1997 SSANGYONG KORANDO engine

OM600 ENGINE MECHANICAL 1B3 -- 61
D AEW OO M Y_2000
38. Replace the O -- ring of heater feed pipe and install it
to the cylinder head.
Notice
For installation, clean the hole.
39. Install the bracket of heater feed pipe to the oil filter.
40. Install the fuel pipe and the accelerator control link-
age.
41. Connect the fuel lines to the injection nozzles and to
the injection pump.
Tightening Torque18 N∙m (13 lb-ft)
Box Wrench Insert 000 589 77 03 00

1B3 -- 62 OM600 ENGINE MECHANICAL
D AEW OO M Y_2000
42. Install the poly V-- belt.
Notice
Be careful not to contaminate the belt.
43. By inserting a rod into the tensioning lever upper
hole and pulling the rod, install the bolt and then
tighten the nut.
Tightening Torque23 N∙m (17 lb-ft)
44. Install the oil dipstick tube bracket.
Tightening Torque10 N∙m(89lb-in)
45. Hold the cooling fan with the counter holder and
tighten the bolt.

OM600 ENGINE MECHANICAL 1B3 -- 63
D AEW OO M Y_2000
TIMING CASE COVER
Preceding Work : Removal of the cooling fan
Rmoval of the V-- belt tensioning device
Removal of the vibration damper and hub
Removal of the generator
1 Bolt 10N∙m (89 lb-in) .....................
2 Cylinder Head Cover
3 Gasket Replace..........................
4 Socket Bolt 25N∙m (18 lb-ft) ................
5 Fuel Filter
6 Square Nut
7OilPan
8 Socket Bolt 10N∙m (89 lb-in) ...............
9 Bolt M6 : 10N∙m (89 lb-in) ................
M8 : 23N∙m (17 lb-ft)
10 Power Steering Pump
11 Bolt
12 Belt Pulley13 Bolt 32N∙m (24 lb-ft) ......................
14 Timing Case Cover
15 Bolt 23N∙m (17 lb-ft) ......................
16 Generator Bracket
17 Bolt 45N∙m (33 lb-ft) ......................
18 Bolt 25N∙m (18 lb-ft) ......................
19 Bolt 10N∙m(89lb-in) .....................
20 Closing Cover
21 Socket Bolt 23N∙m (17 lb-ft) ................
22 Guide Pulley
23 Bolt 9N∙m(80lb-in) .......................
24 Guide Pulley Bracket
25 Nut 23N∙m (17 lb-ft) .......................

1B3 -- 64 OM600 ENGINE MECHANICAL
D AEW OO M Y_2000
Tools Required
116 589 03 07 00 Socket Wrench
Removal Procedure
1. Remove the fan clutch and cooling fan belt pulley.
2. Drain the engine oil completely.
3. Remove the oil dipstick tube bracket bolts.
4. Remove the crankshaft pulley.
5. Loosen the bolt (1) and then remove the cylinder
head cover (2) and gasket.
6. Remove the vacuum pump.
7. Detach the closing cover (20). Remove the bolts(21)
and then remove the guide pulley (22).
8. Remove the guide pulley bracket (24).

OM600 ENGINE MECHANICAL 1B3 -- 65
D AEW OO M Y_2000
9. Disconnect the pipes of power steering pump and
remove the belt pulley.
Notice
Be careful not to lose the key.
10. Remove the nut and pull out the bolt and then re-
move the power steering pump.
11. Remove the generator bracket (16).
12. Remove the fuel filter.

1B3 -- 66 OM600 ENGINE MECHANICAL
D AEW OO M Y_2000
13. Remove the camshaft.
14. Remove the socket bolts(4) in the chain box.
Socket Wrench 115 589 03 07 00
15. Remove the injection pump.
Notice
See the “Removal of fuel injection pump”.
16. Remove the oil pan bolts (8, 9) in the area of the tim-
ing case cover (14).
17. Slightly loosen the remaining oil pan bolts.
18. Remove the timing case cover (19) bolts and then
remove the timing case cover (14).
Notice
Be careful not to damage the cylinder head gasket
or oil pan gasket.

OM600 ENGINE MECHANICAL 1B3 -- 67
D AEW OO M Y_2000
Installation Procedure
1. Thoroughly clean the sealing surface and apply
sealant.
2. Install the timing case cover.
Tightening Torque10 N∙m(89lb-in)
Notice
Bolts arrangement
1.M6 x 60
2.M6 x 70
3.M6 x 40
3. Tighten the socket bolts in the chain box.
Tightening Torque23 N∙m (17 lb-ft)
4. Tighten the oil pan bolts.
Tihi
Socket bolt10 N∙m (89 lb-in)
Tightening
TorqueM6 bolt10 N∙m (89 lb-in)TorqueM8 bolt23 N∙m (17 lb-ft)

1B3 -- 68 OM600 ENGINE MECHANICAL
D AEW OO M Y_2000
5. Install the flange, vibration damper and crankshaft
belt pulley.
Notice
Replace front radial seal if necessary.
6. Install the generator bracket.
TighteningFront25 N∙m (18 lb-ft)Tightening
To r q u eSide25 N∙m (18 lb-ft)
7. Install the generator.
TighteningTorqueUpper--25N∙m (18 lb-ft)TighteningTorqueLow -- 25 N∙m (18 lb-ft)
8. Install the cylinder head cover.
Tightening Torque10 N∙m(89lb-in)
9. Tighten the injection pump mounting bolts.
Tightening Torque23 N∙m (17 lb-ft)