1998 HONDA INTEGRA window

Doors
Glass/Regulator/Center Glass Guide Replacement (cont'dl
5. Carefully remove the glass Jrom the window slot as
shown.
NOTE: Take care not to drop the glass inside the
door.
x
ST
20-36
6. Remove the center glass guide.
NOTE:
a Hold the adiusting bolts with a hex wrench when
removing the locknuts.
o Scribe a line around the locknuts to show the
original adjustment.
a: Nut locations
aa.2B O, 1
12 x 1 .25 mm
v1'j-
LOCKNUT
,t^
(S)t
Y-l
[ ,"*.
22 N.m (2.2 ksf.m,
Vuloru,__

>: Bolt locations
l>A.4 >8.2
d|63il;o,ilIu'- *,@
i6pl-".
- 6rbr.ftr _!
7. Disconnect the connector, and remove the regula'
tor through the cenler hole in the door.
NOTE: Scribe a line around the roller guide bolts to
show the original adlustment-
8. Remove the power window motor from the
regulator.
NOTE: Before removing the power window motor,
mark the location by scribing a line across the sec-
tor gear and regulator.
V: Bolt locations, 3
POWERwlNDowMOTOR
CONNECTOR
REGULATOR
9. Grease all the sliding surlaces of the regulator and
center glass guide where shown.
10. lnstall the power window motor on the regulator.
'l 1. Check that the regulator moves smoothly by con
necting a I2 V battery to the power window motor
(see section 23).
V: Adjusting bolt Ilocations,2 \l
\
\L
I ''II
A---- |
\H./ NOTE: Use liqurd@ thread lock.
fFtSlL!=-2
t
ICENTERGLASSGUIDE
MOTOR
(cont dI
20-37

Door
Glass/Regulator/CenterGlassGuide
Replacement (cont'd)
'12. Roll the glass up and down to see if it moves freely
without binding. Also make sure that there is no
clearance between the glass and weatherstrip when
the glass is closed. Adjust the position of the glass
as necessary (see page 20 40;.
Attach the door harness to the door correctly
page 2O-33).
Disconnect the power window switch from the
harness.
(see
14.door
When reinstalling the plastic cover, apply adhesive
along the edge where neccessary to maintain a con-
tinuous seal and prevent water leaks (see page
20 33).
16. lnstall the door panel {see page 2O-32).
Outer Molding Replacement
\NOTE: Lower the glass fully.
'1. Remove the door panel (see page 2O-32).
2. Peelthe weatherstrip away from the door (see page
2O-39i, then remove the screw.
3. Starting at the rear, pry the outer molding up and
detach the clips, then remove the outer molding.
NOTE: Take care not to twist or scratch the outer
molding.
>i Clip locations, 4 A > : Screw location, 1
>: Stabilizo. locstions, 2
.0s{0
\-
NOTEi lf necessary,replace any damagedclrps.
I ): Screw location. 1
_,f"\tjru{ 1i)
\__ -
OUTER
4. lnstallation is the reverse of the removal Drocedure.
20-38
l-
1

NOTE; Place the vehicle on a lirm, level surface when
adjusting the glass.
1 . Remove the weatherstrip (see page 20-1601.
NOTE: Check the weatherstrip lor damage and de-
terioration, and replace it if necessary
RETAINER
*T5FrHERsrR'P
\v
CENTER PILLAR
2. Install the center pillar molding.
CENTEF PILLARRETAINER
PLASTICGROMMET
3.Remove the door panel (see pages 2O-2O, 32]'.
NOTE: It necessary, peel off the plastic cover.
Remove the power mirror (see page 20-49).
5. Remove the power window switch from the front
ooor paner.
> i Screw locations, 5v: Clip locations, 3
FRONT DOOR PANEL
6. Connect the power window switch to the door har-
ness connectors.
Front:DOOR HARNESS
POWERWINDOWswtrcH
7.To prevent the glass from contacting the body, hold
the glass, and close the door carefully.
Raise the glass fully.
NOTE: Check the door fit to the body opening.
(cont'd)
20-41

15.
to,
After the clearances have been adjusted properly,
reinstall the weatherstrip.
Check that the glass contacts the weatherstrip
evenry.
NOTEr Measuring points are described on page
20-42.
Center Pillar section:
WEATHERSTRIP
17.Check for water leaks.
NOTE: Do not use high-pressure water.
18. Route the door harness and connectors, and lasten
them to the door (see pages 20'22,331.
'19. Disconnect the power window switch from the door
harness, then install the power window switch on
the door panel (see page 20-41).
20. Attach the plastic cover, then install the door panel
(see pages 2O'2o, 321.
20-47

Windshield, Rear Window, Ouarter Glass
lndex
part names show the quantities of the parts Lrsed.
UPPER MOLDINGUPPER RUBBER DAM
CLIP E, 2 White
CLIP F, 2 Lett. WhiteBight. Blue
CLIP A, 8 Red
c
f(
RETAINER, 6 Orange
CLIP B, 2 Orange
CLIP C, 2 Black
LEFT SIDE MOLDING
CLIP D, 2 Green
AINER, 2 Yellow
WINOSHIELDRemoval, page 20,55Installation, page 20 56
REAR
GLASS BRACKET, 2
,^
,r"
A
RET
a
REAR WINDOW MOLDING
UPPER FASTENER, 2(Self-adhesive-type, glass side)
UPPER FASTENER,2(Self adhesive_type, hatch side)
SIDE RUBBERDAM, 2
OUARTER GLASSRemoval, Page 20-73
SPACER,2 Installation, Page 20-73
TAPE B, 2ADHESIVE
/
Ar-/
I
BUSHING SEAL.2
Removal, page 20-61Installation, page 20-62
NOTE: The numbers after the
Hatchback
RIGHT SIDE MOLDING
'l
@q
a
e,

Windshield, Rear Window
lndex
NOTE: The numbers alter the part names show the quantities of the parts used.
Sedan
UPPER MOLDING
RIGHT SIDE MOLDING
g
e
e
WINDSHIELDRemoval, page 20-55Installation, page 20-56
bq
BEAR WINDOWRemoval, page 20 68Installation,page 20-69
UPPER RUBBER DAM
CLIP E, 2 White
cLlP F, 2 Lefr. WhireRight. Elue
CLIP A, 8 Red
\
B)
fqLOWER RUBBERDAM
A
\
RET
g
REAR WINDOW MOLDING
GLASS BRACKET, 2AINER, 2 Yellow
UPPER FASTENER, 2(Self -adhesivo-type, glass side)
#,Krrr*
FA.TENER, 2(Clip-type, body side)
LOWER COVER
20-54
&....-r,o, sPAcER, 4
q*-------..- LowEB FA'TENER, 2

{Self-adhesive-typ€,slasssid€)
LOWER FASTENER, 2(Self-adhosive-type, body sidel

Windshield
Installation (cont'd)
20-60
L.--------: -
17. Install both side moldings.'18. Let the adhesive dry Jor at least one hour, then spray
water over the windshield and check for leaks. N4ark
leaking areas, and let the windshield dry, then seal
with sealant.
NOTE:
o Let the car stand for at least four hours after wind-
shield installation. lf the car has to be used with
in the first four hours, it must be driven slowly.
a Keep the windshield dry for the first hour after
installation.
a Check that the ends ol the side molding are set
under the air scoop.
g
CLIP E
19. Reinstall all remaining removed parts.
NOTE: Advise the customer not to do the Iollow
ing things for two to three days:
a Slam the doors with all the windows rolled up.
a Twist the body excessively (such as when going
in and out of driveways at an angle or driving over
rough, uneven roads).
I
CLIP C, D