1998 SSANGYONG MUSSO oil

1B1-54 M162 ENGINE MECHANICAL
Removal & Installation Procedure
1. Unscrew the stretch bolt.
Installation Notice
Sectional View
1 Oil Pan
2 Cover
3 Crankshaft Front Seal
4 Flywheel MTG Bolt
5 Crankshaft
6 Dowel Pin
7 Plate
8 TGCC
9 Bolt
10 Front Drive Plate
11 Rear Drive Plate
12 Rivet
13 Segment
14 Ring Gear
lReplace the bolt when the stretch side diameter (d) of
the flywheel mounting bolt is less than 8.0mm.
lFor the stretch bolt tightening, keep the socket wrench
and Tommy-bar to be 90° and tighten as specified.
2. Remove the flywheel for manual transmission vehicles, or
the driven plate (3), and plate (2) for Auto. transmission
vehicle.
3. Installation should follow the removal procedure in the
reverse order.Tightening Torque1st step 45+5 Nm
2nd step 90° + 10°

M162 ENGINE MECHANICAL 1B1-55
CAMSHAFT ADJUSTER
1 Bolt (M6 x 16, 3 pieces)........................ 9-11 Nm
2 Electromagnetic Actuator (2 Pin Connector)
3 Bolt........................................................... 35 Nm
4 Armature
5 Roll Pin
6 Nut (M20 x 1.5)....................................60-70 Nm
7 Front Cover
8 Seal
9 Camshaft Position Sensor
10 Bolt (M6 x 16, 2 pieces)......................... 9-11 Nm
11 Seal
12 Seal Cover13 Camshaft Sprocket and Position Indicator (b)
14 Adjuster piston
15 Flange bolt (M7 x 13, 3 pieces)
..............................................1st step 18-22 Nm
2nd step 90° ± 5°
16 Flange Shaft
17 Compression Spring
18 Control Piston
19 Circlip
20 Oil Gallery
21 Pin
22 Intake Camshaft

M162 ENGINE MECHANICAL 1B1-71
VALVE STEM SEAL
Preceding Work : Removal of valve spring
1 Drift (Special Tool)
2 Valve Stem Seal
3 Protective Sleeve
Drift 119 589 00 43 00 Pliers 104 589 00 37 00
Tools Required
104 589 00 37 00 Pliers
119 589 00 43 00 Drift
Replacement Procedure
1. Remove the valve stem seal (2) using the pliers.
Notice
Check the valve stem seal for damage and replace if
necessary.
2. Coat the valve stem seal with oil and assemble it with the
protective sleeve.
3. Insert the valve stem seal by pressing it with the drift.

1B1-72 M162 ENGINE MECHANICAL
CHAIN TENSIONER
1 Screw Plug................................................ 40 Nm
2 Seal
3 Filler Pin
4 Compression Spring5 Snap Ring
6 Thrust Pin
7 Chain Tensioner Housing.....................72-88 Nm
8 Seal
Removal Procedure
1. Position the No.1 cylinder to TDC (OT).
Notice
Remove the oil filler cap at adjustment position, and check
whether the intake camshaft cam’s lobe (arrow) stays in the
upper side.
2. Cover the alternator with a clean cloth.
3. Release the tension by unscrewing the screw plug once.
Notice
In case that the tension is reduced by unscrewing the screw
plug, reinstall after completely removing the chain tensioner.
If the chain tensioner is tightened again without completely
reducing its tension, then the detent spring doesn’t return
to the original position and the tension gets excedded.

1B1-74 M162 ENGINE MECHANICAL
4. Lightly apply the grease to the seal (2) and install the screw
plug (1).
Installation Notice
Sectional View
1 Screw Plug
2 Ball (Nonreturn Valve)
3 Compression Spring
4 Ball Guide
5 Seal (Aluminum)
6 Filler Pin
7 Compression Spring
8 Snap Ring
9 Thrust Pin
10 Ball (Nonreturn Valve)
11 Compression Spring
12 Thrust Piece13 Chain Tensioner Housing
1 4 Seal
15 Timing Gear Case Cover
16 Cylinder Head
17 Bolt / Washer
18 Tensioning Rail
19 Cylinder Head Gasket
20 Timing Chain
21 Tensioning Rail Base (Sliding Surface)
A Oil Supply Hole
B Chain Tensioner Oil Storage Hole 5. Check for leaks by operating the engine.
Tightening Torque 40 Nm

M162 ENGINE MECHANICAL 1B1-83
CRANKSHAFT SPROCKET
Preceding Work : Removal of oil pan
Removal of tensioning rail
Removal of crank case guide rail
6 Bolt (M8 x 20, 1 piece) / Washer..........29-35 Nm
7 Oil Pump Sprocket
8 Oil Pump
9 Oil Pump Roller Chain
10 Timing Chain 1 Oil Pump Chain Tensioner
2 Oil Pump Chain Bushing
3 Oil Pump Chain Spring
4 Crankshaft Sprocket
5 Key

1B1-84 M162 ENGINE MECHANICAL
Tools Required
615 589 01 33 00 Puller
Removal & Installation Procedure
1. Put the assembly mark at the crankshaft sprocket (4) and
the timing chain (10) with the paint (arrow).
Installation Notice
Align the assembly marks on cranshaft sprocket and timing
chain. Also, align the assembly marks on camshaft sprocket
and timing chain when installing.
2. Unscrew the bolt (6) and remove the oil pump sprocket (7)
from the oil pump.
Installation Notice
Puller (04) 615 589 01 33 00
3. Remove the oil pump roller chain (9).
4. Remove the oil pump chain tensioner (1), oil pump chain
bushing (2), and the oil pump chain spring (3).
5. Remove the crankshaft sprocket (4) using the puller (04,
special tool).
Notice
lMake sure not to lose the crankshaft pulley key(5) when
removing.
lInstall the crankshaft sprocket(4) after warming it up.
6. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 29 - 35 Nm

M162 ENGINE MECHANICAL 1B1-85
PISTON
Preceding Work : Removal of engine
Removal of cylinder head
Removal of oil pan
Removal of oil pump
Removal of baffle plate
1 Connecting Rod Bearing Cap
2 Connecting Rod
3 Connecting Rod Bolt (M9 x 52, 12 pieces)
....................................................1st step 40 Nm
2nd step 90° + 5°4 Piston
5 Snap Ring
6 Piston Pin