1998 JAGUAR X308 oil

I
nstallation


11
.
Remove the crankshaft front seal.
1. Install and tighten the removal tool 303-541 to the crankshaft front seal.
2. Tighten the centre bolt of the tool to extract the seal.
R
emove the tool an
d seal assembly.
Separate the seal
from the tool.
12. Very carefully clean the thread s of the crankshaft, using a
plug tap M16x2, to remove all old cured sealant.
Kee
p the tap horizontal. Do not enlarge the crankshaft
thread - remove sealant only.
13. Clean all relevant parts and faces.

1. Loc
ate the new oil seal into the timing cover.
1. Remove the transit ring from the oil seal.
2. Position the seal to the timing cover.

2. Inst
all the new oil seal to the timing cover.
1. Install oil seal replacer tool 303-542 to the oil seal.
2. Use the nut and bolt provided with the tool, to fully seat the seal to the timing cover. Only tighten the nut
sufficiently to locate the seal and no more, or the
timing cover could become distorted.
All
ow the tool to stay in posi
tion against the seal for at
least five seconds.
R
emove the special tool from the seal.

1.
Locate the new oil seal into the timing cover.
1. Remove the transit ring from the oil seal.
2. Position the seal to the timing cover.
2.
Install the new oil seal to the timing cover.
1. Install oil seal replacer tool 303-542 to the oil seal.
2. Use the nut and bolt provided with the tool, to fully seat the seal to the timing cover. Only tighten the nut sufficiently to locate the seal and no more, or the timing cover could become distorted.
 Allow the tool to stay in position against the seal for at least five seconds.
 Remove the special tool from the seal.
3. If the damper is not to be installed immediately, the transit ring should be installed temporarily to the seal.
Installation

Engine - Crankshaft
Rear Seal4.0L
NA V8 - AJ27/3.2 L NA V8 - AJ26
In-v
ehicle Repair
Remov

al
S
pecial Tool(s)
Crankshaft Rear Oi

l Seal Remover /
Replacer.
303 - 538
1. Open the engine compartment and fit paint protection sheets.

2. Di
sconnect the batt
ery ground cable.
R
emove the battery cover.
3. Remove the transmission. Refer to Operation 44.20. 01 in
Section 307-01A.
4. Remove the drive plate. Refer to Operation 12.53.13.

5. F
it and align the seal removal tool 303 - 538 to the crankshaft.
1. Unscrew the two nuts towards the head of each bolt to allow the bolts to fit fully into the crankshaft.
2. Unscrew the center bolt until it is below the face of the main tool and position the tool to the rear of the
crankshaft.
3. Lightly tighten the two bolts so that they fully locate in the crankshaft.

6. Hold the tool against th
e cran
kshaft and lightly and evenly
tighten the two nuts to the face of the tool; to secure the tool
and to hold it parallel to the face of the crankshaft.
7. Secure the oil seal to the tool using the three self-tapping

Engine - Crankshaft Rear Seal4.0L SC V8 - AJ26
In-vehic
le Repair
Remov
a
l
S
p
ecial Tool(s)
Crankshaft Rear Oi
l Seal R
emover /
Replacer.
303 - 538
1. Open the engine compartment and fit paint protection sheets.

2. Disc
onnect the batt
ery ground cable.
Re
move the battery cover.
3. Remove the transmission. Refer to Operation 44.20. 01 in
Section 307-01B.
4. Remove the drive plat e. Refer to Operation (SC) 12.53.13.

5. Fi
t and align the seal removal tool 303 - 538 to the crankshaft.
1. Unscrew the two nuts towards the head of each bolt to allow the bolts to fit fully into the crankshaft.
2. Unscrew the center bolt until it is below the face of the main tool and position the tool to the rear of the
crankshaft.
3. Lightly tighten the two scre ws so that they fully locate
in the crankshaft.

6. Hold the tool against th e cr
an
kshaft and lightly and evenly
tighten the two nuts to the face of the tool; to secure the tool
and to hold it parallel to the face of the crankshaft.
7. Secure the oil seal to the tool using the three self-tapping

E
ngine - Cylinder Head LH
In-ve
hicle Repair
Remova

l
CAU
TION: If a replacement cylinder head is to be installed to a
vehicle with variable camshaft timing (VCT) the cylinder head m ust have the
oil gallery blind rivet removed before installation.
Spe
cial Tool(s)

Cams

haft setting
303-530

Ti
ming chain tensioning
303-532

Wedges, prim
ary chain
303-533

Cr
ankshaft setting
303-531
1.
Open the engine compartment and install paintwork protection sheets.
2. Set the engine compartment cover to the service access position.

3.
Disconnect the battery ground cable.
Re

move the battery cover.
4. Remove the engine fron cover.For additional information, refer to: Engine
Front Cover (303-01 Engi
ne, In-vehicle Repair).
5. Remove the Inlet Manifold. Refer to Operation 30.15.01 in this Section. This operation includes depressurising the fuel system and removing the throttle
housing.
6. Disconnect the hoses and multi-plug from the coolant outlet pipe.
1. Release and reposition the hose clip, and disconnect the heater hose.
2. Disconnect the multi-plug from the temperature sensor.
3. Release and reposition the hose clip along the bypass hose.

7.
Remove the coolant outlet pipe.
1. Remove the four bolts which secure the outlet pipe.
2. Remove the outlet pipe from the bypass hose and from the cylinder heads.
8. Remove and discard the sealing ring s from the outlet pipe grooves.

9.
Remove the nuts which secure the catalytic converter to the B-Bank
exhaust manifold flange.

10 . Re
move the VVT bush carrier.
1. Remove the two bolts and one nut which secure the carrier to the cylinder block.
2. Release the carrier from the two ring dowels and remove it.

11. R
emove the seals from the bush carrier.
1. Remove the sealing ring (scarf jointed) from the carrier bush groove.
2. Remove the O-ring from the carrier oil-way recess.
12. Raise the vehicle on a ramp.
13. Remove the crankshaft position sensor.

Inst
allation
Cl
ean the gasket faces of the catalyst and the exhaust manifold.
38. Clean cylinder head and cylinder block gasket faces.
E
nsure that all threaded holes in the cylinder block face are clean and
free from oil.
Cl
ean and inspect the cylinder head bolts. They may be re-used on two
occasions. When re- used, each bolt head should be marked with one
dot from an automatic centre punch.
39. Clean and inspect all relevant components and mating faces.

1.
CAUTIONS:
If a replacement cylinder head is to be installed to a vehicle with VCT
the cylinder head must have the oil gallery blind rivet removed before
installation.
Make sure that all debris is removed from the cylinder head and cylinder
head oil gallery.
Vehicles fitted with VCT: Remove the blind rivet from the VCT oil gallary.
• NOTE: The centre bore of the blind rivet is 6 mm diameter.
I
dentify the VCT oil supply gallery and the 8 mm blind rivet.
U

sing a suitable 3 mm punch release the centre of the blind rivet until
it is released from the outer part of the blind rivet.
U
sing a suitable extraction tool, remo
ve the remaining part of the blind
rivet.
2.
Clean the component mating faces.

3.
Check cylinder head face for distortio
n, across the center and from corner
to corner.

15
.
Connect the plug to the engine position sensor, at the rear of the cylinder
head.

16
.
Install the tappet and shim assemblies.
Lu
bricate each tappet assembly.
1. Install each tappet and shim asse mbly to its previously identified
position in the cylinder head.

17
.
Apply oil (EP-90) to the camshaft and bearing surfaces, as follows:
To th
e upper face of each bearing surface (two places) in the cylinder
head.
To th
e upper face of each bearing surface (two places) in each bearing
cap.
On
the cam lobes ONLY, not on the base circle area.
18. Install the camshafts.
1. Install the camshafts to position in the cylinder head, with the timing flats uppermost.