1998 HONDA INTEGRA window

r
Doors
Glass Adjustment
< : Screw locations, 5
"od} l-,/
NOTE:
a Place the vehicle on a firm, level surface when adjust-
ing the glass.
a Check the weatherstrips and glass run channel for
damage or deterioration, and replace them iI
necessarY.
1 . Remove the door panel, and peel off the plastic cover(see page 20 4).
2. Remove the power window switch from the door
panel.
DOOR PANEL
3.Connect the power window switch to the door
harness.
Make sure the guide pin is installed in the center
channel guide properly.
CENTER CHANNELGUIDE
GUIDE PIN
20-16
5. Raise the glass as iar up as possible, and hold it
against the glass run channel.
6. Loosen the roller guide bolts, and adjust the glass
so it is parallel with the glass run channel.
GUID€PIN
CENTEBCHANNELGUIDE
ROLLER GUIDE BOLTS
7. Tighten the roller guide bolts.
8. Check that the glass moves smoothly.
9. It necessary, adjust the lront and center channels.
CHANNEL
GLASS RUN CHANNEL
D\

'to.
11.
Raise the glass fully and check Ior gaps.
Check the glass operation.
NOTEi Check that the glass contacts the glass run
channel evenly.
12. Check for water leaks.
NOTE: Do not use high-pressure water.
13. Route the door harness and connectors, and fasten
them to the door (see page 2O-5).
Disconnect the power window switch lrom the door
harness, then installthe power window switch in the
door panel (see page 20 l6).
Attach the plastic cover, then install the door panel
(see page 2O-4).
14.
20-17

Doors
Front Door
Sedan
Index
Passenger's:
FRo
d"J %
ARMRESTPOCKET
1,/
gIN NERMOLDING
r '6ld
tDOORPROTECTOB
@'9.
//
/lTWEETEB
20-18
POWER WINDOWswtTcH
Replacement, page 20 20
DOOR POCKETSPEAKER COVER
\-^\
\
Qt
-N'a x^ l---r z
)r\
s'ti
7t"i
.1\N
J.-ra 1--
o t

:6
w*
S" @
PY/ DETENT

5.Detach the clips, and remove the door panel by pull
ing it upward.
NOTE: Take care not to lwist or scratch the inner
mold ing.
Disconnect the lollowing:
a Power window connectors
a Power mirror connectora Tweeter connector
l._) Clip locations, 4
INNER MOLDING
DOOR PANEL
t
INNERMOLOING
wtNDowCONNECTORS
< : Screw locations, 8
FBONT SPEAKER
6. Remove the bracket, door lock unit and front
speaker.
DOOR LOCK UNIT
7.Remove the cover panel, then disconnect the power
mirror connector (see page 20-49)
Detach the grommets and harness clips, then care-
tully remove the plastic cover.
a: Grommet localions, 2O: Harness cliplocations,3
R
*A-1
POWER MIRRORCONNECTOR
(cont'd )
20-21
::

l:
I
i'
'
Doors
Glass/Regulator/Glass Guide Replacement
1. Removel
a Door panel {see page 20 2C
a Plastic cover (see page 20-20)
2. Remove the power window switch from the door
panel, then connect the door harness (see page
20-41t.
3. Move the glass until you can see the glass stoppers,
then remove theni.
>: Glass stopper locations, 2
fo\A ^r/r r>^
{,$i}t('rQ a1l L iqW
):/}/ A/3 i,l;o,Jl*,,".r'ruf v('rsxen $flff.* a rur rrr_
Carefully move the glass until you can see the glass
mounting bolts, then remove them
NOTE: Scribe a line around the glass mounting bolts
to show the original adjustment.
>i goll locaiions. 3
'1 ,rr.^ 6 x'l o mm
L *qlqj I N m {0.8 kst m,

" 6rbrfrl
\
- a >' L;c"tio; -fil>' Locati."
\@ hN
lLoosen.
5. Carefully pull the glass out of the window slot.
NOTE: Take care not to damage location Qt on the
front sash.
GLASS
//)

Replacement (cont'dl
L Grease all the sliding surJaces of the regulatof and
glass guide where shown.
V : Adjusting boltlocations.3
4\
A
or.,-6- thread
61SILICONE GREASE
tF ht\_:-Use liquidlock.
10.
't1.
12.
r 3.
Roll the glass up and down to see if it moves lreely
without binding. Also make sure that there is no
clearance between the glass and weatherstrip when
the glass is closed. Adjust the position ot the glass
as necessary (see page 20-40).
Attach the door harness to the door correctly (see
page 20 221.
Disconnect the power window switch from the door
harness, ihen inslall the power window switch on
the door panel (see page 20 41).
When reinstalling the plastic cover, apply adhesive
along the edge where neccessary to maintain a con-
tinuous seal and prevent water leaks (see page
20 22\.
'14. Install the door panel (see page 20'21).
Doors
Glass/RegulatoriGlass Guide
I
,l
20-28
L-
Outer Molding Replacement
\
\
NOTEr Lower the glass Jully.
1. Remove:
. Door panel lsee page 2O-2O)
. Power mirror (see page 20 49)
2.
3.
Peel the weatherstrip away from the door lsee page
20 29), then remove the screw.
Starting at the rear, pry the outer molding up and
detach the clips, then remove the outer molding.
NOTE: Take care not to twist or scratch the outer
mold ing.
>: Clip locations, 4>: Screw locations, 2
L@
NOTE: lf necessary,replace any damagedclrps,
4. Installation is the reverse of the removal procedure.

Doors
Door Panel/Plastic Cover Replacement
NOTE: Take care not to scratch the door panel and other
parts.
1. Pry out the cap and remove the screw.
< : Screw location, l
Remove the inner handle trim while pulling the in-
ner handle.
Disconnect the power window switch connector.
;
,l
ti
I
I
20-32
L
Remove the armrest Pocket.
V : Scrow location, 1
/qE |
vlv/
ARMRESTPOCKET
4. Release the clips that hold the door panel.
NOTE: Remove the doo. panel with as little bend-
ing as possible to avoid creasing or breaking it.
45 mm(1.77 in)
SNAP-ON _-r'-# A177. ol /4,-.\-oquivafont 1mm +------./// 45"
{0.04 in) I
<: Clip locations, 8
5. Remove the door panel by pulling rt upward.

Latch Replacement
NOTE: Raise the glass tully.
1. Remove:
a Door panel lsee page 20-32)
a Plastic cover (see page 20-32)
a Outer handle {see page 20-34)
2. Remove the screws and dasconnect the connector,
then remove the inner handle and lalch.
NOTE: Take care not to bend the rods.
Detach the connector.
Installation is the reverse of the removal procedure
NOTE: Make sure the inner handle rod, lock rod and
connector are connected properly.
Scaew locations, 2
€tr' l-,/
Glass/Regulatol/Center Glass
Guide Replacement
BOLT8 x 1.25 mm22 N.n 12.2 kgl'm.16 lbt.ft)
a Door panel (see page 20 32)a Plastic cover (see page 20-32)
Connect the power window switch to the door har-
ness (see page 20-41).
Peel the weatherstrip away from the door (see page
Loosen the inside stabilizers.
NOTEr Scribe a line around the bolts to show the
original adjustment.
Carefully move the glass until you can see the glass
mounting nuts, then remove them.
STAEILIZER
a: Nut locations, 2
t,h6xl.omm)@[ a ru.m ro.8 ksr'm.
i
6 tbritl
\
INSIDE STABILIZERS
(cont'd )
20-35