides the high voltage to two spark
plugs simultaneously.
- T1/1 : cylinder 2 and 5
- T1/2 : cylinder 3 and 4
- T1/3 : cylinder 1 and 6
Removal & Installation Procedure
1. Disconnect the negative battery cable (1).
2. Remove the ignition cable connector from the ignition cable.
3. Disconnect the secondary spark plug connectors from the
each spark plugs and remove the ignition cable.
Installation Notice 3. The secondary output voltage (5a) is supplied to the No.2
cylinder spark plug through the spark plug connector. The
secondary output voltage (5b) is supplied to the No.5 cylinder
spark plug through the ignition cable. The guide pin (W)
acts as a ground while the ignition cable is operated.
lMake sure that the ignition cables are correctly routed.
lExactly install the ignition cable guide pin into the vehicle
to be grounded.
4. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 9 - 11 Nm

1E1-12 M162 ENGINE ELECTRICAL
UNIT REPAIR
BATTERY
Inspection
Notice
lWhen charging the battery, do not leave the inflammable
objects around it.
lWhen checking the electrolyte of battery, put on
an eye protector and gloves.
1. Inspect the surface of the battery and replace if any defects
were found on it.
2. Check if the specific gravity of the electrolyte is within the
specified value.
Notice
lReplace the battery if the maximum tolerance of the
electrolyte between cells is out of the specified value.
lMeasure the specific gravity in the approx. 20°C
of ambient temperature.
3. Replenish the electrolyte if necessary.Battery capacity(Ah)
Battery specific gravity
Max. tolerance between cells85
³ 1.24
³ 0.04

SECTION 1E2
M161 ENGINE ELECTRICAL
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1E2-1
Alternator Specifications . . . . . . . . . . . . . . . . 1E2-1
Starting Motor Specifications . . . . . . . . . . . . 1E2-2
Battery Specifications . . . . . . . . . . . . . . . . . . 1E2-2
Fastener Tightening Specifications . . . . . . . . 1E2-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1E2-3
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1E2-3
Maintenance and Repair . . . . . . . . . . . . . . 1E2-4
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1E2-4
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E2-4
Starting Motor . . . . . . . . . . . . . . . . . . . . . . . . 1E2-5
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E2-6
Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . 1E2-7
Ignition Cable . . . . . . . . . . . . . . . . . . . . . . . . 1E2-9
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . 1E2-12
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E2-12
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
TABLE OF CONTENTS
SPECIFICATIONS
ALTERNATOR SPECIFICATIONS
Application
Output Voltage
Current
Resistance Between Rotor Core and Slip RingDescription
12 - 14 V
115 A
¥ W