1998 NISSAN GT-R battery

ANTI-LOCK BRAKE SYSTEM
CONSULT (Cont'd)
DATA MONITOR MODE
MONITOR ITEM I CONDITION
FR RH SENSOR
FR
LH SENSOR
RR SENSOR Drive vehicle.
(Each wheel is rotating.)
STOP LAMP SW Turn
ignition switch ON and
depress brake pedal.
FR RH
IN SOL
FR RH OUT SOL
FR
LH IN SOL
FR LH OUT SOL
REAR IN SOL
REAR OUT SOL Ignition
switch is turned ON or
engine is running.
ACTUATOR RLY
MOTOR RLY
Ignition switch is turned ON or
engine is running.
WARNING LAMP
BATTERY VOLT
I
VOLTAGE Indicates
the voltage mea-
sured with a voltage probe.
PLS WIDTH-H
I
Refer to CONSULT Instruction
Manual.
NlSSAN
CONSULT
START I --
1 SUB MODE BR455C
$ SELECT SYSTEM 0-
ENGINE
A/T
I - ABS I
SPECIFICATION
Displays computed vehicle speed from wheel sensor signal.
Almost the same speed as speedometer.
Depress the pedal: ON
Release the pedal: OFF
EC ;
Operating conditions for each solenoid valve are indicated. ABS is AT '
not operating: OFF
Displays ON/OFF condition of ABS actuator relay.
When turning ignition switch ON,
ABS actuator relay
is operated. 2
ABS is not operating: OFF
ABS
is operating: ON
Warning lamp is turned on: ON
R8 $
Warning lamp is turned off: OFF
Power supply voltage for control unit
~~~~
ACTIVE TEST PROCEDURE
When conducting Active test, vehicle must be stationary.
Confirm that brakes have been bled completely.
When ABS warning lamp stays on, never conduct Active test.
Turn ignition switch OFF.
Connect CONSULT to Data Link Connector for CONSULT.
Start engine.
Touch "START' on CONSULT screen.
Touch
"ABS".

TCSIABS SYSTEM
Control Unit
InputlOutput Signal Specifications
USING CIRCUIT TESTER
TCS/ABS control unit - -
To perform the following inspection, the ignition switch should be turned ON with TCS/ABS control unit con-
nector and actuator connector properly connected.
I
TCS/ABS contro! unit connector
Terminal No.
P Front right wheel I
Item
sensor
I
Specifications'l
Rear right wheel Wheels are turning (Approx.
30 km/h)'3: Pulse generates.
Front: Approx. 200
Hz
Rear: ADDrox. 200 Hz I . , sensor
Rear left wheel
sensor
I
I
Brake pedal is depressed: Battery voltage (Approx. 12V)
Stop lamp signal Brake pedal is not depressed: Less than approx. 2V
Actuator relay is activated (with engine running): Less than approx.
2V
Actuator relay Actuator relay
is not activated (with fail-safe function activated and engine
not running): Battery voltage (Approx.
12V)
ABS motor is running (in CONSULT active test mode): Battery voltage
ABS motor monitor (Approx. 12V)
ABS motor is stopped (with ignition switch ON): Approx. OV
SLIP
indicator
SLIP
indicator lamp
ON'S: OV
lamp
SLIP
indicator lamp
OFF'5: Battery voltage (Approx. 12V)
TCS OFF indicator TCS OFF indicator lamp
ON'4: OV
lamp TCS OFF indicator lamp
OFF'4: Battery voltage (Approx. 12V)
TCS OFF switch TCS OFF switch is pressed: Approx. OV
signal TCS OFF switch is not pressed: Approx. 4
- 5V
Engine speed sig-
nal Pulse generates.
Refer to EC section
("ECM.TCM Input/Outout Reference Value")
Total control signal
(Multiple communi-
cation) for engine,
A/T and TCSIABS Check item (Refer-
ence)
Wheel sensors
and circuit Stop lamp switch
and circuit
ABS actuator relay
and circuit
ABS motor monitor
circuit
SLlP indicator
lamp and circuit
TCS OFF indicator
lamp and circuit
TCS OFF switch
and circuit
Engine speed sig-
nal circuit
Circuit for total
control signal (Mul-
tiple communica-
tion) for engine, A/T and TCSIABS

TCS/ABS SYSTEM
Control Unit InputlOutput Signal Specifications
(Cont'd)
Terminal No.
Specifications'l
- - --
Check item (Refer-
ence)
- - -
Body
ground
-
Approx. 7V - - or higher Communication
line circuit between
TCSIABS control
unit and throttle
control unit
DKV
(throttle angle
output)
Acceleration pedal is released: approx. 1 ms (reference)
ABS warning lamp ABS warning
lamp
and circuit 4B3 warning lamp 0Nr2: Approx. OV
4BS
warning lamp 0FF72: Battery voltage (Approx. 12V)
cictuator
relay is activated (with engine running): Battery voltage
(Approx.
12V)
ktuator
relay is not activated (with fail-safe function activated and engine
70t
running): Approx.
OV
ABS warning lamp
and circuit,
ABS
actuator relay and
circuit
Actuator relay
monitor
48s
motor is running (in
CONSULT active test mode): Less than approx.
2V
4BS motor is stopped: Battery voltage (Approx. 12V)
TCS is not activated: ABS
motor, motor
relay and circuit
ABS
motor relay
Approx. 7V - -
OV I I Communication
line circuit between TCSfABS control
unit and throttle
control unit
DKR
(throttle
motor target angle
signal) Approx. 9 ms (Reference)
Front
right inlet
solenoid
Front right outlet
solenoid
4ctuator
is activated (in CONSULT active test mode), or actuator relay is
lot
activated (with fail-safe function activated and engine not running):
4pprox.
OV
4ctuator
is not activated and actuator relay is activated (with vehicle
stopped and engine running): Battery voltage (Approx.
12V)
Rear inlet solenoid
Rear outlet
sole- ABS solenoid and
circuit
Front left inlet
solenoid
Front left outlet
solenoid
Battery gnition switch
ON: Baitery voltage
(Approx. 12V) Control
unit power
supply circuit
'1: Do not force to oDen a connector terminal when usina a circuit tester for ins~ection. '2: ABS warning lamp ON: When the ignition switch is t6ned ON (before startirig the engine) or a malfunction is detected
ABS warning lamp OFF: When the engine has started (with the system in normal condition)
'3: Tire pressure must be in accordance with specification. '4: TCS OFF indicator lamp ON: When the ignition switch is turned ON (before starting the engine), a malfunction is detected,
or TCS OFF switch is turned ON TCS OFF indicator lamp OFF: When the engine has started (with the system in normal condition) and the TCS OFF switch
is off '5: SLlP indicator lamp ON: When the ignition switch is turned ON (before starting the engine) or a malfunction is detected
SLlP
indicator lamp OFF: When the engine has started (with the system in normal condition) and the TCS is inoperative

TCS/ABS SYSTEM
Control
Unit InpuVOutput Signal Specifications
(Cont'd)
Throttle control unit
Terminal No.
Specifications*
item Check
item (Refer-
ence)
Throttle angle sig-
nal Ignition switch
ON
Throttle valve is fully closed: Approx.
0.5V
Throttle valve is fully open: Approx.
4.2V
Throttle motor sen-
sor
Throttle motor angle signal Throttle
position
sensor circuit and
ECM
I
Throttle motor sen-
sor and circuit R8 Engine is idling: Approx. 4.4V
I
I Throttle motor
TCS switch signal Engine
is idling: Approx.
3.4V
lgnition switch ON: Approx. 5V
Throttle control
unit power supply angle
signal and
MA
circuit
TCS switch signal
circuit
EL
Body
jround
- - -- -- - - - --
lgnition switch ON: Battery voltage (Approx. 12V)
Throttle control
unit power supply
Throttle motor relay
Sensor battery
voltage
Throttle control
unit power supply
Throttle motor relay Throttle
control
unit power circuit @J
1
Throttle control
unit power circuit
lgnition switch
ON: Battery voltage (Approx.
12V)
Throttle motor relay and circuit
lgnition
switch ON: Approx.
OV
Throttle position
sensor power cir-
cuit
lgnition
switch ON: Approx. 5V
lgnition switch ON: Battery voltage (Approx. 12V) Throttle control
unit power circuit
lgnition switch ON: Battery voltage (Approx. 12V)
I
Throttle motor
relay
and circuit
Start signal lgnition
switch START (Disconnect ECM-TCM connector or ECM connec-
tor.): Approx.
10V
*: Do not force to open a connector terminal when using a circuit tester for inspection. Start
signal circuit
and ECM

TCSlABS SYSTEM
Precautions for Trouble
Diagnosis
After performing trouble diagnosis, be sure to erase trouble stored in memory.
Refer to "CONSULT for
TCS/ABS Control Unit Control System"
(BR-27), "Self-diagnosis for TCSIABS
Control Unit Control System"
(BR-34), "CONSULT for Throttle Control Unit Control System" (BR-37) or
"Self-diagnosis for Throttle Control Unit Control System"
(BR-41).
The concerns that are difficult to duplicate may be caused by faulty electrical connections. Move harnesses
or harness connectors by hand to check if there is any poor mating of connector halves or faulty connec-
tion. Do not force to open a connector terminal when using a circuit tester for inspection.
Read GI section thoroughly in advance and make sure of all the general precautions.
Basic Inspection
BASIC INSPECTION 1 - Brake fluid level and leakage
1. Check brake fluid level in reservoir tank. Replenish brake fluid if necessary.
2. Check for leakage at or around brake piping and ABS actuator. If leakage or seepage is noted, proceed
as follows:
If ABS actuator connectors are loose, tighten to specified torque. Recheck to ensure that leakage is no
longer present.
If flare nut threads at piping connectors or actuator threads are damaged, replace faulty parts with new
ones. Recheck to ensure that leakage is no longer present.
If brake fluid leaks through areas other than actuator connectors, wipe off using a clean cloth. Recheck
for leakage or seepage. If necessary, replace faulty parts with new ones.
If brake fluid leaks at or seeps through ABS actuator, wipe off using a clean cloth.
Recheck for leakage or seepage. If necessary, replace ABS actuator with new one.
CAUTION:
ABS actuator cannot be disassembled. Do not attempt to disassemble it.
3. Check brake disc rotors and pads for proper operation.
BASIC INSPECTION 2 - Loose power line terminal
Check battery terminals (positive and negative) and battery mounting (ground) for looseness. If necessary,
tighten to specified torque. Check the battery for lower voltage.
BASIC INSPECTION 3 - SLlP indicator lamp, TCS OFF indicator lamp and ABS warning
lamp
Turn ignition switch "ON" to ensure that TCS OFF indicator lamp lights up. If TCS OFF indicator lamp does
not light, check TCS OFF indicator lamp circuit.
Turn ignition switch
"ON" to ensure that SLlP indicator lamp lights
up. If SLlP indicator lamp does not light,
check SLlP indicator lamp circuit.
Turn ignition switch "ON" to ensure that ABS warning lamp lights up. If ABS warning lamp does not light,
check ABS warning lamp circuit.
Check that the SLlP indicator lamp and the ABS warning lamp go off approx.
1 second after the engine
has started. If either of the lamps still remains on, perform the self-diagnosis for TCSIABS control unit
control system and the self-diagnosis for throttle control unit control system.
After driving vehicle at approx. 30
km/h
for approx.
1 minute, check to ensure that the SLlP indicator lamp
and the ABS warning lamp are off. If either of the lamps still remains on, perform the self-diagnosis for
TCS/ABS
control unit control system and the self-diagnosis for throttle control unit control system.
Check that the TCS OFF indicator lamp turns ON and OFF when the TCS OFF switch is turned to
ON
and OFF respectively, with the engine running. If the lamp status does not correspond to the switch
position, check the TCS OFF switch circuit.
Check that the TCS OFF indicator lamp goes off when the engine has started with the TCS OFF switch
OFF. If the TCS
OFF indicator lamp does not go off even 10 seconds after the engine has started, per-
form the self-diagnosis for TCSIABS control unit control system and the self-diagnosis for throttle control
unit control system.
After driving vehicle at approx.
30 kmlh for approx. 1 minute with the TCS OFF switch OFF, check to ensure
that the TCS OFF indicator lamp is off. If the TCS OFF indicator lamp lights up, perform the
self-diagno-
sis for
TCS/ABS
control unit control system and the self-diagnosis for throttle control unit control system.
After performing self-diagnosis procedures, be sure to erase trouble stored in memory.

TCS/ABS SYSTEM
CONSULT for TCS/ABS Control Unit Control
System (Cont'd)
SELF-DIAGNOSTIC RESULTS MODE
Diagnostic item Diagnostic item is detected when ...
Circuit for front right wheel sensor is open. Or an abnormally high input voltage is
entered due to short to battery.
Circuit for front left wheel sensor is open. Or an abnormally high input voltage is entered
due to short to battery.
Circuit for rear right wheel sensor is open. Or an abnormally high input voltage is enterec
due to short to battery. Check
item
FR RH SENSOR
[OPEN]
FR LH SENSOR
[OPEN]
REAR SENSOR
[OPEN]
RR LH SENSOR
[OPEN] Circuit for rear left
wheel sensor is open. Or an abnormally high input voltage is entered
due to short to battery.
Front right wheel sensor is short-circuited or shorted to ground, or gap between the
wheel sensor and the sensor rotor is large. An abnormally low input voltage is entered
and input signal is abnormal.
FR
RH SENSOR
[SHORT) Wheel
sen-
sor circuit
FR LH SENSOR
[SHORTJ Front
left wheel sensor is short-circuited or shorted to ground, or gap between the wheel
sensor and the sensor rotor is large. An abnormally low input voltage is entered and
input signal is abnormal.
Rear right wheel sensor is short-circuited or shorted to ground, or gap between the
wheel sensor and the sensor rotor is large. An abnormally low input
vottage is entered
and input signal is abnormal.
Rear left wheel sensor is short-circuited or shorted to ground, or gap between the wheel
sensor and the sensor rotor is large. An abnormally low input voltage is entered and
input signal is abnormal.
Circuit for front right inlet ABS solenoid valve is open, or an output voltage is much lower
than the specified value due to short to ground.
Circuit for front
left inlet ABS solenoid valve is open, or an output voltage is much lower
than the specified value due to short to ground.
RR
RH SENSOR
[SHORTJ
RR LH SENSOR
[SHORV
FR RH IN ABS SOL
[OPEN]
FR LH
IN ABS SOL
[OPEN]
REAR IN ABS SOL
[OPEN] Circuit
for rear inlet ABS solenoid valve is
open, or an output voltage is much lower than
the specified value due to short to ground.
-
FR RH IN ABS SOL
[SHORT]
- - - -- - - - -
Circuit for front right inlet ABS solenoid valve is shorted, or an output voltage is much
higher than the specified value due to short to battery.
Circuit for front left inlet ABS solenoid valve is shorted, or an output voltage is much
higher than the specified value due to short to battery.
Circuit for rear inlet ABS solenoid valve is shorted, or an output voltage is much higher
than the specified value due to short to battery.
Circuit for front right outlet ABS solenoid valve is open, or an output voltage is much
lower than the specified value due to short to ground.
Circuit for front left outlet
ABS solenoid valve is open, or an output voltage is much lower
than the specified value due to short to ground.
FR
LH IN
ABS SOL
[SHORTJ
REAR IN ABS SOL
[SHORT] Solenoid and
circuit
FR RH OUT ABS SOL
[OPEN]
FR LH OUT ABS SOL
[OPEN]
REAR
OUT ABS SOL
[OPEN]
- --
Circuit for rear outlet ABS solenoid valve is open, or an output voltage is much lower
than the specified value due to short to ground.
Circuit for front right outlet ABS solenoid valve is shorted, or an output voltage is much
higher than the specified value due to short to battery.
Circuit for front left outlet
ABS solenoid valve is shorted, or an output voltage is much
higher than the specified value due to short to battery.
Circuit for rear outlet
ABS solenoid valve is shorted, or an output voltage is much higher
than the specified value due to short to battery.
ABS motor turns ON when control unit sends OFF signal. ABS motor circuit is open or
shorted to ground.
ABS motor turns OFF when control unit sends ON
signzl. Relay control wire is broken.
FR RH OUT ABS SOL
[SHORT]
FR LH OUT ABS SOL
[SHORT]
REAR
OUT ABS SOL
[SHORT]
ABS MOTOR
[ON FAILURE]
ABS motor,
motor relay
and circuit
ABS
MOTOR
[OFF FAILURE]

TCS/ABS SYSTEM
CONSULT
for TCSlABS Control Unit Control
System
(Cont'd)
Diagnostic item Check item
Diagnostic
item is detected when ...
ABS ACTUATOR RELAY
b~ FAILURE] ABS
actuator relay turns ON when control unit sends OFF signal. Actuator relay is short-
circuited to ground. ABS
actuator
relay and
circuit
ABS
ACTUATOR RELAY
[OFF FAILURE] ABS
actuator relay turns OFF when control unit sends ON signal. Relay control wire is
broken.
BAlTERY VOLTAGE
[VB-IiIGH] TCSIABS
control unit
power supply
and ground
circuit
TCSIABS
control unit battery voltage is abnormally high.
BAlTERY VOLTAGE
[VB-LOW TCSIABS control unit battery voltage is abnormally low.
- -
Function of calculation in TCS/ABS control unit has failed. TCSIABS
control unit
CONTROL
UNIT
ABS motor,
motor relay and circuit
ABS
MOTOR
[LOCK FAILURE] ABS
motor speed is abnormally low.
Engine speed signal is interrupted or signal wire is suspected to be broken.
TCSIABS control unit connector or ECM-TCM or ECM connector is poorly connected. Engine
speed signal circuit
ENGINE
SPEED SIG
Circuit for
the commu-
nication line
between
TCSIABS
control unit
and throttle control unit
The communication line between TCSIABS control unit and throttle control unit is open
or shorted.
Throttle control system (throttle control unit, peripheral harness, and throttle actuator)
is abnormal.
TCSIABS control unit or throttle control unit battery voltage is low.
THROTLE
POSl
SIG
Engine main components (crankshaft position sensor, mass air flow sensor, engine cool-
ant temperature sensor, ignition primary signal, throttle position sensor, and motor throttle
position sensor) are abnormal. Engine sys-
tem
ENGINE SYSTEM
Total control
signal
1
(multiple sig- nal) for
engine,
A/l
and TCSI
ABS
Total control signal (multiple signal) for engine, AIT and TCS/ABS is abnormal (open or
shorted communication harness, faulty connections, abnormal
TCS/ABS control unit or
ECM-TCM or ECM).
TCSIABS control unit power is momentarily cut off or decreased.
LAN
SIGNAL
1
Total control signal (multiple signal) for engine,
and TCS/ABS is abnormal (open or
shorted communication harness, faulty connections, abnormal
TCS/ABS control unit or
ECM.TCM or ECM).
ECM.TCM or ECM starter switch is stuck to ON.
The starter switch is ON for 10 seconds or longer even after the engine has started.
(This is not
a malfunction.)
ECM-TCM or ECM is abnormal. (Total control signal (multiple signal) for engine,
A/T
and TCSIABS is malfunctioning. Or the system is in the process of CPU back up.)
TCSIABS is abnormal. Total
control
signal
2
(multiple sig-
nal) for
engine,
PA
and TCSI
ABS
LAN
SIGNAL
2
LAN SIGNAL 3

TCS/ABS SYSTEM
CONSULT
for TCSfABS Control Unit Control
System (Cont'd)
DATA MONITOR MODE --
I ~elect-monitor item I
Display
signals Selection from
Remarks
menu
FR RH SEN
[kmlh] Displays vehicle speed computed based on
front right wheel sensor signal.
zc
FR LH SEN [kmlh] Displays
vehicle speed computed based on
front left wheel sensor signal.
AT
Displays vehicle speed computed based on
rear right wheel sensor signal.
Displays vehicle speed computed based on
rear left wheel sensor signal.
REAR
SEN
[kmlhll
RR LH SEN
lkmlhll
FIR IN SOL [ON-OFF]
I O
FIR OUT SOL [ON-OFF] /
lndicates operating condition (ONIOFF) for 87 front right inlet solenoid.
lndicates operating condition (ONIOFF) for
front right outlet solenoid.
Rs
FIL IN SOL O
A FIL OUT SOL [ON-OFF] /
lndicates operating condition (ONIOFF) for
front left inlet solenoid.
y- 13 u -:-.!
Indicates operating condition (ONIOFF) for
1 front left outlet solenoid. --
REAR IN SOL [ON-OFq / A I Indicates operating condition (ONIOFF) for
" I rear inlet solenoid.
RR OUT SOL [ON-OFF]
/
ABS ACTUATOR [ON-OFF]
- - .
O
O
0
0
ABS MOTOR [ON-OFFI I - I 0
-
lndicates operating condition (ONIOFF) for SC rear outlet solenoid.
lndicates ABS actuator relay status
(ON1
OFF). Indicates
ABS motor relay status
(ONIOFF).
Indicates stop lamp switch status
(ONIOFF).
STOP LAMP SW
[ON-OFFl
I 0 I 0
ENG SPEED SIG [RUNISTOP] I 0 I 0 0 I lndicates engine operation.
WARNING LAMP
[ON-OFF]
I - I 0 0 I lndicates ABS warning lamp status.
BATTERY VOLT
iv I
I lidicates the voltage supplied to the TCSI n
THRTL OPENING 1x1 1 0 I 0
V
0
THL OP TARGET [%I I - 1 0
ABS control unit.
Indicates throttle angle condition.
- - -
lndcates throttle control unit target angle. 0-1- -- - -- - -
lndicates the value at which fuel to ECM is
cut off.
lndicates the gear position.
lndicates TCS switch status (ONIOFF).
TCS
MODE
GEAR
1016-
0 I lndicates TCS OFF indicator lamp status.
TCS
SW [ON-OFF]*
TCS OFF LAMP [ON-OFF]
SLIP
LAMP [ON-OFF]
0 I lndicates SLlP indicator lamp status.
I I
*: The TCS switch only indicates that the switch is ON or OFF. It does not necessarily correspond to the TCS operation condi-
tion (TCS OFF indicator lamp OFF or ON).
-
0
-
-
lndicates the selector position (ONIOFF)
based on the
A/T PNP switch signal or the
neutral position switch signal.
-
0
0
0
PIN POSl SIG
[ON-OFFI
I