1998 JAGUAR X308 Drive shaft

6. Tigh
ten the exhaust camshaft
sprocket securing bolt.
1. Fit the chain tensioner tool 303 - 532 to the sprocket holes.
Appl
y force to the tool in an
anti-clockwise direction to
tension the chain on its drive side.
2. Whilst applying the opposing force to the sprocket and chain, tighten the sprock et securing bolt to 115 -
125 Nm.

7. Tigh
ten the VVT unit securing bolt.
1. Whilst still applying the opposing force to the
sprocket and chain (using 303 - 532), check that the
wedges are still in place, tighten the VVT unit
securing bolt to 115 - 125 Nm.
R
emove the chain tensioning
tool and the wedge(s).
8. Remove the camshaft locking tool 303 - 530.
9. Raise the vehicle on the ramp.
10. Remove the crankshaft setting tool 303 - 531.

11
.
Refit the crankshaft position sensor.
1. Fit the sensor to the fl ywheel housing and fit the
securing bolt. Tighten to 8-12 Nm.
2. Refit the access grommet to the housing.
12. Lower the ramp.
13. Fit new seals to the VVT bush carrier.
1. Fit the new sealing ring (scarf jointed) to the carrier bush groove.

Engine - Cr
ankshaft
Pulley4.0L NA V8 - AJ 27/3.2L NA V8 - AJ26
In-v
ehicle Repair
Remov

al
S
pecial Tool(s)

Cr

ankshaft locking, main tool
303-191

Adaptor

303-191-02

Crankshaft front
seal remover
303-541

Crankshaft front seal replacer
3
03-542

Crankshaft pull

ey/damper remover
303-588
1. Open the engine compartment and fit paintwork protection
sheets.
2. Set the engine compartment cover to the service access
position.
3. Remove the drive belt from the fro nt accessory drive. Refer to
Operation 12.10.40.
4. Remove the twin fan and motor assembly for access. Refer to
Operation 26.25.12
5. CAUTION: Under no circumstan ces should the crankshaft
setting peg 303-531 be used in the following operations, to lock
the crankshaft.
• NOTE: Should extra locking of the crankshaft be required, use a
lever against one torque converte r boss. Remove the plastic mesh
cover from the torque converter housing for access.

3.
If
the damper is not to be installed immediately, the transit
ring should be installed temporarily to the seal.

4. Install a new O-ri
ng seal to the damper.

5. Instal
l the crankshaft damper.
Apply petroleum jelly to the damper

bore and O-ring seal.

1. Install the damper onto the crankshaft.
2. Install the split locking ring onto the crankshaft,
inside the centre bo re of the damper.
3. Install, but do not tigh ten, a new damper securing
bolt.

6. CAUTIO
N: Under no circumstan
ces should the crankshaft
setting peg 303-531 be used in the following operations, to lock
the crankshaft.
Tighten the damper securing bolt. 1. Reposition the damper to allow access to the bolt holes for installing the locking tool.
2. Install the locking tool (303-01 and 303-01-02) to the
damper using the bolts provided.
3. Fully tighten the damper securing bolt to 364-386 Nm.
7. Re
move the locking tool from the damper.
8. Install the drive belt to the fr ont accessory drive. Refer to
Section 303-05.
9. Install the twin fan and motor assembly. Refer to Section 303-
03.
10. Install the plastic mesh cove r to the torque converter
housing; if removed for acce ss to lock the crankshaft.
11. Reset the engine compartment cover to the normal position
and connect the gas struts.
12. Remove the paintwork protection sheets and close the engine
compartment.

Cr
ankshaft front seal remover
303-541
Cr
ankshaft front seal replacer
303-542
Cr
ankshaft pulley/damper remover
303-588
Removal
1. Open the engine compartment and fit paintwork protection sheets.
2. Set the engine compartment cover to the service access position.
3. Remove the supercharger drive belt. Refer to Operation <<18.50.08>>.
4. Remove the drive belt from the front accessory drive. Refer to Operation <<12.10.40>>.

6.

CA
UTION:
Under no circumstances should the crankshaft setting peg 303-531 be used in the following
operations, to lock the crankshaft.
Tighten the damper securing bolt. 1. Reposition the damper to allow access to the bolt holes for installing the locking tool.
2. Install the locking tool (303-191 and 303-191-03) to the damper using the bolts provided.
3. Fully tighten the damper securing bolt to 364-386 Nm.
7. Remove the locking tool from the damper.
8. Install the drive belt to the front accessory drive. Refer to Operation <<12.10.40>>.
9. Install the supercharger drive belt. Refer to Operation <<18.50.08>>.
10. Install the twin fan and motor assembly. Refer to Section 303-03.
11. Install the plastic mesh cover to the torque converter housing; if removed for access to lock the
crankshaft.
12. Reset the engine compartment cover to the normal position and connect the gas struts.
13. Remove the paintwork protection sheets and close the engine compartment.

Engine - Crankshaft
Rear Seal4.0L
NA V8 - AJ27/3.2 L NA V8 - AJ26
In-v
ehicle Repair
Remov

al
S
pecial Tool(s)
Crankshaft Rear Oi

l Seal Remover /
Replacer.
303 - 538
1. Open the engine compartment and fit paint protection sheets.

2. Di
sconnect the batt
ery ground cable.
R
emove the battery cover.
3. Remove the transmission. Refer to Operation 44.20. 01 in
Section 307-01A.
4. Remove the drive plate. Refer to Operation 12.53.13.

5. F
it and align the seal removal tool 303 - 538 to the crankshaft.
1. Unscrew the two nuts towards the head of each bolt to allow the bolts to fit fully into the crankshaft.
2. Unscrew the center bolt until it is below the face of the main tool and position the tool to the rear of the
crankshaft.
3. Lightly tighten the two bolts so that they fully locate in the crankshaft.

6. Hold the tool against th
e cran
kshaft and lightly and evenly
tighten the two nuts to the face of the tool; to secure the tool
and to hold it parallel to the face of the crankshaft.
7. Secure the oil seal to the tool using the three self-tapping

3.
F
it the tool to the crankshaft.
E

nsure that the cent
re bolt is unscrewed to below the face
which is to fit to the crankshaft and position the tool to the
crankshaft.
Chec
k that the nuts are fully unscrewed and enter the two
bolts to the crankshaft thre ads and lightly tighten.

4. Tigh
ten the nuts, finger tight, to hold the tool assembly against

the seal. Check that the seal and the tool are approximately
parallel to the rear of the engine.

5. Pres
s the seal into the housing.
Ho

ld each bolt stationary, in
turn, and tighten its nut a
small amount (approximately two to three flats) in turn, to
press the seal fully into the housing. until the tool is in
contact with the cylinder block.
6. Remove the tool from the crankshaft.
Chec
k that the seal is located correctly.
7. Fit the drive plate. Refer to Operation 12.53.13.
8. Install the transmission. Refer to Operation 44.20. 01 in
Section 307-01A.
9. Remove the paint protection sheets and close the engine
compartment cover.
10. Connect the battery and fit the battery cover.
Re
fer to the Battery Reconnection Procedure 86.15.15.

Engine - Crankshaft Rear Seal4.0L SC V8 - AJ26
In-vehic
le Repair
Remov
a
l
S
p
ecial Tool(s)
Crankshaft Rear Oi
l Seal R
emover /
Replacer.
303 - 538
1. Open the engine compartment and fit paint protection sheets.

2. Disc
onnect the batt
ery ground cable.
Re
move the battery cover.
3. Remove the transmission. Refer to Operation 44.20. 01 in
Section 307-01B.
4. Remove the drive plat e. Refer to Operation (SC) 12.53.13.

5. Fi
t and align the seal removal tool 303 - 538 to the crankshaft.
1. Unscrew the two nuts towards the head of each bolt to allow the bolts to fit fully into the crankshaft.
2. Unscrew the center bolt until it is below the face of the main tool and position the tool to the rear of the
crankshaft.
3. Lightly tighten the two scre ws so that they fully locate
in the crankshaft.

6. Hold the tool against th e cr
an
kshaft and lightly and evenly
tighten the two nuts to the face of the tool; to secure the tool
and to hold it parallel to the face of the crankshaft.
7. Secure the oil seal to the tool using the three self-tapping